The following information is also available:
Time column is TIME ORDERED-> Fetching fa950717_0421.1830.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 80108476.217200 80159452.046600
Data file start and stop ascatime : 80108476.217200 80159452.046600
Aspecting run start and stop ascatime : 80108476.217325 80159452.046522
Time interval averaged over (seconds) : 50975.829197
Total pointing and manuver time (sec) : 30925.478516 20050.480469
Mean boresight Euler angles : 24.230885 103.126260 20.413088
RA DEC SUN ANGLE
Mean solar position (deg) : 115.33 21.40
Mean aberration (arcsec) : -0.91 7.75
Mean sat X-axis (deg) : 145.623280 -65.883301 90.26
Mean sat Y-axis (deg) : 109.399960 19.856955 5.76
Mean sat Z-axis (deg) : 24.230885 -13.126260 95.75
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 24.425341 -12.914345 290.457306 0.062448
Minimum 24.375341 -12.916265 290.401001 0.000000
Maximum 24.440887 -12.798913 290.495026 7.518122
Sigma (RMS) 0.000110 0.000165 0.002590 0.065054
Number of ASPECT records processed = 30061
Aspecting to RA/DEC : 24.42534065 -12.91434479
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 24.425 DEC: -12.914
START TIME: SC 80108476.2173 = UT 17/07/95 04:21:16
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000103 1.530 2603 1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
159.999619 0.527 2603 1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
635.998108 0.079 F828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
2875.990723 0.013 F820C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 7
6395.978516 0.000 F828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
8635.971680 0.074 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
12155.958984 0.095 F828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
14331.952148 0.073 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
17851.939453 0.088 F828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
20091.933594 0.051 D820C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 3
23611.919922 0.019 F828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
25825.914062 0.044 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
29371.902344 0.033 F828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
31579.894531 0.018 F820C3 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 7
35131.882812 0.036 F828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
37323.875000 0.086 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
40891.863281 0.067 F828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
43069.855469 0.078 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
46587.843750 0.069 F828C3 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 7
48815.835938 0.076 2003 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
50975.828125 7.518 3603 1 1 0 0 0 0 0 0 0 1 1 0 1 1 0 0 0
Attitude Records: 30061
Attitude Steps: 21
Maneuver ACM time: 20050.5 sec
Pointed ACM time: 30925.5 sec
-> Calculating aspect point93 90 count=1 sum1=24.181 sum2=103.011 sum3=20.358 98 101 count=27525 sum1=666945 sum2=2.83854e+06 sum3=561890 98 102 count=2403 sum1=58227.9 sum2=247817 sum3=49043.5 99 100 count=22 sum1=533.277 sum2=2268.47 sum3=449.605 99 101 count=105 sum1=2544.6 sum2=10828 sum3=2143.77 100 99 count=2 sum1=48.486 sum2=206.212 sum3=40.896 100 100 count=2 sum1=48.486 sum2=206.214 sum3=40.891 0 out of 30060 points outside bin structure-> Euler angles: 24.2306, 103.126, 20.4135
Interpolating 12 records in time interval 8.01594e+07 - 8.01595e+07
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft950717_0421.1830",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft950717_0421.1830 Initial mode = 2 (Bright) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 2 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 396352 Bright = 84992 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 0 PH = 480320 MPC = 0 PCAL = 0 Memory Check = 1024 Number of superframes = 7640 no. of SIS events found = 1220310-> Standard Error Output From FTOOL frfread
coordinate error 0 0 coordinate error 510 317 coordinate error 0 0 coordinate error 1 256 coordinate error 0 384 coordinate error 12 0 coordinate error 400 0 coordinate error 0 24-> Removing the following files with NEVENTS=0
ft950717_0421_1830G200470L.fits ft950717_0421_1830G200570H.fits ft950717_0421_1830G200670H.fits ft950717_0421_1830G200770H.fits ft950717_0421_1830G200870H.fits ft950717_0421_1830G200970H.fits ft950717_0421_1830G201970M.fits ft950717_0421_1830G202070L.fits ft950717_0421_1830G202170H.fits ft950717_0421_1830G202270H.fits ft950717_0421_1830G202370H.fits ft950717_0421_1830G203070H.fits ft950717_0421_1830G203170H.fits ft950717_0421_1830G203673H.fits ft950717_0421_1830G204070M.fits ft950717_0421_1830G204170L.fits ft950717_0421_1830G204270L.fits ft950717_0421_1830G204370M.fits ft950717_0421_1830G300470L.fits ft950717_0421_1830G300570H.fits ft950717_0421_1830G300670H.fits ft950717_0421_1830G300770H.fits ft950717_0421_1830G300870H.fits ft950717_0421_1830G301970M.fits ft950717_0421_1830G302070L.fits ft950717_0421_1830G302170H.fits ft950717_0421_1830G303070H.fits ft950717_0421_1830G303170H.fits ft950717_0421_1830G303270H.fits ft950717_0421_1830G303573H.fits ft950717_0421_1830G303970M.fits ft950717_0421_1830G304070L.fits ft950717_0421_1830G304170L.fits ft950717_0421_1830S000701L.fits ft950717_0421_1830S001102L.fits ft950717_0421_1830S001201H.fits ft950717_0421_1830S001401L.fits ft950717_0421_1830S001502L.fits ft950717_0421_1830S001899.fits ft950717_0421_1830S002001L.fits ft950717_0421_1830S002302M.fits ft950717_0421_1830S002402L.fits ft950717_0421_1830S002502M.fits ft950717_0421_1830S003601M.fits ft950717_0421_1830S004301M.fits ft950717_0421_1830S004801L.fits ft950717_0421_1830S005101M.fits ft950717_0421_1830S100701L.fits ft950717_0421_1830S101102L.fits ft950717_0421_1830S101201H.fits ft950717_0421_1830S101401L.fits ft950717_0421_1830S101502L.fits ft950717_0421_1830S101899.fits ft950717_0421_1830S102001L.fits ft950717_0421_1830S102302M.fits ft950717_0421_1830S102402L.fits ft950717_0421_1830S102502M.fits ft950717_0421_1830S103601M.fits ft950717_0421_1830S104301M.fits ft950717_0421_1830S104801L.fits ft950717_0421_1830S105101M.fits-> Checking for empty GTI extensions
ft950717_0421_1830S000102M.fits[3] ft950717_0421_1830S000202L.fits[3] ft950717_0421_1830S000302L.fits[3] ft950717_0421_1830S000402L.fits[3] ft950717_0421_1830S000501L.fits[3] ft950717_0421_1830S000601H.fits[3] ft950717_0421_1830S000802L.fits[3] ft950717_0421_1830S000902M.fits[3] ft950717_0421_1830S001002M.fits[3] ft950717_0421_1830S001301H.fits[3] ft950717_0421_1830S001601L.fits[3] ft950717_0421_1830S001701H.fits[3] ft950717_0421_1830S001901H.fits[3] ft950717_0421_1830S002102L.fits[3] ft950717_0421_1830S002202M.fits[3] ft950717_0421_1830S002602M.fits[3] ft950717_0421_1830S002702L.fits[3] ft950717_0421_1830S002802M.fits[3] ft950717_0421_1830S002902M.fits[3] ft950717_0421_1830S003002M.fits[3] ft950717_0421_1830S003102L.fits[3] ft950717_0421_1830S003202M.fits[3] ft950717_0421_1830S003301H.fits[3] ft950717_0421_1830S003401H.fits[3] ft950717_0421_1830S003501H.fits[3] ft950717_0421_1830S003702M.fits[3] ft950717_0421_1830S003802L.fits[3] ft950717_0421_1830S003902M.fits[3] ft950717_0421_1830S004002L.fits[3] ft950717_0421_1830S004102M.fits[3] ft950717_0421_1830S004201H.fits[3] ft950717_0421_1830S004402M.fits[3] ft950717_0421_1830S004502L.fits[3] ft950717_0421_1830S004602M.fits[3] ft950717_0421_1830S004701H.fits[3] ft950717_0421_1830S004902L.fits[3] ft950717_0421_1830S005001H.fits[3] ft950717_0421_1830S005202M.fits[3]-> Merging GTIs from the following files:
ft950717_0421_1830S100102M.fits[3] ft950717_0421_1830S100202L.fits[3] ft950717_0421_1830S100302L.fits[3] ft950717_0421_1830S100402L.fits[3] ft950717_0421_1830S100501L.fits[3] ft950717_0421_1830S100601H.fits[3] ft950717_0421_1830S100802L.fits[3] ft950717_0421_1830S100902M.fits[3] ft950717_0421_1830S101002M.fits[3] ft950717_0421_1830S101301H.fits[3] ft950717_0421_1830S101601L.fits[3] ft950717_0421_1830S101701H.fits[3] ft950717_0421_1830S101901H.fits[3] ft950717_0421_1830S102102L.fits[3] ft950717_0421_1830S102202M.fits[3] ft950717_0421_1830S102602M.fits[3] ft950717_0421_1830S102702L.fits[3] ft950717_0421_1830S102802M.fits[3] ft950717_0421_1830S102902M.fits[3] ft950717_0421_1830S103002M.fits[3] ft950717_0421_1830S103102L.fits[3] ft950717_0421_1830S103202M.fits[3] ft950717_0421_1830S103301H.fits[3] ft950717_0421_1830S103401H.fits[3] ft950717_0421_1830S103501H.fits[3] ft950717_0421_1830S103702M.fits[3] ft950717_0421_1830S103802L.fits[3] ft950717_0421_1830S103902M.fits[3] ft950717_0421_1830S104002L.fits[3] ft950717_0421_1830S104102M.fits[3] ft950717_0421_1830S104201H.fits[3] ft950717_0421_1830S104402M.fits[3] ft950717_0421_1830S104502L.fits[3] ft950717_0421_1830S104602M.fits[3] ft950717_0421_1830S104701H.fits[3] ft950717_0421_1830S104902L.fits[3] ft950717_0421_1830S105001H.fits[3] ft950717_0421_1830S105202M.fits[3]-> Merging GTIs from the following files:
ft950717_0421_1830G200170M.fits[3] ft950717_0421_1830G200270L.fits[3] ft950717_0421_1830G200370L.fits[3] ft950717_0421_1830G201070H.fits[3] ft950717_0421_1830G201170H.fits[3] ft950717_0421_1830G201270H.fits[3] ft950717_0421_1830G201370L.fits[3] ft950717_0421_1830G201470L.fits[3] ft950717_0421_1830G201570M.fits[3] ft950717_0421_1830G201670M.fits[3] ft950717_0421_1830G201770M.fits[3] ft950717_0421_1830G201870M.fits[3] ft950717_0421_1830G202470H.fits[3] ft950717_0421_1830G202570H.fits[3] ft950717_0421_1830G202670L.fits[3] ft950717_0421_1830G202770L.fits[3] ft950717_0421_1830G202870H.fits[3] ft950717_0421_1830G202970H.fits[3] ft950717_0421_1830G203270H.fits[3] ft950717_0421_1830G203370H.fits[3] ft950717_0421_1830G203470H.fits[3] ft950717_0421_1830G203570H.fits[3] ft950717_0421_1830G203770H.fits[3] ft950717_0421_1830G203870L.fits[3] ft950717_0421_1830G203970M.fits[3] ft950717_0421_1830G204470M.fits[3] ft950717_0421_1830G204570L.fits[3] ft950717_0421_1830G204670L.fits[3] ft950717_0421_1830G204770M.fits[3] ft950717_0421_1830G204870M.fits[3] ft950717_0421_1830G204970M.fits[3] ft950717_0421_1830G205070L.fits[3] ft950717_0421_1830G205170M.fits[3] ft950717_0421_1830G205270H.fits[3] ft950717_0421_1830G205370H.fits[3] ft950717_0421_1830G205470H.fits[3] ft950717_0421_1830G205570M.fits[3] ft950717_0421_1830G205670L.fits[3] ft950717_0421_1830G205770M.fits[3] ft950717_0421_1830G205870L.fits[3] ft950717_0421_1830G205970M.fits[3] ft950717_0421_1830G206070M.fits[3] ft950717_0421_1830G206170M.fits[3] ft950717_0421_1830G206270M.fits[3] ft950717_0421_1830G206370M.fits[3] ft950717_0421_1830G206470M.fits[3] ft950717_0421_1830G206570H.fits[3] ft950717_0421_1830G206670M.fits[3] ft950717_0421_1830G206770L.fits[3] ft950717_0421_1830G206870M.fits[3] ft950717_0421_1830G206970M.fits[3] ft950717_0421_1830G207070M.fits[3] ft950717_0421_1830G207170M.fits[3] ft950717_0421_1830G207270H.fits[3] ft950717_0421_1830G207370L.fits[3] ft950717_0421_1830G207470L.fits[3] ft950717_0421_1830G207570H.fits[3] ft950717_0421_1830G207670H.fits[3] ft950717_0421_1830G207770H.fits[3] ft950717_0421_1830G207870H.fits[3] ft950717_0421_1830G207970H.fits[3] ft950717_0421_1830G208070H.fits[3] ft950717_0421_1830G208170H.fits[3] ft950717_0421_1830G208270H.fits[3] ft950717_0421_1830G208370H.fits[3] ft950717_0421_1830G208470H.fits[3] ft950717_0421_1830G208570H.fits[3] ft950717_0421_1830G208670H.fits[3] ft950717_0421_1830G208770M.fits[3]-> Merging GTIs from the following files:
ft950717_0421_1830G300170M.fits[3] ft950717_0421_1830G300270L.fits[3] ft950717_0421_1830G300370L.fits[3] ft950717_0421_1830G300970H.fits[3] ft950717_0421_1830G301070H.fits[3] ft950717_0421_1830G301170H.fits[3] ft950717_0421_1830G301270H.fits[3] ft950717_0421_1830G301370L.fits[3] ft950717_0421_1830G301470L.fits[3] ft950717_0421_1830G301570M.fits[3] ft950717_0421_1830G301670M.fits[3] ft950717_0421_1830G301770M.fits[3] ft950717_0421_1830G301870M.fits[3] ft950717_0421_1830G302270H.fits[3] ft950717_0421_1830G302370H.fits[3] ft950717_0421_1830G302470H.fits[3] ft950717_0421_1830G302570H.fits[3] ft950717_0421_1830G302670L.fits[3] ft950717_0421_1830G302770L.fits[3] ft950717_0421_1830G302870H.fits[3] ft950717_0421_1830G302970H.fits[3] ft950717_0421_1830G303370H.fits[3] ft950717_0421_1830G303470H.fits[3] ft950717_0421_1830G303670H.fits[3] ft950717_0421_1830G303770L.fits[3] ft950717_0421_1830G303870M.fits[3] ft950717_0421_1830G304270M.fits[3] ft950717_0421_1830G304370M.fits[3] ft950717_0421_1830G304470M.fits[3] ft950717_0421_1830G304570L.fits[3] ft950717_0421_1830G304670L.fits[3] ft950717_0421_1830G304770M.fits[3] ft950717_0421_1830G304870M.fits[3] ft950717_0421_1830G304970M.fits[3] ft950717_0421_1830G305070M.fits[3] ft950717_0421_1830G305170L.fits[3] ft950717_0421_1830G305270M.fits[3] ft950717_0421_1830G305370H.fits[3] ft950717_0421_1830G305470H.fits[3] ft950717_0421_1830G305570H.fits[3] ft950717_0421_1830G305670M.fits[3] ft950717_0421_1830G305770L.fits[3] ft950717_0421_1830G305870M.fits[3] ft950717_0421_1830G305970L.fits[3] ft950717_0421_1830G306070M.fits[3] ft950717_0421_1830G306170M.fits[3] ft950717_0421_1830G306270M.fits[3] ft950717_0421_1830G306370M.fits[3] ft950717_0421_1830G306470M.fits[3] ft950717_0421_1830G306570M.fits[3] ft950717_0421_1830G306670H.fits[3] ft950717_0421_1830G306770M.fits[3] ft950717_0421_1830G306870L.fits[3] ft950717_0421_1830G306970M.fits[3] ft950717_0421_1830G307070M.fits[3] ft950717_0421_1830G307170M.fits[3] ft950717_0421_1830G307270M.fits[3] ft950717_0421_1830G307370H.fits[3] ft950717_0421_1830G307470H.fits[3] ft950717_0421_1830G307570H.fits[3] ft950717_0421_1830G307670L.fits[3] ft950717_0421_1830G307770L.fits[3] ft950717_0421_1830G307870H.fits[3] ft950717_0421_1830G307970H.fits[3] ft950717_0421_1830G308070H.fits[3] ft950717_0421_1830G308170H.fits[3] ft950717_0421_1830G308270H.fits[3] ft950717_0421_1830G308370H.fits[3] ft950717_0421_1830G308470H.fits[3] ft950717_0421_1830G308570H.fits[3] ft950717_0421_1830G308670H.fits[3] ft950717_0421_1830G308770H.fits[3] ft950717_0421_1830G308870H.fits[3] ft950717_0421_1830G308970H.fits[3] ft950717_0421_1830G309070M.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200370h.prelist merge count = 2 photon cnt = 5 GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g200770h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g200870h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g201070h.prelist merge count = 13 photon cnt = 11447 GISSORTSPLIT:LO:g201170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201370h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g201470h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g201570h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g201670h.prelist merge count = 1 photon cnt = 414 GISSORTSPLIT:LO:g200170l.prelist merge count = 1 photon cnt = 112 GISSORTSPLIT:LO:g200270l.prelist merge count = 10 photon cnt = 11396 GISSORTSPLIT:LO:g200370l.prelist merge count = 4 photon cnt = 487 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200270m.prelist merge count = 14 photon cnt = 15104 GISSORTSPLIT:LO:g200370m.prelist merge count = 3 photon cnt = 85 GISSORTSPLIT:LO:g200470m.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g200570m.prelist merge count = 1 photon cnt = 14 GISSORTSPLIT:LO:g200670m.prelist merge count = 1 photon cnt = 35 GISSORTSPLIT:LO:g200770m.prelist merge count = 1 photon cnt = 27 GISSORTSPLIT:LO:g200870m.prelist merge count = 1 photon cnt = 15 GISSORTSPLIT:LO:g200970m.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:g201070m.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:Total filenames split = 69 GISSORTSPLIT:LO:Total split file cnt = 29 GISSORTSPLIT:LO:End program-> Creating ad83069000g200170m.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950717_0421_1830G200170M.fits 2 -- ft950717_0421_1830G201870M.fits 3 -- ft950717_0421_1830G203970M.fits 4 -- ft950717_0421_1830G204470M.fits 5 -- ft950717_0421_1830G204770M.fits 6 -- ft950717_0421_1830G204970M.fits 7 -- ft950717_0421_1830G205170M.fits 8 -- ft950717_0421_1830G205570M.fits 9 -- ft950717_0421_1830G205770M.fits 10 -- ft950717_0421_1830G206270M.fits 11 -- ft950717_0421_1830G206470M.fits 12 -- ft950717_0421_1830G206670M.fits 13 -- ft950717_0421_1830G207170M.fits 14 -- ft950717_0421_1830G208770M.fits Merging binary extension #: 2 1 -- ft950717_0421_1830G200170M.fits 2 -- ft950717_0421_1830G201870M.fits 3 -- ft950717_0421_1830G203970M.fits 4 -- ft950717_0421_1830G204470M.fits 5 -- ft950717_0421_1830G204770M.fits 6 -- ft950717_0421_1830G204970M.fits 7 -- ft950717_0421_1830G205170M.fits 8 -- ft950717_0421_1830G205570M.fits 9 -- ft950717_0421_1830G205770M.fits 10 -- ft950717_0421_1830G206270M.fits 11 -- ft950717_0421_1830G206470M.fits 12 -- ft950717_0421_1830G206670M.fits 13 -- ft950717_0421_1830G207170M.fits 14 -- ft950717_0421_1830G208770M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83069000g200270h.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950717_0421_1830G201270H.fits 2 -- ft950717_0421_1830G202570H.fits 3 -- ft950717_0421_1830G202870H.fits 4 -- ft950717_0421_1830G203570H.fits 5 -- ft950717_0421_1830G205270H.fits 6 -- ft950717_0421_1830G205470H.fits 7 -- ft950717_0421_1830G206570H.fits 8 -- ft950717_0421_1830G207270H.fits 9 -- ft950717_0421_1830G207870H.fits 10 -- ft950717_0421_1830G208070H.fits 11 -- ft950717_0421_1830G208270H.fits 12 -- ft950717_0421_1830G208470H.fits 13 -- ft950717_0421_1830G208670H.fits Merging binary extension #: 2 1 -- ft950717_0421_1830G201270H.fits 2 -- ft950717_0421_1830G202570H.fits 3 -- ft950717_0421_1830G202870H.fits 4 -- ft950717_0421_1830G203570H.fits 5 -- ft950717_0421_1830G205270H.fits 6 -- ft950717_0421_1830G205470H.fits 7 -- ft950717_0421_1830G206570H.fits 8 -- ft950717_0421_1830G207270H.fits 9 -- ft950717_0421_1830G207870H.fits 10 -- ft950717_0421_1830G208070H.fits 11 -- ft950717_0421_1830G208270H.fits 12 -- ft950717_0421_1830G208470H.fits 13 -- ft950717_0421_1830G208670H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83069000g200370l.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950717_0421_1830G200270L.fits 2 -- ft950717_0421_1830G201470L.fits 3 -- ft950717_0421_1830G202770L.fits 4 -- ft950717_0421_1830G203870L.fits 5 -- ft950717_0421_1830G204670L.fits 6 -- ft950717_0421_1830G205070L.fits 7 -- ft950717_0421_1830G205670L.fits 8 -- ft950717_0421_1830G205870L.fits 9 -- ft950717_0421_1830G206770L.fits 10 -- ft950717_0421_1830G207470L.fits Merging binary extension #: 2 1 -- ft950717_0421_1830G200270L.fits 2 -- ft950717_0421_1830G201470L.fits 3 -- ft950717_0421_1830G202770L.fits 4 -- ft950717_0421_1830G203870L.fits 5 -- ft950717_0421_1830G204670L.fits 6 -- ft950717_0421_1830G205070L.fits 7 -- ft950717_0421_1830G205670L.fits 8 -- ft950717_0421_1830G205870L.fits 9 -- ft950717_0421_1830G206770L.fits 10 -- ft950717_0421_1830G207470L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000487 events
ft950717_0421_1830G201370L.fits ft950717_0421_1830G202670L.fits ft950717_0421_1830G204570L.fits ft950717_0421_1830G207370L.fits-> Ignoring the following files containing 000000414 events
ft950717_0421_1830G203770H.fits-> Ignoring the following files containing 000000112 events
ft950717_0421_1830G200370L.fits-> Ignoring the following files containing 000000085 events
ft950717_0421_1830G201770M.fits ft950717_0421_1830G206170M.fits ft950717_0421_1830G207070M.fits-> Ignoring the following files containing 000000035 events
ft950717_0421_1830G201570M.fits-> Ignoring the following files containing 000000027 events
ft950717_0421_1830G201670M.fits-> Ignoring the following files containing 000000015 events
ft950717_0421_1830G205970M.fits-> Ignoring the following files containing 000000014 events
ft950717_0421_1830G206970M.fits-> Ignoring the following files containing 000000010 events
ft950717_0421_1830G206070M.fits-> Ignoring the following files containing 000000008 events
ft950717_0421_1830G206870M.fits-> Ignoring the following files containing 000000007 events
ft950717_0421_1830G208170H.fits-> Ignoring the following files containing 000000006 events
ft950717_0421_1830G203470H.fits-> Ignoring the following files containing 000000006 events
ft950717_0421_1830G206370M.fits-> Ignoring the following files containing 000000006 events
ft950717_0421_1830G205370H.fits-> Ignoring the following files containing 000000005 events
ft950717_0421_1830G201170H.fits ft950717_0421_1830G202470H.fits-> Ignoring the following files containing 000000004 events
ft950717_0421_1830G208370H.fits-> Ignoring the following files containing 000000004 events
ft950717_0421_1830G208570H.fits-> Ignoring the following files containing 000000003 events
ft950717_0421_1830G203370H.fits-> Ignoring the following files containing 000000003 events
ft950717_0421_1830G207670H.fits-> Ignoring the following files containing 000000002 events
ft950717_0421_1830G207570H.fits-> Ignoring the following files containing 000000002 events
ft950717_0421_1830G207770H.fits-> Ignoring the following files containing 000000002 events
ft950717_0421_1830G202970H.fits-> Ignoring the following files containing 000000002 events
ft950717_0421_1830G201070H.fits-> Ignoring the following files containing 000000001 events
ft950717_0421_1830G207970H.fits-> Ignoring the following files containing 000000001 events
ft950717_0421_1830G204870M.fits-> Ignoring the following files containing 000000001 events
ft950717_0421_1830G203270H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300270h.prelist merge count = 2 photon cnt = 2 GISSORTSPLIT:LO:g300370h.prelist merge count = 2 photon cnt = 3 GISSORTSPLIT:LO:g300470h.prelist merge count = 2 photon cnt = 3 GISSORTSPLIT:LO:g300570h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300870h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g300970h.prelist merge count = 14 photon cnt = 10773 GISSORTSPLIT:LO:g301070h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g301170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g301270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g301370h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301570h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g301670h.prelist merge count = 1 photon cnt = 394 GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 112 GISSORTSPLIT:LO:g300270l.prelist merge count = 10 photon cnt = 10595 GISSORTSPLIT:LO:g300370l.prelist merge count = 4 photon cnt = 474 GISSORTSPLIT:LO:g300170m.prelist merge count = 2 photon cnt = 3 GISSORTSPLIT:LO:g300270m.prelist merge count = 2 photon cnt = 28 GISSORTSPLIT:LO:g300370m.prelist merge count = 14 photon cnt = 14255 GISSORTSPLIT:LO:g300470m.prelist merge count = 3 photon cnt = 54 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 17 GISSORTSPLIT:LO:g300670m.prelist merge count = 1 photon cnt = 16 GISSORTSPLIT:LO:g300770m.prelist merge count = 1 photon cnt = 32 GISSORTSPLIT:LO:g300870m.prelist merge count = 1 photon cnt = 29 GISSORTSPLIT:LO:g300970m.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g301070m.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g301170m.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:Total filenames split = 75 GISSORTSPLIT:LO:Total split file cnt = 30 GISSORTSPLIT:LO:End program-> Creating ad83069000g300170m.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950717_0421_1830G300170M.fits 2 -- ft950717_0421_1830G301870M.fits 3 -- ft950717_0421_1830G303870M.fits 4 -- ft950717_0421_1830G304470M.fits 5 -- ft950717_0421_1830G304770M.fits 6 -- ft950717_0421_1830G305070M.fits 7 -- ft950717_0421_1830G305270M.fits 8 -- ft950717_0421_1830G305670M.fits 9 -- ft950717_0421_1830G305870M.fits 10 -- ft950717_0421_1830G306370M.fits 11 -- ft950717_0421_1830G306570M.fits 12 -- ft950717_0421_1830G306770M.fits 13 -- ft950717_0421_1830G307270M.fits 14 -- ft950717_0421_1830G309070M.fits Merging binary extension #: 2 1 -- ft950717_0421_1830G300170M.fits 2 -- ft950717_0421_1830G301870M.fits 3 -- ft950717_0421_1830G303870M.fits 4 -- ft950717_0421_1830G304470M.fits 5 -- ft950717_0421_1830G304770M.fits 6 -- ft950717_0421_1830G305070M.fits 7 -- ft950717_0421_1830G305270M.fits 8 -- ft950717_0421_1830G305670M.fits 9 -- ft950717_0421_1830G305870M.fits 10 -- ft950717_0421_1830G306370M.fits 11 -- ft950717_0421_1830G306570M.fits 12 -- ft950717_0421_1830G306770M.fits 13 -- ft950717_0421_1830G307270M.fits 14 -- ft950717_0421_1830G309070M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83069000g300270h.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950717_0421_1830G301270H.fits 2 -- ft950717_0421_1830G302570H.fits 3 -- ft950717_0421_1830G302870H.fits 4 -- ft950717_0421_1830G303470H.fits 5 -- ft950717_0421_1830G305370H.fits 6 -- ft950717_0421_1830G305570H.fits 7 -- ft950717_0421_1830G306670H.fits 8 -- ft950717_0421_1830G307370H.fits 9 -- ft950717_0421_1830G307570H.fits 10 -- ft950717_0421_1830G308170H.fits 11 -- ft950717_0421_1830G308370H.fits 12 -- ft950717_0421_1830G308570H.fits 13 -- ft950717_0421_1830G308770H.fits 14 -- ft950717_0421_1830G308970H.fits Merging binary extension #: 2 1 -- ft950717_0421_1830G301270H.fits 2 -- ft950717_0421_1830G302570H.fits 3 -- ft950717_0421_1830G302870H.fits 4 -- ft950717_0421_1830G303470H.fits 5 -- ft950717_0421_1830G305370H.fits 6 -- ft950717_0421_1830G305570H.fits 7 -- ft950717_0421_1830G306670H.fits 8 -- ft950717_0421_1830G307370H.fits 9 -- ft950717_0421_1830G307570H.fits 10 -- ft950717_0421_1830G308170H.fits 11 -- ft950717_0421_1830G308370H.fits 12 -- ft950717_0421_1830G308570H.fits 13 -- ft950717_0421_1830G308770H.fits 14 -- ft950717_0421_1830G308970H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83069000g300370l.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950717_0421_1830G300270L.fits 2 -- ft950717_0421_1830G301470L.fits 3 -- ft950717_0421_1830G302770L.fits 4 -- ft950717_0421_1830G303770L.fits 5 -- ft950717_0421_1830G304670L.fits 6 -- ft950717_0421_1830G305170L.fits 7 -- ft950717_0421_1830G305770L.fits 8 -- ft950717_0421_1830G305970L.fits 9 -- ft950717_0421_1830G306870L.fits 10 -- ft950717_0421_1830G307770L.fits Merging binary extension #: 2 1 -- ft950717_0421_1830G300270L.fits 2 -- ft950717_0421_1830G301470L.fits 3 -- ft950717_0421_1830G302770L.fits 4 -- ft950717_0421_1830G303770L.fits 5 -- ft950717_0421_1830G304670L.fits 6 -- ft950717_0421_1830G305170L.fits 7 -- ft950717_0421_1830G305770L.fits 8 -- ft950717_0421_1830G305970L.fits 9 -- ft950717_0421_1830G306870L.fits 10 -- ft950717_0421_1830G307770L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000474 events
ft950717_0421_1830G301370L.fits ft950717_0421_1830G302670L.fits ft950717_0421_1830G304570L.fits ft950717_0421_1830G307670L.fits-> Ignoring the following files containing 000000394 events
ft950717_0421_1830G303670H.fits-> Ignoring the following files containing 000000112 events
ft950717_0421_1830G300370L.fits-> Ignoring the following files containing 000000054 events
ft950717_0421_1830G301770M.fits ft950717_0421_1830G306270M.fits ft950717_0421_1830G307170M.fits-> Ignoring the following files containing 000000032 events
ft950717_0421_1830G301570M.fits-> Ignoring the following files containing 000000029 events
ft950717_0421_1830G301670M.fits-> Ignoring the following files containing 000000028 events
ft950717_0421_1830G304370M.fits ft950717_0421_1830G304970M.fits-> Ignoring the following files containing 000000017 events
ft950717_0421_1830G306070M.fits-> Ignoring the following files containing 000000016 events
ft950717_0421_1830G306170M.fits-> Ignoring the following files containing 000000011 events
ft950717_0421_1830G306470M.fits-> Ignoring the following files containing 000000011 events
ft950717_0421_1830G306970M.fits-> Ignoring the following files containing 000000008 events
ft950717_0421_1830G307070M.fits-> Ignoring the following files containing 000000006 events
ft950717_0421_1830G308670H.fits-> Ignoring the following files containing 000000005 events
ft950717_0421_1830G305470H.fits-> Ignoring the following files containing 000000005 events
ft950717_0421_1830G308270H.fits-> Ignoring the following files containing 000000004 events
ft950717_0421_1830G308870H.fits-> Ignoring the following files containing 000000003 events
ft950717_0421_1830G302970H.fits-> Ignoring the following files containing 000000003 events
ft950717_0421_1830G308470H.fits-> Ignoring the following files containing 000000003 events
ft950717_0421_1830G301170H.fits ft950717_0421_1830G302470H.fits-> Ignoring the following files containing 000000003 events
ft950717_0421_1830G301070H.fits ft950717_0421_1830G302370H.fits-> Ignoring the following files containing 000000003 events
ft950717_0421_1830G304270M.fits ft950717_0421_1830G304870M.fits-> Ignoring the following files containing 000000002 events
ft950717_0421_1830G307870H.fits-> Ignoring the following files containing 000000002 events
ft950717_0421_1830G308070H.fits-> Ignoring the following files containing 000000002 events
ft950717_0421_1830G300970H.fits ft950717_0421_1830G302270H.fits-> Ignoring the following files containing 000000002 events
ft950717_0421_1830G303370H.fits-> Ignoring the following files containing 000000001 events
ft950717_0421_1830G307470H.fits-> Ignoring the following files containing 000000001 events
ft950717_0421_1830G307970H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 1 photon cnt = 149 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 9 photon cnt = 279667 SIS0SORTSPLIT:LO:s000301l.prelist merge count = 2 photon cnt = 112 SIS0SORTSPLIT:LO:s000402l.prelist merge count = 10 photon cnt = 68617 SIS0SORTSPLIT:LO:s000502l.prelist merge count = 1 photon cnt = 252 SIS0SORTSPLIT:LO:s000602m.prelist merge count = 13 photon cnt = 228575 SIS0SORTSPLIT:LO:s000702m.prelist merge count = 2 photon cnt = 260 SIS0SORTSPLIT:LO:Total filenames split = 38 SIS0SORTSPLIT:LO:Total split file cnt = 7 SIS0SORTSPLIT:LO:End program-> Creating ad83069000s000101h.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950717_0421_1830S000601H.fits 2 -- ft950717_0421_1830S001301H.fits 3 -- ft950717_0421_1830S001701H.fits 4 -- ft950717_0421_1830S001901H.fits 5 -- ft950717_0421_1830S003301H.fits 6 -- ft950717_0421_1830S003501H.fits 7 -- ft950717_0421_1830S004201H.fits 8 -- ft950717_0421_1830S004701H.fits 9 -- ft950717_0421_1830S005001H.fits Merging binary extension #: 2 1 -- ft950717_0421_1830S000601H.fits 2 -- ft950717_0421_1830S001301H.fits 3 -- ft950717_0421_1830S001701H.fits 4 -- ft950717_0421_1830S001901H.fits 5 -- ft950717_0421_1830S003301H.fits 6 -- ft950717_0421_1830S003501H.fits 7 -- ft950717_0421_1830S004201H.fits 8 -- ft950717_0421_1830S004701H.fits 9 -- ft950717_0421_1830S005001H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83069000s000202m.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950717_0421_1830S000102M.fits 2 -- ft950717_0421_1830S000902M.fits 3 -- ft950717_0421_1830S002202M.fits 4 -- ft950717_0421_1830S002602M.fits 5 -- ft950717_0421_1830S002802M.fits 6 -- ft950717_0421_1830S003002M.fits 7 -- ft950717_0421_1830S003202M.fits 8 -- ft950717_0421_1830S003702M.fits 9 -- ft950717_0421_1830S003902M.fits 10 -- ft950717_0421_1830S004102M.fits 11 -- ft950717_0421_1830S004402M.fits 12 -- ft950717_0421_1830S004602M.fits 13 -- ft950717_0421_1830S005202M.fits Merging binary extension #: 2 1 -- ft950717_0421_1830S000102M.fits 2 -- ft950717_0421_1830S000902M.fits 3 -- ft950717_0421_1830S002202M.fits 4 -- ft950717_0421_1830S002602M.fits 5 -- ft950717_0421_1830S002802M.fits 6 -- ft950717_0421_1830S003002M.fits 7 -- ft950717_0421_1830S003202M.fits 8 -- ft950717_0421_1830S003702M.fits 9 -- ft950717_0421_1830S003902M.fits 10 -- ft950717_0421_1830S004102M.fits 11 -- ft950717_0421_1830S004402M.fits 12 -- ft950717_0421_1830S004602M.fits 13 -- ft950717_0421_1830S005202M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83069000s000302l.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950717_0421_1830S000202L.fits 2 -- ft950717_0421_1830S000402L.fits 3 -- ft950717_0421_1830S000802L.fits 4 -- ft950717_0421_1830S002102L.fits 5 -- ft950717_0421_1830S002702L.fits 6 -- ft950717_0421_1830S003102L.fits 7 -- ft950717_0421_1830S003802L.fits 8 -- ft950717_0421_1830S004002L.fits 9 -- ft950717_0421_1830S004502L.fits 10 -- ft950717_0421_1830S004902L.fits Merging binary extension #: 2 1 -- ft950717_0421_1830S000202L.fits 2 -- ft950717_0421_1830S000402L.fits 3 -- ft950717_0421_1830S000802L.fits 4 -- ft950717_0421_1830S002102L.fits 5 -- ft950717_0421_1830S002702L.fits 6 -- ft950717_0421_1830S003102L.fits 7 -- ft950717_0421_1830S003802L.fits 8 -- ft950717_0421_1830S004002L.fits 9 -- ft950717_0421_1830S004502L.fits 10 -- ft950717_0421_1830S004902L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000260 events
ft950717_0421_1830S001002M.fits ft950717_0421_1830S002902M.fits-> Ignoring the following files containing 000000252 events
ft950717_0421_1830S000302L.fits-> Ignoring the following files containing 000000149 events
ft950717_0421_1830S003401H.fits-> Ignoring the following files containing 000000112 events
ft950717_0421_1830S000501L.fits ft950717_0421_1830S001601L.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 9 photon cnt = 296252 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 1 photon cnt = 191 SIS1SORTSPLIT:LO:s100301l.prelist merge count = 2 photon cnt = 112 SIS1SORTSPLIT:LO:s100402l.prelist merge count = 10 photon cnt = 77669 SIS1SORTSPLIT:LO:s100502l.prelist merge count = 1 photon cnt = 192 SIS1SORTSPLIT:LO:s100602m.prelist merge count = 13 photon cnt = 267992 SIS1SORTSPLIT:LO:s100702m.prelist merge count = 2 photon cnt = 262 SIS1SORTSPLIT:LO:Total filenames split = 38 SIS1SORTSPLIT:LO:Total split file cnt = 7 SIS1SORTSPLIT:LO:End program-> Creating ad83069000s100101h.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950717_0421_1830S100601H.fits 2 -- ft950717_0421_1830S101301H.fits 3 -- ft950717_0421_1830S101701H.fits 4 -- ft950717_0421_1830S101901H.fits 5 -- ft950717_0421_1830S103301H.fits 6 -- ft950717_0421_1830S103501H.fits 7 -- ft950717_0421_1830S104201H.fits 8 -- ft950717_0421_1830S104701H.fits 9 -- ft950717_0421_1830S105001H.fits Merging binary extension #: 2 1 -- ft950717_0421_1830S100601H.fits 2 -- ft950717_0421_1830S101301H.fits 3 -- ft950717_0421_1830S101701H.fits 4 -- ft950717_0421_1830S101901H.fits 5 -- ft950717_0421_1830S103301H.fits 6 -- ft950717_0421_1830S103501H.fits 7 -- ft950717_0421_1830S104201H.fits 8 -- ft950717_0421_1830S104701H.fits 9 -- ft950717_0421_1830S105001H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83069000s100202m.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950717_0421_1830S100102M.fits 2 -- ft950717_0421_1830S100902M.fits 3 -- ft950717_0421_1830S102202M.fits 4 -- ft950717_0421_1830S102602M.fits 5 -- ft950717_0421_1830S102802M.fits 6 -- ft950717_0421_1830S103002M.fits 7 -- ft950717_0421_1830S103202M.fits 8 -- ft950717_0421_1830S103702M.fits 9 -- ft950717_0421_1830S103902M.fits 10 -- ft950717_0421_1830S104102M.fits 11 -- ft950717_0421_1830S104402M.fits 12 -- ft950717_0421_1830S104602M.fits 13 -- ft950717_0421_1830S105202M.fits Merging binary extension #: 2 1 -- ft950717_0421_1830S100102M.fits 2 -- ft950717_0421_1830S100902M.fits 3 -- ft950717_0421_1830S102202M.fits 4 -- ft950717_0421_1830S102602M.fits 5 -- ft950717_0421_1830S102802M.fits 6 -- ft950717_0421_1830S103002M.fits 7 -- ft950717_0421_1830S103202M.fits 8 -- ft950717_0421_1830S103702M.fits 9 -- ft950717_0421_1830S103902M.fits 10 -- ft950717_0421_1830S104102M.fits 11 -- ft950717_0421_1830S104402M.fits 12 -- ft950717_0421_1830S104602M.fits 13 -- ft950717_0421_1830S105202M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad83069000s100302l.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft950717_0421_1830S100202L.fits 2 -- ft950717_0421_1830S100402L.fits 3 -- ft950717_0421_1830S100802L.fits 4 -- ft950717_0421_1830S102102L.fits 5 -- ft950717_0421_1830S102702L.fits 6 -- ft950717_0421_1830S103102L.fits 7 -- ft950717_0421_1830S103802L.fits 8 -- ft950717_0421_1830S104002L.fits 9 -- ft950717_0421_1830S104502L.fits 10 -- ft950717_0421_1830S104902L.fits Merging binary extension #: 2 1 -- ft950717_0421_1830S100202L.fits 2 -- ft950717_0421_1830S100402L.fits 3 -- ft950717_0421_1830S100802L.fits 4 -- ft950717_0421_1830S102102L.fits 5 -- ft950717_0421_1830S102702L.fits 6 -- ft950717_0421_1830S103102L.fits 7 -- ft950717_0421_1830S103802L.fits 8 -- ft950717_0421_1830S104002L.fits 9 -- ft950717_0421_1830S104502L.fits 10 -- ft950717_0421_1830S104902L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000262 events
ft950717_0421_1830S101002M.fits ft950717_0421_1830S102902M.fits-> Ignoring the following files containing 000000192 events
ft950717_0421_1830S100302L.fits-> Ignoring the following files containing 000000191 events
ft950717_0421_1830S103401H.fits-> Ignoring the following files containing 000000112 events
ft950717_0421_1830S100501L.fits ft950717_0421_1830S101601L.fits-> Tar-ing together the leftover raw files
a ft950717_0421_1830G200370L.fits 43K a ft950717_0421_1830G201070H.fits 40K a ft950717_0421_1830G201170H.fits 40K a ft950717_0421_1830G201370L.fits 43K a ft950717_0421_1830G201570M.fits 40K a ft950717_0421_1830G201670M.fits 40K a ft950717_0421_1830G201770M.fits 40K a ft950717_0421_1830G202470H.fits 40K a ft950717_0421_1830G202670L.fits 43K a ft950717_0421_1830G202970H.fits 40K a ft950717_0421_1830G203270H.fits 40K a ft950717_0421_1830G203370H.fits 40K a ft950717_0421_1830G203470H.fits 40K a ft950717_0421_1830G203770H.fits 51K a ft950717_0421_1830G204570L.fits 43K a ft950717_0421_1830G204870M.fits 40K a ft950717_0421_1830G205370H.fits 40K a ft950717_0421_1830G205970M.fits 40K a ft950717_0421_1830G206070M.fits 40K a ft950717_0421_1830G206170M.fits 40K a ft950717_0421_1830G206370M.fits 40K a ft950717_0421_1830G206870M.fits 40K a ft950717_0421_1830G206970M.fits 40K a ft950717_0421_1830G207070M.fits 40K a ft950717_0421_1830G207370L.fits 43K a ft950717_0421_1830G207570H.fits 40K a ft950717_0421_1830G207670H.fits 40K a ft950717_0421_1830G207770H.fits 40K a ft950717_0421_1830G207970H.fits 40K a ft950717_0421_1830G208170H.fits 40K a ft950717_0421_1830G208370H.fits 40K a ft950717_0421_1830G208570H.fits 40K a ft950717_0421_1830G300370L.fits 43K a ft950717_0421_1830G300970H.fits 40K a ft950717_0421_1830G301070H.fits 40K a ft950717_0421_1830G301170H.fits 40K a ft950717_0421_1830G301370L.fits 43K a ft950717_0421_1830G301570M.fits 40K a ft950717_0421_1830G301670M.fits 40K a ft950717_0421_1830G301770M.fits 40K a ft950717_0421_1830G302270H.fits 40K a ft950717_0421_1830G302370H.fits 40K a ft950717_0421_1830G302470H.fits 40K a ft950717_0421_1830G302670L.fits 43K a ft950717_0421_1830G302970H.fits 40K a ft950717_0421_1830G303370H.fits 40K a ft950717_0421_1830G303670H.fits 51K a ft950717_0421_1830G304270M.fits 40K a ft950717_0421_1830G304370M.fits 40K a ft950717_0421_1830G304570L.fits 43K a ft950717_0421_1830G304870M.fits 40K a ft950717_0421_1830G304970M.fits 40K a ft950717_0421_1830G305470H.fits 40K a ft950717_0421_1830G306070M.fits 40K a ft950717_0421_1830G306170M.fits 40K a ft950717_0421_1830G306270M.fits 40K a ft950717_0421_1830G306470M.fits 40K a ft950717_0421_1830G306970M.fits 40K a ft950717_0421_1830G307070M.fits 40K a ft950717_0421_1830G307170M.fits 40K a ft950717_0421_1830G307470H.fits 40K a ft950717_0421_1830G307670L.fits 43K a ft950717_0421_1830G307870H.fits 40K a ft950717_0421_1830G307970H.fits 40K a ft950717_0421_1830G308070H.fits 40K a ft950717_0421_1830G308270H.fits 40K a ft950717_0421_1830G308470H.fits 40K a ft950717_0421_1830G308670H.fits 40K a ft950717_0421_1830G308870H.fits 40K a ft950717_0421_1830S000302L.fits 45K a ft950717_0421_1830S000501L.fits 40K a ft950717_0421_1830S001002M.fits 43K a ft950717_0421_1830S001601L.fits 40K a ft950717_0421_1830S002902M.fits 43K a ft950717_0421_1830S003401H.fits 45K a ft950717_0421_1830S100302L.fits 43K a ft950717_0421_1830S100501L.fits 40K a ft950717_0421_1830S101002M.fits 43K a ft950717_0421_1830S101601L.fits 40K a ft950717_0421_1830S102902M.fits 43K a ft950717_0421_1830S103401H.fits 45K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft950717_0421.1830 'ft950717_0421.1830' is successfully opened Data Start Time is 80108472.22 (950717 042112) Time Margin 2.0 sec included Sync error detected in 2862 th SF Sync error detected in 2890 th SF Sync error detected in 5708 th SF Sync error detected in 5946 th SF Sync error detected in 5947 th SF Sync error detected in 5949 th SF Sync error detected in 5952 th SF Sync error detected in 5961 th SF Sync error detected in 5962 th SF Sync error detected in 5983 th SF Sync error detected in 6110 th SF Sync error detected in 6166 th SF Sync error detected in 6181 th SF Sync error detected in 6191 th SF Sync error detected in 6194 th SF Sync error detected in 6253 th SF Sync error detected in 6256 th SF Sync error detected in 6270 th SF Sync error detected in 6440 th SF Sync error detected in 7219 th SF Sync error detected in 7231 th SF Sync error detected in 7277 th SF Sync error detected in 7371 th SF Sync error detected in 7372 th SF Sync error detected in 7480 th SF Sync error detected in 7483 th SF Sync error detected in 7488 th SF Sync error detected in 7515 th SF Sync error detected in 7544 th SF 'ft950717_0421.1830' EOF detected, sf=7640 Data End Time is 80159452.05 (950717 183052) Gain History is written in ft950717_0421_1830.ghf-> Checking if column CAL_START in ft950717_0421_1830.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft950717_0421_1830.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad83069000g200270h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000g200370l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000g300170m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000g300270h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000g300370l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000s000202m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000s000302l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000s100202m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad83069000s100302l.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 95/ 7/17 4:21 mjd=49915.181250 Orbit file name is ./frf.orbit.211 Epoch of Orbital Elements: 1995/7/10 9:59:59 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa950717_0421.1830 S0-HK file: ft950717_0421_1830S0HK.fits S1-HK file: ft950717_0421_1830S1HK.fits G2-HK file: ft950717_0421_1830G2HK.fits G3-HK file: ft950717_0421_1830G3HK.fits output FITS File: ft950717_0421_1830.mkf Total 1593 Data bins were processed.-> Checking if column TIME in ft950717_0421_1830.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 9464.4876 The mean of the selected column is 34.541926 The standard deviation of the selected column is 17.850030 The minimum of selected column is 11.553611 The maximum of selected column is 169.50056 The number of points used in calculation is 274-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 7068.6565 The mean of the selected column is 25.798017 The standard deviation of the selected column is 16.809705 The minimum of selected column is 10.553607 The maximum of selected column is 156.62552 The number of points used in calculation is 274-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<88 )&& (S0_PIXL1>0.0 && S0_PIXL1<76.2 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.12E+05 187090 1100
Processing file: /data/data18/seq_proc/83069000.004/ad83069000s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
174755 126609 0 48146 0 0
Writing events file
126609 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
174755 126609 0 48146 0 0
in 8473.05 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/83069000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/83069000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 126609
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 95 85667
Flickering pixels iter, pixels & cnts : 1 45 1844
cleaning chip # 1
Hot pixels & counts : 49 36399
Flickering pixels iter, pixels & cnts : 1 34 838
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 223
Number of (internal) image counts : 126609
Number of image cts rejected (N, %) : 124748 98.5301208
By chip : 0 1 2 3
Pixels rejected : 140 83 0 0
Image counts : 88003 38606 0 0
Image cts rejected: 87511 37237 0 0
Image cts rej (%) : 99.44 96.45 0.00 0.00
filtering data...
Total counts : 88003 38606 0 0
Total cts rejected: 87511 37237 0 0
Total cts rej (%) : 99.44 96.45 0.00 0.00
Number of clean counts accepted : 1861
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 223
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad83069000s000102h.evt use_events=no
Wrote cleaned events file to ad83069000s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad83069000s000112h.unf into ad83069000s000112h.evtThe sum of the selected column is 9464.4876 The mean of the selected column is 34.541926 The standard deviation of the selected column is 17.850030 The minimum of selected column is 11.553611 The maximum of selected column is 169.50056 The number of points used in calculation is 274-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 7068.6565 The mean of the selected column is 25.798017 The standard deviation of the selected column is 16.809705 The minimum of selected column is 10.553607 The maximum of selected column is 156.62552 The number of points used in calculation is 274-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<88 )&& (S0_PIXL1>0.0 && S0_PIXL1<76.2 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT2 HIGH 17/07/95 05:12:18 0.12E+05 187559 1100
Processing file: /data/data18/seq_proc/83069000.004/ad83069000s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
175380 126992 0 48388 0 0
Writing events file
126992 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
175380 126992 0 48388 0 0
in 8473.05 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/83069000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/83069000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 126992
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 95 85897
Flickering pixels iter, pixels & cnts : 1 45 1852
cleaning chip # 1
Hot pixels & counts : 49 36459
Flickering pixels iter, pixels & cnts : 1 34 843
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 223
Number of (internal) image counts : 126992
Number of image cts rejected (N, %) : 125051 98.4715576
By chip : 0 1 2 3
Pixels rejected : 140 83 0 0
Image counts : 88282 38710 0 0
Image cts rejected: 87749 37302 0 0
Image cts rej (%) : 99.40 96.36 0.00 0.00
filtering data...
Total counts : 88282 38710 0 0
Total cts rejected: 87749 37302 0 0
Total cts rej (%) : 99.40 96.36 0.00 0.00
Number of clean counts accepted : 1941
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 223
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad83069000s000112h.evt use_events=no
Wrote cleaned events file to ad83069000s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad83069000s000202m.unf into ad83069000s000202m.evtThe sum of the selected column is 9602.1674 The mean of the selected column is 33.929920 The standard deviation of the selected column is 10.926935 The minimum of selected column is 16.625057 The maximum of selected column is 101.65659 The number of points used in calculation is 283-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 7404.0247 The mean of the selected column is 26.162631 The standard deviation of the selected column is 10.084695 The minimum of selected column is 9.0312805 The maximum of selected column is 83.031525 The number of points used in calculation is 283-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>1.1 && S0_PIXL0<66.7 )&& (S0_PIXL1>0.0 && S0_PIXL1<56.4 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT MEDIUM 17/07/95 04:21:18 0.15E+05 228575 1100
Processing file: /data/data18/seq_proc/83069000.004/ad83069000s000202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
209656 132744 0 76912 0 0
Writing events file
132744 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
209656 132744 0 76912 0 0
in 8884.53 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/83069000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/83069000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 132744
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 96 89434
Flickering pixels iter, pixels & cnts : 1 46 1859
cleaning chip # 1
Hot pixels & counts : 51 38316
Flickering pixels iter, pixels & cnts : 1 26 752
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 219
Number of (internal) image counts : 132744
Number of image cts rejected (N, %) : 130361 98.2048187
By chip : 0 1 2 3
Pixels rejected : 142 77 0 0
Image counts : 92218 40526 0 0
Image cts rejected: 91293 39068 0 0
Image cts rej (%) : 99.00 96.40 0.00 0.00
filtering data...
Total counts : 92218 40526 0 0
Total cts rejected: 91293 39068 0 0
Total cts rej (%) : 99.00 96.40 0.00 0.00
Number of clean counts accepted : 2383
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 219
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad83069000s000202m.evt use_events=no
Wrote cleaned events file to ad83069000s000202m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad83069000s000302l.unf into ad83069000s000302l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT LOW 17/07/95 04:30:38 0.17E+05 68617 1100
Processing file: /data/data18/seq_proc/83069000.004/ad83069000s000302l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/83069000.004/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/83069000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/83069000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000s000302l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad83069000s000302l.evt use_events=no
Wrote cleaned events file to ad83069000s000302l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad83069000s000302l.evt since it contains 0 eventsThe sum of the selected column is 11374.038 The mean of the selected column is 41.360139 The standard deviation of the selected column is 28.175086 The minimum of selected column is 14.375050 The maximum of selected column is 249.75084 The number of points used in calculation is 275-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 12577.850 The mean of the selected column is 45.737637 The standard deviation of the selected column is 29.342809 The minimum of selected column is 15.531303 The maximum of selected column is 216.78197 The number of points used in calculation is 275-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<125.8 )&& (S1_PIXL3>0.0 && S1_PIXL3<133.7 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.12E+05 209110 0011
Processing file: /data/data18/seq_proc/83069000.004/ad83069000s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
192818 139369 0 53449 0 0
Writing events file
139369 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
192818 139369 0 53449 0 0
in 8500.50 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/83069000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/83069000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 139369
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 83 65297
Flickering pixels iter, pixels & cnts : 1 66 2917
cleaning chip # 3
Hot pixels & counts : 81 65916
Flickering pixels iter, pixels & cnts : 1 120 3571
Flickering pixels iter, pixels & cnts : 2 1 4
Number of pixels rejected : 351
Number of (internal) image counts : 139369
Number of image cts rejected (N, %) : 137705 98.8060455
By chip : 0 1 2 3
Pixels rejected : 0 0 149 202
Image counts : 0 0 68782 70587
Image cts rejected: 0 0 68214 69491
Image cts rej (%) : 0.00 0.00 99.17 98.45
filtering data...
Total counts : 0 0 68782 70587
Total cts rejected: 0 0 68214 69491
Total cts rej (%) : 0.00 0.00 99.17 98.45
Number of clean counts accepted : 1664
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 351
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad83069000s100102h.evt use_events=no
Wrote cleaned events file to ad83069000s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad83069000s100112h.unf into ad83069000s100112h.evtThe sum of the selected column is 11374.038 The mean of the selected column is 41.360139 The standard deviation of the selected column is 28.175086 The minimum of selected column is 14.375050 The maximum of selected column is 249.75084 The number of points used in calculation is 275-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 12577.850 The mean of the selected column is 45.737637 The standard deviation of the selected column is 29.342809 The minimum of selected column is 15.531303 The maximum of selected column is 216.78197 The number of points used in calculation is 275-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<125.8 )&& (S1_PIXL3>0.0 && S1_PIXL3<133.7 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT2 HIGH 17/07/95 05:12:18 0.12E+05 209560 0011
Processing file: /data/data18/seq_proc/83069000.004/ad83069000s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
193845 140044 0 53801 0 0
Writing events file
140044 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
193845 140044 0 53801 0 0
in 8500.50 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/83069000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/83069000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 140044
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 83 65584
Flickering pixels iter, pixels & cnts : 1 66 2927
cleaning chip # 3
Hot pixels & counts : 81 66175
Flickering pixels iter, pixels & cnts : 1 120 3610
Flickering pixels iter, pixels & cnts : 2 1 4
Number of pixels rejected : 351
Number of (internal) image counts : 140044
Number of image cts rejected (N, %) : 138300 98.7546768
By chip : 0 1 2 3
Pixels rejected : 0 0 149 202
Image counts : 0 0 69123 70921
Image cts rejected: 0 0 68511 69789
Image cts rej (%) : 0.00 0.00 99.11 98.40
filtering data...
Total counts : 0 0 69123 70921
Total cts rejected: 0 0 68511 69789
Total cts rej (%) : 0.00 0.00 99.11 98.40
Number of clean counts accepted : 1744
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 351
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad83069000s100112h.evt use_events=no
Wrote cleaned events file to ad83069000s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad83069000s100202m.unf into ad83069000s100202m.evtThe sum of the selected column is 12519.854 The mean of the selected column is 44.239768 The standard deviation of the selected column is 16.275427 The minimum of selected column is 16.250055 The maximum of selected column is 108.68787 The number of points used in calculation is 283-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 13385.524 The mean of the selected column is 47.298671 The standard deviation of the selected column is 19.978662 The minimum of selected column is 15.281301 The maximum of selected column is 176.37560 The number of points used in calculation is 283-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<93 )&& (S1_PIXL3>0.0 && S1_PIXL3<107.2 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT MEDIUM 17/07/95 04:21:18 0.15E+05 267992 0011
Processing file: /data/data18/seq_proc/83069000.004/ad83069000s100202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
246487 147706 0 98781 0 0
Writing events file
147706 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
246487 147706 0 98781 0 0
in 8774.91 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/83069000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/83069000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 147706
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 85 69272
Flickering pixels iter, pixels & cnts : 1 68 2868
Flickering pixels iter, pixels & cnts : 2 1 6
cleaning chip # 3
Hot pixels & counts : 81 68848
Flickering pixels iter, pixels & cnts : 1 129 4274
Flickering pixels iter, pixels & cnts : 2 1 4
Number of pixels rejected : 365
Number of (internal) image counts : 147706
Number of image cts rejected (N, %) : 145272 98.3521347
By chip : 0 1 2 3
Pixels rejected : 0 0 154 211
Image counts : 0 0 73253 74453
Image cts rejected: 0 0 72146 73126
Image cts rej (%) : 0.00 0.00 98.49 98.22
filtering data...
Total counts : 0 0 73253 74453
Total cts rejected: 0 0 72146 73126
Total cts rej (%) : 0.00 0.00 98.49 98.22
Number of clean counts accepted : 2434
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 365
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad83069000s100202m.evt use_events=no
Wrote cleaned events file to ad83069000s100202m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad83069000s100302l.unf into ad83069000s100302l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT LOW 17/07/95 04:30:38 0.17E+05 77669 0011
Processing file: /data/data18/seq_proc/83069000.004/ad83069000s100302l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/83069000.004/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data18/seq_proc/83069000.004/screen_in_event.xsl
reading data file: /data/data18/seq_proc/83069000.004/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad83069000s100302l.evt use_events=no
Wrote cleaned events file to ad83069000s100302l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad83069000s100302l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.14E+05 15104 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.unf
Total Good Bad: Region Time Phase Cut
15104 3542 8332 3230 0 0
Writing events file
3542 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15104 3542 8332 3230 0 0
in 8479.90 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
3542 3162 380
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad83069000g200170m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 3162 in ad83069000g200170m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH HIGH 17/07/95 05:15:40 0.11E+05 11447 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.unf
Total Good Bad: Region Time Phase Cut
11447 3717 6632 1098 0 0
Writing events file
3717 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11447 3717 6632 1098 0 0
in 9118.17 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
3717 3360 357
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad83069000g200270h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 3360 in ad83069000g200270h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH LOW 17/07/95 04:30:50 0.16E+05 11396 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/83069000.004/ad83069000g200370l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad83069000g200370l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad83069000g200370l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.14E+05 14255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.unf
Total Good Bad: Region Time Phase Cut
14255 3683 7049 3523 0 0
Writing events file
3683 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14255 3683 7049 3523 0 0
in 8447.90 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
3683 3272 411
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad83069000g300170m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 3272 in ad83069000g300170m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH HIGH 17/07/95 05:15:42 0.11E+05 10773 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.unf
Total Good Bad: Region Time Phase Cut
10773 4047 5551 1175 0 0
Writing events file
4047 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10773 4047 5551 1175 0 0
in 9114.17 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
4047 3580 467
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad83069000g300270h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 3580 in ad83069000g300270h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH LOW 17/07/95 04:30:50 0.16E+05 10595 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/83069000.004/ad83069000g300370l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!screen:ASCA > read events ad83069000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad83069000g300370l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad83069000g300370l.evt since it contains 0 events-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad83069000g200170m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950717_0421.1830
making an exposure map...
Aspect RA/DEC/ROLL : 24.4251 -12.9141 290.4571
Mean RA/DEC/ROLL : 24.4265 -12.9349 290.4571
Pnt RA/DEC/ROLL : 24.4358 -12.8722 290.4571
Image rebin factor : 1
Attitude Records : 30074
GTI intervals : 21
Total GTI (secs) : 8479.902
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1328.0739746 1328.0739746
20 Percent Complete: Total/live time: 2906.0620117 2906.0620117
30 Percent Complete: Total/live time: 2906.0620117 2906.0620117
40 Percent Complete: Total/live time: 3616.0598145 3616.0598145
50 Percent Complete: Total/live time: 4562.0478516 4562.0478516
60 Percent Complete: Total/live time: 6992.0400391 6992.0400391
70 Percent Complete: Total/live time: 6992.0400391 6992.0400391
80 Percent Complete: Total/live time: 7121.9169922 7121.9169922
90 Percent Complete: Total/live time: 7808.0463867 7808.0463867
100 Percent Complete: Total/live time: 8479.9023438 8479.9023438
Number of attitude steps used: 23
Number of attitude steps avail: 9866
Mean RA/DEC pixel offset: -9.4330 -2.8535
writing expo file: ad83069000g200170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83069000g200170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83069000g200170m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.85E+04 3162 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.evt
Total Good Bad: Region Time Phase Cut
3162 3131 31 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3162 3131 31 0 0 0
in 8479.90 seconds
Image has 3131 counts for 0.3692 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.evt
Total Good Bad: Region Time Phase Cut
3162 1453 31 0 0 1678
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3162 1453 31 0 0 1678
in 8479.90 seconds
Image has 1453 counts for 0.1713 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.evt
Total Good Bad: Region Time Phase Cut
3162 1691 31 0 0 1440
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3162 1691 31 0 0 1440
in 8479.90 seconds
Image has 1691 counts for 0.1994 counts/sec
Command not found; type ? for a command listing
!ad83069000g200170m:ASCA >
!ad83069000g200170m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83069000g200170m:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!ad83069000g200170m:ASCA > read events ad83069000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!ad83069000g200170m:ASCA-GIS2-PH > set image sky
!ad83069000g200170m:ASCA-GIS2-PH > filter region corner_point.reg
!ad83069000g200170m:ASCA-GIS2-PH > extract image
!ad83069000g200170m:ASCA-GIS2-PH > save image outfile=ad83069000g200170m.img
Wrote image to file ad83069000g200170m.img
!ad83069000g200170m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad83069000g200170m:ASCA-GIS2-PH > extract image
!ad83069000g200170m:ASCA-GIS2-PH > save image outfile=ad83069000g200170m_lo.img
Wrote image to file ad83069000g200170m_lo.img
!ad83069000g200170m:ASCA-GIS2-PH > clear pha_cut
!ad83069000g200170m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad83069000g200170m:ASCA-GIS2-PH > extract image
!ad83069000g200170m:ASCA-GIS2-PH > save image outfile=ad83069000g200170m_hi.img
Wrote image to file ad83069000g200170m_hi.img
!ad83069000g200170m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad83069000g200270h.expo
ASCAEXPO_V0.9b
reading data file: ad83069000g200270h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950717_0421.1830
making an exposure map...
Aspect RA/DEC/ROLL : 24.4251 -12.9141 290.4571
Mean RA/DEC/ROLL : 24.4258 -12.9350 290.4571
Pnt RA/DEC/ROLL : 24.4249 -12.8913 290.4571
Image rebin factor : 1
Attitude Records : 30074
GTI intervals : 54
Total GTI (secs) : 9118.174
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1502.0107422 1502.0107422
20 Percent Complete: Total/live time: 2844.0415039 2844.0415039
30 Percent Complete: Total/live time: 2844.0415039 2844.0415039
40 Percent Complete: Total/live time: 4610.0341797 4610.0341797
50 Percent Complete: Total/live time: 4928.1591797 4928.1591797
60 Percent Complete: Total/live time: 5721.0302734 5721.0302734
70 Percent Complete: Total/live time: 7444.1728516 7444.1728516
80 Percent Complete: Total/live time: 7444.1728516 7444.1728516
90 Percent Complete: Total/live time: 9118.1728516 9118.1728516
100 Percent Complete: Total/live time: 9118.1728516 9118.1728516
Number of attitude steps used: 19
Number of attitude steps avail: 24262
Mean RA/DEC pixel offset: -9.3765 -3.0055
writing expo file: ad83069000g200270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83069000g200270h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83069000g200270h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH HIGH 17/07/95 05:15:40 0.91E+04 3360 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.evt
Total Good Bad: Region Time Phase Cut
3360 3322 38 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3360 3322 38 0 0 0
in 9118.17 seconds
Image has 3322 counts for 0.3643 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.evt
Total Good Bad: Region Time Phase Cut
3360 1549 38 0 0 1773
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3360 1549 38 0 0 1773
in 9118.17 seconds
Image has 1549 counts for 0.1699 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.evt
Total Good Bad: Region Time Phase Cut
3360 1781 38 0 0 1541
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3360 1781 38 0 0 1541
in 9118.17 seconds
Image has 1781 counts for 0.1953 counts/sec
Command not found; type ? for a command listing
!ad83069000g200270h:ASCA >
!ad83069000g200270h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83069000g200270h:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!ad83069000g200270h:ASCA > read events ad83069000g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!ad83069000g200270h:ASCA-GIS2-PH > set image sky
!ad83069000g200270h:ASCA-GIS2-PH > filter region corner_point.reg
!ad83069000g200270h:ASCA-GIS2-PH > extract image
!ad83069000g200270h:ASCA-GIS2-PH > save image outfile=ad83069000g200270h.img
Wrote image to file ad83069000g200270h.img
!ad83069000g200270h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad83069000g200270h:ASCA-GIS2-PH > extract image
!ad83069000g200270h:ASCA-GIS2-PH > save image outfile=ad83069000g200270h_lo.img
Wrote image to file ad83069000g200270h_lo.img
!ad83069000g200270h:ASCA-GIS2-PH > clear pha_cut
!ad83069000g200270h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad83069000g200270h:ASCA-GIS2-PH > extract image
!ad83069000g200270h:ASCA-GIS2-PH > save image outfile=ad83069000g200270h_hi.img
Wrote image to file ad83069000g200270h_hi.img
!ad83069000g200270h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad83069000g300170m.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad83069000g300170m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950717_0421.1830
making an exposure map...
Aspect RA/DEC/ROLL : 24.4251 -12.9141 290.4586
Mean RA/DEC/ROLL : 24.4200 -12.9109 290.4586
Pnt RA/DEC/ROLL : 24.4423 -12.8963 290.4586
Image rebin factor : 1
Attitude Records : 30074
GTI intervals : 21
Total GTI (secs) : 8447.902
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1312.0740967 1312.0740967
20 Percent Complete: Total/live time: 2874.0622559 2874.0622559
30 Percent Complete: Total/live time: 2874.0622559 2874.0622559
40 Percent Complete: Total/live time: 3584.0600586 3584.0600586
50 Percent Complete: Total/live time: 4530.0478516 4530.0478516
60 Percent Complete: Total/live time: 6960.0400391 6960.0400391
70 Percent Complete: Total/live time: 6960.0400391 6960.0400391
80 Percent Complete: Total/live time: 7089.9169922 7089.9169922
90 Percent Complete: Total/live time: 7776.0463867 7776.0463867
100 Percent Complete: Total/live time: 8447.9023438 8447.9023438
Number of attitude steps used: 23
Number of attitude steps avail: 9858
Mean RA/DEC pixel offset: 2.1205 -1.7058
writing expo file: ad83069000g300170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83069000g300170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83069000g300170m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.84E+04 3272 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.evt
Total Good Bad: Region Time Phase Cut
3272 3239 33 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3272 3239 33 0 0 0
in 8447.90 seconds
Image has 3239 counts for 0.3834 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.evt
Total Good Bad: Region Time Phase Cut
3272 1487 33 0 0 1752
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3272 1487 33 0 0 1752
in 8447.90 seconds
Image has 1487 counts for 0.1760 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.evt
Total Good Bad: Region Time Phase Cut
3272 1765 33 0 0 1474
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3272 1765 33 0 0 1474
in 8447.90 seconds
Image has 1765 counts for 0.2089 counts/sec
Command not found; type ? for a command listing
!ad83069000g300170m:ASCA >
!ad83069000g300170m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83069000g300170m:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!ad83069000g300170m:ASCA > read events ad83069000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!ad83069000g300170m:ASCA-GIS3-PH > set image sky
!ad83069000g300170m:ASCA-GIS3-PH > filter region corner_point.reg
!ad83069000g300170m:ASCA-GIS3-PH > extract image
!ad83069000g300170m:ASCA-GIS3-PH > save image outfile=ad83069000g300170m.img
Wrote image to file ad83069000g300170m.img
!ad83069000g300170m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad83069000g300170m:ASCA-GIS3-PH > extract image
!ad83069000g300170m:ASCA-GIS3-PH > save image outfile=ad83069000g300170m_lo.img
Wrote image to file ad83069000g300170m_lo.img
!ad83069000g300170m:ASCA-GIS3-PH > clear pha_cut
!ad83069000g300170m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad83069000g300170m:ASCA-GIS3-PH > extract image
!ad83069000g300170m:ASCA-GIS3-PH > save image outfile=ad83069000g300170m_hi.img
Wrote image to file ad83069000g300170m_hi.img
!ad83069000g300170m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad83069000g300270h.expo
ASCAEXPO_V0.9b
reading data file: ad83069000g300270h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa950717_0421.1830
making an exposure map...
Aspect RA/DEC/ROLL : 24.4251 -12.9141 290.4586
Mean RA/DEC/ROLL : 24.4193 -12.9110 290.4586
Pnt RA/DEC/ROLL : 24.4314 -12.9153 290.4586
Image rebin factor : 1
Attitude Records : 30074
GTI intervals : 54
Total GTI (secs) : 9114.174
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1500.0107422 1500.0107422
20 Percent Complete: Total/live time: 2840.0415039 2840.0415039
30 Percent Complete: Total/live time: 2840.0415039 2840.0415039
40 Percent Complete: Total/live time: 4606.0341797 4606.0341797
50 Percent Complete: Total/live time: 4924.1591797 4924.1591797
60 Percent Complete: Total/live time: 5717.0302734 5717.0302734
70 Percent Complete: Total/live time: 7440.1728516 7440.1728516
80 Percent Complete: Total/live time: 7440.1728516 7440.1728516
90 Percent Complete: Total/live time: 9114.1728516 9114.1728516
100 Percent Complete: Total/live time: 9114.1728516 9114.1728516
Number of attitude steps used: 19
Number of attitude steps avail: 24256
Mean RA/DEC pixel offset: 2.0664 -1.8679
writing expo file: ad83069000g300270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83069000g300270h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83069000g300270h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH HIGH 17/07/95 05:15:42 0.91E+04 3580 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.evt
Total Good Bad: Region Time Phase Cut
3580 3545 35 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3580 3545 35 0 0 0
in 9114.17 seconds
Image has 3545 counts for 0.3890 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.evt
Total Good Bad: Region Time Phase Cut
3580 1668 35 0 0 1877
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3580 1668 35 0 0 1877
in 9114.17 seconds
Image has 1668 counts for 0.1830 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.evt
Total Good Bad: Region Time Phase Cut
3580 1886 35 0 0 1659
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3580 1886 35 0 0 1659
in 9114.17 seconds
Image has 1886 counts for 0.2069 counts/sec
Command not found; type ? for a command listing
!ad83069000g300270h:ASCA >
!ad83069000g300270h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83069000g300270h:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!ad83069000g300270h:ASCA > read events ad83069000g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!ad83069000g300270h:ASCA-GIS3-PH > set image sky
!ad83069000g300270h:ASCA-GIS3-PH > filter region corner_point.reg
!ad83069000g300270h:ASCA-GIS3-PH > extract image
!ad83069000g300270h:ASCA-GIS3-PH > save image outfile=ad83069000g300270h.img
Wrote image to file ad83069000g300270h.img
!ad83069000g300270h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad83069000g300270h:ASCA-GIS3-PH > extract image
!ad83069000g300270h:ASCA-GIS3-PH > save image outfile=ad83069000g300270h_lo.img
Wrote image to file ad83069000g300270h_lo.img
!ad83069000g300270h:ASCA-GIS3-PH > clear pha_cut
!ad83069000g300270h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad83069000g300270h:ASCA-GIS3-PH > extract image
!ad83069000g300270h:ASCA-GIS3-PH > save image outfile=ad83069000g300270h_hi.img
Wrote image to file ad83069000g300270h_hi.img
!ad83069000g300270h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad83069000s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad83069000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa950717_0421.1830
making an exposure map...
Aspect RA/DEC/ROLL : 24.4251 -12.9141 290.4611
Mean RA/DEC/ROLL : 24.4078 -12.9283 290.4611
Pnt RA/DEC/ROLL : 24.4431 -12.8979 290.4611
Image rebin factor : 4
Attitude Records : 30074
Hot Pixels : 223
GTI intervals : 50
Total GTI (secs) : 8473.056
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1376.0000000 1376.0000000
20 Percent Complete: Total/live time: 2624.0000000 2624.0000000
30 Percent Complete: Total/live time: 3005.7175293 3005.7175293
40 Percent Complete: Total/live time: 4433.8027344 4433.8027344
50 Percent Complete: Total/live time: 4433.8027344 4433.8027344
60 Percent Complete: Total/live time: 5489.6157227 5489.6157227
70 Percent Complete: Total/live time: 6354.9062500 6354.9062500
80 Percent Complete: Total/live time: 8473.0546875 8473.0546875
100 Percent Complete: Total/live time: 8473.0546875 8473.0546875
Number of attitude steps used: 19
Number of attitude steps avail: 21494
Mean RA/DEC pixel offset: -33.0822 -88.6797
writing expo file: ad83069000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83069000s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83069000s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.85E+04 1861 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000102h.evt
Total Good Bad: Region Time Phase Cut
1861 1861 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1861 1861 0 0 0 0
in 8473.05 seconds
Image has 1861 counts for 0.2196 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000102h.evt
Total Good Bad: Region Time Phase Cut
1861 1240 0 0 0 621
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1861 1240 0 0 0 621
in 8473.05 seconds
Image has 1240 counts for 0.1463 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000102h.evt
Total Good Bad: Region Time Phase Cut
1861 621 0 0 0 1240
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1861 621 0 0 0 1240
in 8473.05 seconds
Image has 621 counts for 7.3291E-02 counts/sec
Command not found; type ? for a command listing
!ad83069000s000102h:ASCA >
!ad83069000s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83069000s000102h:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!ad83069000s000102h:ASCA > read events ad83069000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!ad83069000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad83069000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad83069000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad83069000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad83069000s000102h.img
Wrote image to file ad83069000s000102h.img
!ad83069000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad83069000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad83069000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad83069000s000102h_lo.img
Wrote image to file ad83069000s000102h_lo.img
!ad83069000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad83069000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad83069000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad83069000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad83069000s000102h_hi.img
Wrote image to file ad83069000s000102h_hi.img
!ad83069000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad83069000s000202m.expo
ASCAEXPO_V0.9b
reading data file: ad83069000s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa950717_0421.1830
making an exposure map...
Aspect RA/DEC/ROLL : 24.4251 -12.9141 290.4612
Mean RA/DEC/ROLL : 24.4081 -12.9283 290.4612
Pnt RA/DEC/ROLL : 24.4581 -12.8715 290.4612
Image rebin factor : 4
Attitude Records : 30074
Hot Pixels : 219
GTI intervals : 25
Total GTI (secs) : 8884.535
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1985.7253418 1985.7253418
20 Percent Complete: Total/live time: 1985.7253418 1985.7253418
30 Percent Complete: Total/live time: 2807.6601562 2807.6601562
40 Percent Complete: Total/live time: 4019.4096680 4019.4096680
50 Percent Complete: Total/live time: 4685.1596680 4685.1596680
60 Percent Complete: Total/live time: 5448.8061523 5448.8061523
70 Percent Complete: Total/live time: 7640.7900391 7640.7900391
80 Percent Complete: Total/live time: 7640.7900391 7640.7900391
90 Percent Complete: Total/live time: 8340.5351562 8340.5351562
100 Percent Complete: Total/live time: 8884.5351562 8884.5351562
Number of attitude steps used: 24
Number of attitude steps avail: 10210
Mean RA/DEC pixel offset: -33.7428 -87.8223
writing expo file: ad83069000s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83069000s000202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83069000s000202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT MEDIUM 17/07/95 04:21:18 0.89E+04 2383 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000202m.evt
Total Good Bad: Region Time Phase Cut
2383 2383 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2383 2383 0 0 0 0
in 8884.53 seconds
Image has 2383 counts for 0.2682 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000202m.evt
Total Good Bad: Region Time Phase Cut
2383 998 0 0 0 1385
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2383 998 0 0 0 1385
in 8884.53 seconds
Image has 998 counts for 0.1123 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000202m.evt
Total Good Bad: Region Time Phase Cut
2383 1385 0 0 0 998
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2383 1385 0 0 0 998
in 8884.53 seconds
Image has 1385 counts for 0.1559 counts/sec
Command not found; type ? for a command listing
!ad83069000s000202m:ASCA >
!ad83069000s000202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83069000s000202m:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!ad83069000s000202m:ASCA > read events ad83069000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!ad83069000s000202m:ASCA-SIS0-BRIGHT > set image sky
!ad83069000s000202m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad83069000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad83069000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad83069000s000202m.img
Wrote image to file ad83069000s000202m.img
!ad83069000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad83069000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad83069000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad83069000s000202m_lo.img
Wrote image to file ad83069000s000202m_lo.img
!ad83069000s000202m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad83069000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad83069000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad83069000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad83069000s000202m_hi.img
Wrote image to file ad83069000s000202m_hi.img
!ad83069000s000202m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad83069000s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad83069000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa950717_0421.1830
making an exposure map...
Aspect RA/DEC/ROLL : 24.4251 -12.9141 290.4576
Mean RA/DEC/ROLL : 24.4234 -12.9237 290.4576
Pnt RA/DEC/ROLL : 24.4275 -12.9026 290.4576
Image rebin factor : 4
Attitude Records : 30074
Hot Pixels : 351
GTI intervals : 55
Total GTI (secs) : 8500.505
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1408.0000000 1408.0000000
20 Percent Complete: Total/live time: 2656.0000000 2656.0000000
30 Percent Complete: Total/live time: 2656.0000000 2656.0000000
40 Percent Complete: Total/live time: 4485.6279297 4485.6279297
50 Percent Complete: Total/live time: 4485.6279297 4485.6279297
60 Percent Complete: Total/live time: 5205.5317383 5205.5317383
70 Percent Complete: Total/live time: 6412.4501953 6412.4501953
80 Percent Complete: Total/live time: 7164.8715820 7164.8715820
90 Percent Complete: Total/live time: 8500.5048828 8500.5048828
100 Percent Complete: Total/live time: 8500.5048828 8500.5048828
Number of attitude steps used: 21
Number of attitude steps avail: 21420
Mean RA/DEC pixel offset: -37.8391 -20.4349
writing expo file: ad83069000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83069000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83069000s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.85E+04 1664 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100102h.evt
Total Good Bad: Region Time Phase Cut
1664 1664 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1664 1664 0 0 0 0
in 8500.50 seconds
Image has 1664 counts for 0.1958 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100102h.evt
Total Good Bad: Region Time Phase Cut
1664 1017 0 0 0 647
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1664 1017 0 0 0 647
in 8500.50 seconds
Image has 1017 counts for 0.1196 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100102h.evt
Total Good Bad: Region Time Phase Cut
1664 647 0 0 0 1017
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1664 647 0 0 0 1017
in 8500.50 seconds
Image has 647 counts for 7.6113E-02 counts/sec
Command not found; type ? for a command listing
!ad83069000s100102h:ASCA >
!ad83069000s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83069000s100102h:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!ad83069000s100102h:ASCA > read events ad83069000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!ad83069000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad83069000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad83069000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad83069000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad83069000s100102h.img
Wrote image to file ad83069000s100102h.img
!ad83069000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad83069000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad83069000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad83069000s100102h_lo.img
Wrote image to file ad83069000s100102h_lo.img
!ad83069000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad83069000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad83069000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad83069000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad83069000s100102h_hi.img
Wrote image to file ad83069000s100102h_hi.img
!ad83069000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad83069000s100202m.expo
ASCAEXPO_V0.9b
reading data file: ad83069000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa950717_0421.1830
making an exposure map...
Aspect RA/DEC/ROLL : 24.4251 -12.9141 290.4576
Mean RA/DEC/ROLL : 24.4237 -12.9238 290.4576
Pnt RA/DEC/ROLL : 24.4425 -12.8761 290.4576
Image rebin factor : 4
Attitude Records : 30074
Hot Pixels : 365
GTI intervals : 28
Total GTI (secs) : 8774.910
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1953.7253418 1953.7253418
20 Percent Complete: Total/live time: 1953.7253418 1953.7253418
30 Percent Complete: Total/live time: 2775.6601562 2775.6601562
40 Percent Complete: Total/live time: 3987.4096680 3987.4096680
50 Percent Complete: Total/live time: 4685.1596680 4685.1596680
60 Percent Complete: Total/live time: 5384.8061523 5384.8061523
70 Percent Complete: Total/live time: 7576.7900391 7576.7900391
80 Percent Complete: Total/live time: 7576.7900391 7576.7900391
90 Percent Complete: Total/live time: 8230.9111328 8230.9111328
100 Percent Complete: Total/live time: 8774.9111328 8774.9111328
Number of attitude steps used: 24
Number of attitude steps avail: 10218
Mean RA/DEC pixel offset: -38.0019 -18.9650
writing expo file: ad83069000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad83069000s100202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad83069000s100202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT MEDIUM 17/07/95 04:21:18 0.88E+04 2434 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100202m.evt
Total Good Bad: Region Time Phase Cut
2434 2434 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2434 2434 0 0 0 0
in 8774.91 seconds
Image has 2434 counts for 0.2774 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100202m.evt
Total Good Bad: Region Time Phase Cut
2434 1011 0 0 0 1423
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2434 1011 0 0 0 1423
in 8774.91 seconds
Image has 1011 counts for 0.1152 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100202m.evt
Total Good Bad: Region Time Phase Cut
2434 1423 0 0 0 1011
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2434 1423 0 0 0 1011
in 8774.91 seconds
Image has 1423 counts for 0.1622 counts/sec
Command not found; type ? for a command listing
!ad83069000s100202m:ASCA >
!ad83069000s100202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad83069000s100202m:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!ad83069000s100202m:ASCA > read events ad83069000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!ad83069000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad83069000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad83069000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad83069000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad83069000s100202m.img
Wrote image to file ad83069000s100202m.img
!ad83069000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad83069000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad83069000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad83069000s100202m_lo.img
Wrote image to file ad83069000s100202m_lo.img
!ad83069000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad83069000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad83069000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad83069000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad83069000s100202m_hi.img
Wrote image to file ad83069000s100202m_hi.img
!ad83069000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad83069000s000102h.expo ad83069000s000202m.expo ad83069000s100102h.expo ad83069000s100202m.expo-> Summing the following images to produce ad83069000sis32002_all.totsky
ad83069000s000102h.img ad83069000s000202m.img ad83069000s100102h.img ad83069000s100202m.img-> Summing the following images to produce ad83069000sis32002_lo.totsky
ad83069000s000102h_lo.img ad83069000s000202m_lo.img ad83069000s100102h_lo.img ad83069000s100202m_lo.img-> Summing the following images to produce ad83069000sis32002_hi.totsky
ad83069000s000102h_hi.img ad83069000s000202m_hi.img ad83069000s100102h_hi.img ad83069000s100202m_hi.img-> Running XIMAGE to create ad83069000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad83069000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 7.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 7 min: 0 ![2]XIMAGE> read/exp_map ad83069000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 577.217 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 577 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 12.0000 12 0 ![9]XIMAGE> exit-> Summing gis images
ad83069000g200170m.expo ad83069000g200270h.expo ad83069000g300170m.expo ad83069000g300270h.expo-> Summing the following images to produce ad83069000gis25670_all.totsky
ad83069000g200170m.img ad83069000g200270h.img ad83069000g300170m.img ad83069000g300270h.img-> Summing the following images to produce ad83069000gis25670_lo.totsky
ad83069000g200170m_lo.img ad83069000g200270h_lo.img ad83069000g300170m_lo.img ad83069000g300270h_lo.img-> Summing the following images to produce ad83069000gis25670_hi.totsky
ad83069000g200170m_hi.img ad83069000g200270h_hi.img ad83069000g300170m_hi.img ad83069000g300270h_hi.img-> Running XIMAGE to create ad83069000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad83069000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 11.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 11 min: 0 ![2]XIMAGE> read/exp_map ad83069000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 586.003 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 586 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 16.0000 16 0 ![9]XIMAGE> exit
116 151 0.000183288 19 15 16.9587 138 109 0.000155858 27 16 14.1252-> Smoothing ad83069000gis25670_hi.totsky with ad83069000gis25670.totexpo
117 150 8.53239e-05 18 17 14.1242 138 110 6.71214e-05 26 18 10.687-> Smoothing ad83069000gis25670_lo.totsky with ad83069000gis25670.totexpo
138 109 8.98745e-05 27 15 19.5277 118 150 7.8498e-05 18 18 16.6152-> Determining extraction radii
116 151 19 T 138 109 24 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad83069000gis25670.src
180 114 6.01479e-05 165 35 9.2775-> Smoothing ad83069000sis32002_hi.totsky with ad83069000sis32002.totexpo
176 108 2.17489e-05 161 23 5.1361-> Smoothing ad83069000sis32002_lo.totsky with ad83069000sis32002.totexpo
178 114 3.95194e-05 163 33 17.7946-> Determining extraction radii
180 114 38 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad83069000sis32002.src
The sum of the selected column is 965.00000 The mean of the selected column is 482.50000 The standard deviation of the selected column is 2.1213203 The minimum of selected column is 481.00000 The maximum of selected column is 484.00000 The number of points used in calculation is 2-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 910.00000 The mean of the selected column is 455.00000 The standard deviation of the selected column is 0. The minimum of selected column is 455.00000 The maximum of selected column is 455.00000 The number of points used in calculation is 2-> Converting (720.0,456.0,2.0) to s1 detector coordinates
The sum of the selected column is 477.00000 The mean of the selected column is 477.00000 The standard deviation of the selected column is undefined The minimum of selected column is 477.00000 The maximum of selected column is 477.00000 The number of points used in calculation is 1-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 491.00000 The mean of the selected column is 491.00000 The standard deviation of the selected column is undefined The minimum of selected column is 491.00000 The maximum of selected column is 491.00000 The number of points used in calculation is 1-> Converting (116.0,151.0,2.0) to g2 detector coordinates
The sum of the selected column is 6172.0000 The mean of the selected column is 140.27273 The standard deviation of the selected column is 1.1883864 The minimum of selected column is 138.00000 The maximum of selected column is 142.00000 The number of points used in calculation is 44-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 6471.0000 The mean of the selected column is 147.06818 The standard deviation of the selected column is 1.0206639 The minimum of selected column is 145.00000 The maximum of selected column is 149.00000 The number of points used in calculation is 44-> Converting (138.0,109.0,2.0) to g2 detector coordinates
The sum of the selected column is 2822.0000 The mean of the selected column is 108.53846 The standard deviation of the selected column is 1.2721877 The minimum of selected column is 106.00000 The maximum of selected column is 111.00000 The number of points used in calculation is 26-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2916.0000 The mean of the selected column is 112.15385 The standard deviation of the selected column is 1.1896994 The minimum of selected column is 110.00000 The maximum of selected column is 114.00000 The number of points used in calculation is 26-> Converting (116.0,151.0,2.0) to g3 detector coordinates
The sum of the selected column is 5847.0000 The mean of the selected column is 146.17500 The standard deviation of the selected column is 1.1958797 The minimum of selected column is 144.00000 The maximum of selected column is 149.00000 The number of points used in calculation is 40-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 5909.0000 The mean of the selected column is 147.72500 The standard deviation of the selected column is 1.0618682 The minimum of selected column is 146.00000 The maximum of selected column is 150.00000 The number of points used in calculation is 40-> Converting (138.0,109.0,2.0) to g3 detector coordinates
The sum of the selected column is 5169.0000 The mean of the selected column is 114.86667 The standard deviation of the selected column is 1.0574412 The minimum of selected column is 113.00000 The maximum of selected column is 117.00000 The number of points used in calculation is 45-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 5067.0000 The mean of the selected column is 112.60000 The standard deviation of the selected column is 1.0313275 The minimum of selected column is 111.00000 The maximum of selected column is 115.00000 The number of points used in calculation is 45
1 ad83069000s000102h.evt 4244 1 ad83069000s000202m.evt 4244-> Fetching SIS0_NOTCHIP2.1
ad83069000s000102h.evt ad83069000s000202m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.85E+04 1861 1100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.85E+04 1861 1100
2 A222 BRIGHT MEDIUM 17/07/95 04:21:18 0.89E+04 2383 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000102h.evt
Total Good Bad: Region Time Phase Cut
1861 811 1050 0 0 0
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000202m.evt
Total Good Bad: Region Time Phase Cut
2383 928 1455 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4244 1739 2505 0 0 0
in 17357.59 seconds
Spectrum has 1739 counts for 0.1002 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 17358. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.59082E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad83069000s010102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000102h.evt
Total Good Bad: Region Time Phase Cut
1861 811 1050 0 0 0
Writing events file
811 events written to the output file
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000202m.evt
Total Good Bad: Region Time Phase Cut
2383 928 1455 0 0 0
Writing events file
1739 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4244 1739 2505 0 0 0
in 17357.59 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad83069000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad83069000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad83069000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad83069000s010102_1.pi group=yes
Wrote spectrum to ad83069000s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad83069000s010102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 17358. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.59082E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 22 are grouped by a factor 5 ... 23 - 31 are grouped by a factor 3 ... 32 - 43 are grouped by a factor 2 ... 44 - 44 are single channels ... 45 - 54 are grouped by a factor 2 ... 55 - 60 are grouped by a factor 3 ... 61 - 62 are grouped by a factor 2 ... 63 - 66 are grouped by a factor 4 ... 67 - 71 are grouped by a factor 5 ... 72 - 77 are grouped by a factor 6 ... 78 - 82 are grouped by a factor 5 ... 83 - 96 are grouped by a factor 7 ... 97 - 106 are grouped by a factor 10 ... 107 - 115 are grouped by a factor 9 ... 116 - 133 are grouped by a factor 18 ... 134 - 148 are grouped by a factor 15 ... 149 - 173 are grouped by a factor 25 ... 174 - 216 are grouped by a factor 43 ... 217 - 312 are grouped by a factor 96 ... 313 - 460 are grouped by a factor 148 ... 461 - 499 are grouped by a factor 39 ... --------------------------------------------- ... ...... exiting, changes written to file : ad83069000s010102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad83069000s010102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 40 by 40 bins
expanded to 40 by 40 bins
First WMAP bin is at detector pixel 328 304
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 52.900 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.71900E+03
Weighted mean angle from optical axis = 5.490 arcmin
-> Standard Output From STOOL group_event_files:1 ad83069000s000112h.evt 1941-> SIS0_NOTCHIP2.1 already present in current directory
ad83069000s000112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT2 HIGH 17/07/95 05:12:18 0.85E+04 1941 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000112h.evt
Total Good Bad: Region Time Phase Cut
1941 827 1114 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1941 827 1114 0 0 0
in 8473.05 seconds
Spectrum has 827 counts for 9.7604E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 8473.1 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.59082E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad83069000s010212_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000112h.evt
Total Good Bad: Region Time Phase Cut
1941 827 1114 0 0 0
Writing events file
827 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1941 827 1114 0 0 0
in 8473.05 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad83069000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad83069000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad83069000s010212_1.pi group=yes
Wrote spectrum to ad83069000s010212_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad83069000s010212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 8473.1 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.59082E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 48 are grouped by a factor 23 ... 49 - 58 are grouped by a factor 10 ... 59 - 67 are grouped by a factor 9 ... 68 - 73 are grouped by a factor 6 ... 74 - 78 are grouped by a factor 5 ... 79 - 85 are grouped by a factor 7 ... 86 - 90 are grouped by a factor 5 ... 91 - 96 are grouped by a factor 6 ... 97 - 103 are grouped by a factor 7 ... 104 - 109 are grouped by a factor 6 ... 110 - 118 are grouped by a factor 9 ... 119 - 128 are grouped by a factor 10 ... 129 - 148 are grouped by a factor 20 ... 149 - 171 are grouped by a factor 23 ... 172 - 205 are grouped by a factor 34 ... 206 - 243 are grouped by a factor 38 ... 244 - 297 are grouped by a factor 54 ... 298 - 513 are grouped by a factor 216 ... 514 - 1013 are grouped by a factor 500 ... 1014 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad83069000s010212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad83069000s010212_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 40 by 40 bins
expanded to 40 by 40 bins
First WMAP bin is at detector pixel 328 304
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 52.900 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 8.17000E+02
Weighted mean angle from optical axis = 5.456 arcmin
-> Standard Output From STOOL group_event_files:1 ad83069000s100102h.evt 4098 1 ad83069000s100202m.evt 4098-> Fetching SIS1_NOTCHIP0.1
ad83069000s100102h.evt ad83069000s100202m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.85E+04 1664 0011
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.85E+04 1664 0011
2 A222 BRIGHT MEDIUM 17/07/95 04:21:18 0.88E+04 2434 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100102h.evt
Total Good Bad: Region Time Phase Cut
1664 736 928 0 0 0
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100202m.evt
Total Good Bad: Region Time Phase Cut
2434 807 1627 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4098 1543 2555 0 0 0
in 17275.41 seconds
Spectrum has 1543 counts for 8.9318E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 17275. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.41895E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad83069000s110102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100102h.evt
Total Good Bad: Region Time Phase Cut
1664 736 928 0 0 0
Writing events file
736 events written to the output file
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100202m.evt
Total Good Bad: Region Time Phase Cut
2434 807 1627 0 0 0
Writing events file
1543 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4098 1543 2555 0 0 0
in 17275.41 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS1-BRIGHT > read events ad83069000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad83069000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad83069000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad83069000s110102_1.pi group=yes
Wrote spectrum to ad83069000s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad83069000s110102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 17275. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.41895E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 18 are grouped by a factor 6 ... 19 - 23 are grouped by a factor 5 ... 24 - 32 are grouped by a factor 3 ... 33 - 48 are grouped by a factor 2 ... 49 - 60 are grouped by a factor 3 ... 61 - 65 are grouped by a factor 5 ... 66 - 77 are grouped by a factor 6 ... 78 - 86 are grouped by a factor 9 ... 87 - 96 are grouped by a factor 10 ... 97 - 107 are grouped by a factor 11 ... 108 - 119 are grouped by a factor 12 ... 120 - 133 are grouped by a factor 14 ... 134 - 161 are grouped by a factor 28 ... 162 - 190 are grouped by a factor 29 ... 191 - 243 are grouped by a factor 53 ... 244 - 353 are grouped by a factor 110 ... 354 - 447 are grouped by a factor 94 ... 448 - 452 are grouped by a factor 5 ... --------------------------------------------- ... ...... exiting, changes written to file : ad83069000s110102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad83069000s110102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 39 by 36 bins
expanded to 39 by 36 bins
First WMAP bin is at detector pixel 328 344
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 50.920 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.50700E+03
Weighted mean angle from optical axis = 8.327 arcmin
-> Standard Output From STOOL group_event_files:1 ad83069000s100112h.evt 1744-> SIS1_NOTCHIP0.1 already present in current directory
ad83069000s100112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT2 HIGH 17/07/95 05:12:18 0.85E+04 1744 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100112h.evt
Total Good Bad: Region Time Phase Cut
1744 748 996 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1744 748 996 0 0 0
in 8500.50 seconds
Spectrum has 748 counts for 8.7995E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 8500.5 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 4.41895E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad83069000s110212_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100112h.evt
Total Good Bad: Region Time Phase Cut
1744 748 996 0 0 0
Writing events file
748 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1744 748 996 0 0 0
in 8500.50 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad83069000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad83069000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad83069000s110212_1.pi group=yes
Wrote spectrum to ad83069000s110212_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad83069000s110212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 8500.5 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 4.41895E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 46 are grouped by a factor 21 ... 47 - 59 are grouped by a factor 13 ... 60 - 66 are grouped by a factor 7 ... 67 - 71 are grouped by a factor 5 ... 72 - 78 are grouped by a factor 7 ... 79 - 84 are grouped by a factor 6 ... 85 - 98 are grouped by a factor 7 ... 99 - 109 are grouped by a factor 11 ... 110 - 121 are grouped by a factor 12 ... 122 - 142 are grouped by a factor 21 ... 143 - 169 are grouped by a factor 27 ... 170 - 207 are grouped by a factor 38 ... 208 - 244 are grouped by a factor 37 ... 245 - 328 are grouped by a factor 84 ... --------------------------------------------- ... ...... exiting, changes written to file : ad83069000s110212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad83069000s110212_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 39 by 36 bins
expanded to 39 by 36 bins
First WMAP bin is at detector pixel 328 344
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 50.920 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 7.29000E+02
Weighted mean angle from optical axis = 8.375 arcmin
-> Standard Output From STOOL group_event_files:1 ad83069000g200170m.evt 6522 1 ad83069000g200270h.evt 6522-> GIS2_REGION256.4 already present in current directory
ad83069000g200170m.evt ad83069000g200270h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.85E+04 3162 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.85E+04 3162 1024
2 A222 PH HIGH 17/07/95 05:15:40 0.91E+04 3360 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.evt
Total Good Bad: Region Time Phase Cut
3162 500 2662 0 0 0
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.evt
Total Good Bad: Region Time Phase Cut
3360 579 2781 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6522 1079 5443 0 0 0
in 17598.07 seconds
Spectrum has 1079 counts for 6.1314E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 17598. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.83258E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad83069000g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > read events ad83069000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad83069000g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad83069000g210170_1.pi group=yes
Wrote spectrum to ad83069000g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad83069000g210170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad83069000g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 17598. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 1.83258E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 58 are grouped by a factor 59 ... 59 - 72 are grouped by a factor 14 ... 73 - 98 are grouped by a factor 13 ... 99 - 105 are grouped by a factor 7 ... 106 - 113 are grouped by a factor 8 ... 114 - 119 are grouped by a factor 6 ... 120 - 135 are grouped by a factor 8 ... 136 - 144 are grouped by a factor 9 ... 145 - 151 are grouped by a factor 7 ... 152 - 162 are grouped by a factor 11 ... 163 - 171 are grouped by a factor 9 ... 172 - 199 are grouped by a factor 14 ... 200 - 216 are grouped by a factor 17 ... 217 - 236 are grouped by a factor 20 ... 237 - 261 are grouped by a factor 25 ... 262 - 282 are grouped by a factor 21 ... 283 - 316 are grouped by a factor 34 ... 317 - 354 are grouped by a factor 38 ... 355 - 403 are grouped by a factor 49 ... 404 - 447 are grouped by a factor 44 ... 448 - 501 are grouped by a factor 54 ... 502 - 604 are grouped by a factor 103 ... 605 - 876 are grouped by a factor 272 ... 877 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad83069000g210170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 39 by 39 bins
expanded to 64 by 64 bins
First WMAP bin is at detector pixel 110 117
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 72.432 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.07900E+03
Weighted mean angle from optical axis = 5.040 arcmin
-> Extracting ad83069000g210170_2.pi from ad83069000g225670_2.reg and:ad83069000g200170m.evt ad83069000g200270h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.85E+04 3162 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.85E+04 3162 1024
2 A222 PH HIGH 17/07/95 05:15:40 0.91E+04 3360 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.evt
Total Good Bad: Region Time Phase Cut
3162 550 2612 0 0 0
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.evt
Total Good Bad: Region Time Phase Cut
3360 577 2783 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6522 1127 5395 0 0 0
in 17598.07 seconds
Spectrum has 1127 counts for 6.4041E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 17598. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad83069000g210170_2.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > read events ad83069000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad83069000g225670_2.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad83069000g210170_2.pi group=yes
Wrote spectrum to ad83069000g210170_2.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad83069000g210170_2.pi for dead time... read all the files from deadlist.tmp-> Grouping ad83069000g210170_2.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 17598. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 58 are grouped by a factor 59 ... 59 - 74 are grouped by a factor 16 ... 75 - 85 are grouped by a factor 11 ... 86 - 93 are grouped by a factor 8 ... 94 - 100 are grouped by a factor 7 ... 101 - 110 are grouped by a factor 10 ... 111 - 118 are grouped by a factor 8 ... 119 - 123 are grouped by a factor 5 ... 124 - 130 are grouped by a factor 7 ... 131 - 136 are grouped by a factor 6 ... 137 - 144 are grouped by a factor 8 ... 145 - 156 are grouped by a factor 12 ... 157 - 164 are grouped by a factor 8 ... 165 - 174 are grouped by a factor 10 ... 175 - 183 are grouped by a factor 9 ... 184 - 199 are grouped by a factor 16 ... 200 - 222 are grouped by a factor 23 ... 223 - 239 are grouped by a factor 17 ... 240 - 287 are grouped by a factor 24 ... 288 - 317 are grouped by a factor 30 ... 318 - 353 are grouped by a factor 36 ... 354 - 405 are grouped by a factor 52 ... 406 - 450 are grouped by a factor 45 ... 451 - 502 are grouped by a factor 52 ... 503 - 648 are grouped by a factor 146 ... 649 - 981 are grouped by a factor 333 ... 982 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad83069000g210170_2.pi ** grppha 2.6.0 completed successfully-> gis2v4_0.rmf already present in current directory
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 47 50
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.12700E+03
Weighted mean angle from optical axis = 7.636 arcmin
-> Standard Output From STOOL group_event_files:1 ad83069000g300170m.evt 6852 1 ad83069000g300270h.evt 6852-> GIS3_REGION256.4 already present in current directory
ad83069000g300170m.evt ad83069000g300270h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.84E+04 3272 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.84E+04 3272 1024
2 A222 PH HIGH 17/07/95 05:15:42 0.91E+04 3580 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.evt
Total Good Bad: Region Time Phase Cut
3272 497 2775 0 0 0
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.evt
Total Good Bad: Region Time Phase Cut
3580 558 3022 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6852 1055 5797 0 0 0
in 17562.07 seconds
Spectrum has 1055 counts for 6.0073E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 17562. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 1.83258E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad83069000g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > read events ad83069000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad83069000g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad83069000g310170_1.pi group=yes
Wrote spectrum to ad83069000g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad83069000g310170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad83069000g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 17562. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 1.83258E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 64 are grouped by a factor 65 ... 65 - 77 are grouped by a factor 13 ... 78 - 85 are grouped by a factor 8 ... 86 - 96 are grouped by a factor 11 ... 97 - 104 are grouped by a factor 8 ... 105 - 113 are grouped by a factor 9 ... 114 - 120 are grouped by a factor 7 ... 121 - 132 are grouped by a factor 6 ... 133 - 140 are grouped by a factor 8 ... 141 - 146 are grouped by a factor 6 ... 147 - 153 are grouped by a factor 7 ... 154 - 163 are grouped by a factor 10 ... 164 - 175 are grouped by a factor 12 ... 176 - 183 are grouped by a factor 8 ... 184 - 202 are grouped by a factor 19 ... 203 - 223 are grouped by a factor 21 ... 224 - 248 are grouped by a factor 25 ... 249 - 278 are grouped by a factor 30 ... 279 - 299 are grouped by a factor 21 ... 300 - 332 are grouped by a factor 33 ... 333 - 387 are grouped by a factor 55 ... 388 - 455 are grouped by a factor 68 ... 456 - 542 are grouped by a factor 87 ... 543 - 684 are grouped by a factor 142 ... 685 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad83069000g310170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 39 by 39 bins
expanded to 64 by 64 bins
First WMAP bin is at detector pixel 116 118
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 72.432 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.05500E+03
Weighted mean angle from optical axis = 7.675 arcmin
-> Extracting ad83069000g310170_2.pi from ad83069000g325670_2.reg and:ad83069000g300170m.evt ad83069000g300270h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.84E+04 3272 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.84E+04 3272 1024
2 A222 PH HIGH 17/07/95 05:15:42 0.91E+04 3580 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.evt
Total Good Bad: Region Time Phase Cut
3272 600 2672 0 0 0
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.evt
Total Good Bad: Region Time Phase Cut
3580 692 2888 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6852 1292 5560 0 0 0
in 17562.07 seconds
Spectrum has 1292 counts for 7.3568E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 17562. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad83069000g310170_2.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > read events ad83069000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad83069000g325670_2.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad83069000g310170_2.pi group=yes
Wrote spectrum to ad83069000g310170_2.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad83069000g310170_2.pi for dead time... read all the files from deadlist.tmp-> Grouping ad83069000g310170_2.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 17562. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 49 are grouped by a factor 50 ... 50 - 67 are grouped by a factor 18 ... 68 - 79 are grouped by a factor 12 ... 80 - 89 are grouped by a factor 10 ... 90 - 96 are grouped by a factor 7 ... 97 - 106 are grouped by a factor 10 ... 107 - 113 are grouped by a factor 7 ... 114 - 119 are grouped by a factor 6 ... 120 - 124 are grouped by a factor 5 ... 125 - 131 are grouped by a factor 7 ... 132 - 149 are grouped by a factor 6 ... 150 - 163 are grouped by a factor 7 ... 164 - 172 are grouped by a factor 9 ... 173 - 180 are grouped by a factor 8 ... 181 - 191 are grouped by a factor 11 ... 192 - 201 are grouped by a factor 10 ... 202 - 221 are grouped by a factor 20 ... 222 - 240 are grouped by a factor 19 ... 241 - 263 are grouped by a factor 23 ... 264 - 287 are grouped by a factor 24 ... 288 - 313 are grouped by a factor 26 ... 314 - 346 are grouped by a factor 33 ... 347 - 389 are grouped by a factor 43 ... 390 - 417 are grouped by a factor 28 ... 418 - 469 are grouped by a factor 52 ... 470 - 551 are grouped by a factor 82 ... 552 - 656 are grouped by a factor 105 ... 657 - 895 are grouped by a factor 239 ... 896 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad83069000g310170_2.pi ** grppha 2.6.0 completed successfully-> gis3v4_0.rmf already present in current directory
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 53 51
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.29200E+03
Weighted mean angle from optical axis = 5.832 arcmin
-> Plotting ad83069000g210170_1_pi.ps from ad83069000g210170_1.pi
XSPEC 9.01 09:22:27 28-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83069000g210170_1.pi
Net count rate (cts/s) for file 1 6.1314E-02+/- 1.9815E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad83069000g210170_2_pi.ps from ad83069000g210170_2.pi
XSPEC 9.01 09:22:57 28-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83069000g210170_2.pi
Net count rate (cts/s) for file 1 6.4041E-02+/- 1.9420E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad83069000g310170_1_pi.ps from ad83069000g310170_1.pi
XSPEC 9.01 09:23:26 28-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83069000g310170_1.pi
Net count rate (cts/s) for file 1 6.0073E-02+/- 2.1107E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad83069000g310170_2_pi.ps from ad83069000g310170_2.pi
XSPEC 9.01 09:23:53 28-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83069000g310170_2.pi
Net count rate (cts/s) for file 1 7.3568E-02+/- 2.1412E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad83069000s010102_1_pi.ps from ad83069000s010102_1.pi
XSPEC 9.01 09:24:21 28-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83069000s010102_1.pi
Net count rate (cts/s) for file 1 0.1002 +/- 2.4087E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad83069000s010212_1_pi.ps from ad83069000s010212_1.pi
XSPEC 9.01 09:24:50 28-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83069000s010212_1.pi
Net count rate (cts/s) for file 1 9.7604E-02+/- 3.4510E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad83069000s110102_1_pi.ps from ad83069000s110102_1.pi
XSPEC 9.01 09:25:27 28-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83069000s110102_1.pi
Net count rate (cts/s) for file 1 8.9318E-02+/- 2.2819E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad83069000s110212_1_pi.ps from ad83069000s110212_1.pi
XSPEC 9.01 09:25:57 28-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad83069000s110212_1.pi
Net count rate (cts/s) for file 1 8.7995E-02+/- 3.2644E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.85E+04 1861 1100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.85E+04 1861 1100
2 A222 BRIGHT MEDIUM 17/07/95 04:21:18 0.89E+04 2383 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000102h.evt
Total Good Bad: Region Time Phase Cut
1861 811 1050 0 0 0
Writing events file
811 events written to the output file
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000202m.evt
Total Good Bad: Region Time Phase Cut
2383 928 1455 0 0 0
Writing events file
1739 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4244 1739 2505 0 0 0
in 17357.59 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS0-BRIGHT > read events ad83069000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad83069000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad83069000s000002_1.lc with binsize 499.068111996581
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT HIGH 17/07/95 04:21:18 0.17E+05 1739 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1739 1739 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1739 1739 0 0 0 0
in 17357.59 seconds
Fits light curve has 1739 counts for 0.1002 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS0-BRIGHT > set binsize 499.068111996581
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad83069000s000002_1.lc
Wrote FITS light curve to file ad83069000s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad83069000s000002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad83069000s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A222 Start Time (d) .... 9915 05:13:30.217
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9915 18:21:14.217
No. of Rows ....... 36 Bin Time (s) ...... 499.1
Right Ascension ... 2.4425E+01 Internal time sys.. Converted to TJD
Declination ....... -1.2914E+01 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 95 Newbins of 499.068 (s)
Intv 1 Start 9915 5:17:39
Ser.1 Avg 0.1040 Chisq 328.2 Var 0.2390E-02 Newbs. 36
Min 0.6110E-01 Max 0.3531 expVar 0.2622E-03 Bins 36
Results from Statistical Analysis
Newbin Integration Time (s).. 499.07
Interval Duration (s)........ 46912.
No. of Newbins .............. 36
Average (c/s) ............... 0.10402 +/- 0.27E-02
Standard Deviation (c/s)..... 0.48891E-01
Minimum (c/s)................ 0.61099E-01
Maximum (c/s)................ 0.35309
Variance ((c/s)**2).......... 0.23903E-02 +/- 0.57E-03
Expected Variance ((c/s)**2). 0.26217E-03 +/- 0.63E-04
Third Moment ((c/s)**3)...... 0.43560E-03
Average Deviation (c/s)...... 0.27022E-01
Skewness..................... 3.7274 +/- 0.41
Kurtosis..................... 16.002 +/- 0.82
RMS fractional variation..... 0.44349 +/- 0.60E-01
Chi-Square................... 328.23 dof 35
Chi-Square Prob of constancy. 0. (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.10073E-20 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 95 Newbins of 499.068 (s)
Intv 1 Start 9915 5:17:39
Ser.1 Avg 0.1040 Chisq 328.2 Var 0.2390E-02 Newbs. 36
Min 0.6110E-01 Max 0.3531 expVar 0.2622E-03 Bins 36
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Standard Error Output From FTOOL xronosNote: the following IEEE floating-point arithmetic exceptions occurred and were never cleared; see ieee_flags(3M): Inexact; Underflow; Sun's implementation of IEEE arithmetic is discussed in the Numerical Computation Guide.-> TIMEDEL=8.0000000000E+00 for ad83069000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.85E+04 1664 0011
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.85E+04 1664 0011
2 A222 BRIGHT MEDIUM 17/07/95 04:21:18 0.88E+04 2434 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100102h.evt
Total Good Bad: Region Time Phase Cut
1664 740 924 0 0 0
Writing events file
740 events written to the output file
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100202m.evt
Total Good Bad: Region Time Phase Cut
2434 809 1625 0 0 0
Writing events file
1549 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4098 1549 2549 0 0 0
in 17275.41 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS1-BRIGHT > read events ad83069000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS1-BRIGHT > filter region ad83069000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad83069000s100002_1.lc with binsize 557.631170388439
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT HIGH 17/07/95 04:21:18 0.17E+05 1549 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1549 1549 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1549 1549 0 0 0 0
in 17275.41 seconds
Fits light curve has 1549 counts for 8.9665E-02 counts/sec
Thresholding removed significant counts
Try exposure=0.0 on the extract command in xselect
or lcthresh=0.0 if running extractor stand-alone
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS1-BRIGHT > set binsize 557.631170388439
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad83069000s100002_1.lc
Wrote FITS light curve to file ad83069000s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad83069000s100002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad83069000s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A222 Start Time (d) .... 9915 05:13:30.217
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9915 18:21:14.217
No. of Rows ....... 33 Bin Time (s) ...... 557.6
Right Ascension ... 2.4425E+01 Internal time sys.. Converted to TJD
Declination ....... -1.2914E+01 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 85 Newbins of 557.631 (s)
Intv 1 Start 9915 5:18: 9
Ser.1 Avg 0.8799E-01 Chisq 87.67 Var 0.5349E-03 Newbs. 33
Min 0.5871E-01 Max 0.1903 expVar 0.2013E-03 Bins 33
Results from Statistical Analysis
Newbin Integration Time (s).. 557.63
Interval Duration (s)........ 46841.
No. of Newbins .............. 33
Average (c/s) ............... 0.87991E-01 +/- 0.25E-02
Standard Deviation (c/s)..... 0.23127E-01
Minimum (c/s)................ 0.58713E-01
Maximum (c/s)................ 0.19027
Variance ((c/s)**2).......... 0.53487E-03 +/- 0.13E-03
Expected Variance ((c/s)**2). 0.20134E-03 +/- 0.50E-04
Third Moment ((c/s)**3)...... 0.30490E-04
Average Deviation (c/s)...... 0.15628E-01
Skewness..................... 2.4648 +/- 0.43
Kurtosis..................... 8.9484 +/- 0.85
RMS fractional variation..... 0.20755 +/- 0.42E-01
Chi-Square................... 87.665 dof 32
Chi-Square Prob of constancy. 0.44579E-06 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.35468E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 85 Newbins of 557.631 (s)
Intv 1 Start 9915 5:18: 9
Ser.1 Avg 0.8799E-01 Chisq 87.67 Var 0.5349E-03 Newbs. 33
Min 0.5871E-01 Max 0.1903 expVar 0.2013E-03 Bins 33
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=5.0000000000E-01 for ad83069000g200170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.85E+04 3162 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.85E+04 3162 1024
2 A222 PH HIGH 17/07/95 05:15:40 0.91E+04 3360 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.evt
Total Good Bad: Region Time Phase Cut
3162 500 2662 0 0 0
Writing events file
500 events written to the output file
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.evt
Total Good Bad: Region Time Phase Cut
3360 579 2781 0 0 0
Writing events file
1079 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6522 1079 5443 0 0 0
in 17598.07 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > read events ad83069000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > filter region ad83069000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad83069000g200070_1.lc with binsize 815.48074926487
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.18E+05 1079 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1079 1079 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1079 1079 0 0 0 0
in 17598.07 seconds
Fits light curve has 1079 counts for 6.1314E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > set binsize 815.48074926487
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad83069000g200070_1.lc
Wrote FITS light curve to file ad83069000g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad83069000g200070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad83069000g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A222 Start Time (d) .... 9915 05:15:40.207
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9915 18:21:14.217
No. of Rows ....... 20 Bin Time (s) ...... 815.5
Right Ascension ... 2.4425E+01 Internal time sys.. Converted to TJD
Declination ....... -1.2914E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 58 Newbins of 815.481 (s)
Intv 1 Start 9915 5:22:27
Ser.1 Avg 0.6262E-01 Chisq 12.35 Var 0.5426E-04 Newbs. 20
Min 0.5059E-01 Max 0.7777E-01expVar 0.8787E-04 Bins 20
Results from Statistical Analysis
Newbin Integration Time (s).. 815.48
Interval Duration (s)........ 45667.
No. of Newbins .............. 20
Average (c/s) ............... 0.62621E-01 +/- 0.22E-02
Standard Deviation (c/s)..... 0.73665E-02
Minimum (c/s)................ 0.50589E-01
Maximum (c/s)................ 0.77769E-01
Variance ((c/s)**2).......... 0.54265E-04 +/- 0.18E-04
Expected Variance ((c/s)**2). 0.87866E-04 +/- 0.29E-04
Third Moment ((c/s)**3)...... 0.41001E-07
Average Deviation (c/s)...... 0.61665E-02
Skewness..................... 0.10257 +/- 0.55
Kurtosis.....................-0.86329 +/- 1.1
RMS fractional variation....< 0.19160 (3 sigma)
Chi-Square................... 12.352 dof 19
Chi-Square Prob of constancy. 0.87003 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.16182 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 58 Newbins of 815.481 (s)
Intv 1 Start 9915 5:22:27
Ser.1 Avg 0.6262E-01 Chisq 12.35 Var 0.5426E-04 Newbs. 20
Min 0.5059E-01 Max 0.7777E-01expVar 0.8787E-04 Bins 20
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad83069000g225670_2.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.85E+04 3162 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.85E+04 3162 1024
2 A222 PH HIGH 17/07/95 05:15:40 0.91E+04 3360 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.evt
Total Good Bad: Region Time Phase Cut
3162 550 2612 0 0 0
Writing events file
550 events written to the output file
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.evt
Total Good Bad: Region Time Phase Cut
3360 577 2783 0 0 0
Writing events file
1127 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6522 1127 5395 0 0 0
in 17598.07 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > read events ad83069000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > filter region ad83069000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad83069000g200070_2.lc with binsize 780.748649917298
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.18E+05 1127 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1127 1127 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1127 1127 0 0 0 0
in 17598.07 seconds
Fits light curve has 1127 counts for 6.4041E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > set binsize 780.748649917298
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad83069000g200070_2.lc
Wrote FITS light curve to file ad83069000g200070_2.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad83069000g200070_2_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad83069000g200070_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A222 Start Time (d) .... 9915 05:15:40.207
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9915 18:21:14.217
No. of Rows ....... 21 Bin Time (s) ...... 780.7
Right Ascension ... 2.4425E+01 Internal time sys.. Converted to TJD
Declination ....... -1.2914E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 61 Newbins of 780.749 (s)
Intv 1 Start 9915 5:22:10
Ser.1 Avg 0.6390E-01 Chisq 34.32 Var 0.1575E-03 Newbs. 21
Min 0.4572E-01 Max 0.9115E-01expVar 0.9639E-04 Bins 21
Results from Statistical Analysis
Newbin Integration Time (s).. 780.75
Interval Duration (s)........ 46064.
No. of Newbins .............. 21
Average (c/s) ............... 0.63901E-01 +/- 0.22E-02
Standard Deviation (c/s)..... 0.12550E-01
Minimum (c/s)................ 0.45717E-01
Maximum (c/s)................ 0.91150E-01
Variance ((c/s)**2).......... 0.15751E-03 +/- 0.50E-04
Expected Variance ((c/s)**2). 0.96388E-04 +/- 0.30E-04
Third Moment ((c/s)**3)...... 0.97275E-06
Average Deviation (c/s)...... 0.10601E-01
Skewness..................... 0.49210 +/- 0.53
Kurtosis.....................-0.69842 +/- 1.1
RMS fractional variation....< 0.11746 (3 sigma)
Chi-Square................... 34.316 dof 20
Chi-Square Prob of constancy. 0.24069E-01 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.11707 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 61 Newbins of 780.749 (s)
Intv 1 Start 9915 5:22:10
Ser.1 Avg 0.6390E-01 Chisq 34.32 Var 0.1575E-03 Newbs. 21
Min 0.4572E-01 Max 0.9115E-01expVar 0.9639E-04 Bins 21
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=5.0000000000E-01 for ad83069000g300170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.84E+04 3272 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.84E+04 3272 1024
2 A222 PH HIGH 17/07/95 05:15:42 0.91E+04 3580 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.evt
Total Good Bad: Region Time Phase Cut
3272 497 2775 0 0 0
Writing events file
497 events written to the output file
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.evt
Total Good Bad: Region Time Phase Cut
3580 558 3022 0 0 0
Writing events file
1055 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6852 1055 5797 0 0 0
in 17562.07 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > read events ad83069000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > filter region ad83069000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad83069000g300070_1.lc with binsize 832.325814751935
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.18E+05 1055 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1055 1055 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1055 1055 0 0 0 0
in 17562.07 seconds
Fits light curve has 1055 counts for 6.0073E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > set binsize 832.325814751935
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad83069000g300070_1.lc
Wrote FITS light curve to file ad83069000g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad83069000g300070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad83069000g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A222 Start Time (d) .... 9915 05:15:42.207
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9915 18:21:14.217
No. of Rows ....... 22 Bin Time (s) ...... 832.3
Right Ascension ... 2.4425E+01 Internal time sys.. Converted to TJD
Declination ....... -1.2914E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 57 Newbins of 832.326 (s)
Intv 1 Start 9915 5:22:38
Ser.1 Avg 0.5982E-01 Chisq 23.99 Var 0.9645E-04 Newbs. 22
Min 0.3663E-01 Max 0.7988E-01expVar 0.8846E-04 Bins 22
Results from Statistical Analysis
Newbin Integration Time (s).. 832.33
Interval Duration (s)........ 45778.
No. of Newbins .............. 22
Average (c/s) ............... 0.59818E-01 +/- 0.21E-02
Standard Deviation (c/s)..... 0.98209E-02
Minimum (c/s)................ 0.36626E-01
Maximum (c/s)................ 0.79878E-01
Variance ((c/s)**2).......... 0.96450E-04 +/- 0.30E-04
Expected Variance ((c/s)**2). 0.88456E-04 +/- 0.27E-04
Third Moment ((c/s)**3)......-0.16606E-06
Average Deviation (c/s)...... 0.75182E-02
Skewness.....................-0.17532 +/- 0.52
Kurtosis.....................-0.42230E-01 +/- 1.0
RMS fractional variation....< 0.16427 (3 sigma)
Chi-Square................... 23.988 dof 21
Chi-Square Prob of constancy. 0.29368 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.37582 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 57 Newbins of 832.326 (s)
Intv 1 Start 9915 5:22:38
Ser.1 Avg 0.5982E-01 Chisq 23.99 Var 0.9645E-04 Newbs. 22
Min 0.3663E-01 Max 0.7988E-01expVar 0.8846E-04 Bins 22
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Extracting events from region ad83069000g325670_2.reg
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.84E+04 3272 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.84E+04 3272 1024
2 A222 PH HIGH 17/07/95 05:15:42 0.91E+04 3580 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.evt
Total Good Bad: Region Time Phase Cut
3272 600 2672 0 0 0
Writing events file
600 events written to the output file
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.evt
Total Good Bad: Region Time Phase Cut
3580 692 2888 0 0 0
Writing events file
1292 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6852 1292 5560 0 0 0
in 17562.07 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > read events ad83069000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > filter region ad83069000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad83069000g300070_2.lc with binsize 679.64685337716
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.18E+05 1292 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/events.tmp
Total Good Bad: Region Time Phase Cut
1292 1292 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1292 1292 0 0 0 0
in 17562.07 seconds
Fits light curve has 1292 counts for 7.3568E-02 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > set binsize 679.64685337716
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad83069000g300070_2.lc
Wrote FITS light curve to file ad83069000g300070_2.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad83069000g300070_2_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad83069000g300070_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ A222 Start Time (d) .... 9915 05:15:42.207
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9915 18:21:14.217
No. of Rows ....... 25 Bin Time (s) ...... 679.6
Right Ascension ... 2.4425E+01 Internal time sys.. Converted to TJD
Declination ....... -1.2914E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 70 Newbins of 679.647 (s)
Intv 1 Start 9915 5:21:22
Ser.1 Avg 0.7204E-01 Chisq 22.06 Var 0.1103E-03 Newbs. 25
Min 0.5274E-01 Max 0.8975E-01expVar 0.1250E-03 Bins 25
Results from Statistical Analysis
Newbin Integration Time (s).. 679.65
Interval Duration (s)........ 46216.
No. of Newbins .............. 25
Average (c/s) ............... 0.72037E-01 +/- 0.23E-02
Standard Deviation (c/s)..... 0.10501E-01
Minimum (c/s)................ 0.52739E-01
Maximum (c/s)................ 0.89752E-01
Variance ((c/s)**2).......... 0.11027E-03 +/- 0.32E-04
Expected Variance ((c/s)**2). 0.12497E-03 +/- 0.36E-04
Third Moment ((c/s)**3)...... 0.38925E-07
Average Deviation (c/s)...... 0.84938E-02
Skewness..................... 0.33616E-01 +/- 0.49
Kurtosis.....................-0.85493 +/- 0.98
RMS fractional variation....< 0.17058 (3 sigma)
Chi-Square................... 22.060 dof 24
Chi-Square Prob of constancy. 0.57562 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.11677 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 70 Newbins of 679.647 (s)
Intv 1 Start 9915 5:21:22
Ser.1 Avg 0.7204E-01 Chisq 22.06 Var 0.1103E-03 Newbs. 25
Min 0.5274E-01 Max 0.8975E-01expVar 0.1250E-03 Bins 25
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad83069000g200170m.evt[2] ad83069000g200270h.evt[2]-> Making L1 light curve of ft950717_0421_1830G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 19148 output records from 19202 good input G2_L1 records.-> Making L1 light curve of ft950717_0421_1830G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 15942 output records from 26943 good input G2_L1 records.-> Merging GTIs from the following files:
ad83069000g300170m.evt[2] ad83069000g300270h.evt[2]-> Making L1 light curve of ft950717_0421_1830G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 18157 output records from 18210 good input G3_L1 records.-> Making L1 light curve of ft950717_0421_1830G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 15747 output records from 25889 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.85E+04 3162 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.evt
Total Good Bad: Region Time Phase Cut
3162 500 2662 0 0 0
Writing events file
500 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3162 500 2662 0 0 0
in 8479.90 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > filter region ad83069000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad83069000g200170m_1.ulc use_events=yes
Wrote events list to file ad83069000g200170m_1.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad83069000g200170m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.85E+04 3162 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.evt
Total Good Bad: Region Time Phase Cut
3162 550 2612 0 0 0
Writing events file
550 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3162 550 2612 0 0 0
in 8479.90 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > filter region ad83069000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad83069000g200170m_2.ulc use_events=yes
Wrote events list to file ad83069000g200170m_2.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad83069000g200270h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH HIGH 17/07/95 05:15:40 0.91E+04 3360 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.evt
Total Good Bad: Region Time Phase Cut
3360 579 2781 0 0 0
Writing events file
579 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3360 579 2781 0 0 0
in 9118.17 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > filter region ad83069000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad83069000g200270h_1.ulc use_events=yes
Wrote events list to file ad83069000g200270h_1.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad83069000g200270h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH HIGH 17/07/95 05:15:40 0.91E+04 3360 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.evt
Total Good Bad: Region Time Phase Cut
3360 577 2783 0 0 0
Writing events file
577 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3360 577 2783 0 0 0
in 9118.17 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > filter region ad83069000g225670_2.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad83069000g200270h_2.ulc use_events=yes
Wrote events list to file ad83069000g200270h_2.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad83069000g300170m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.84E+04 3272 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.evt
Total Good Bad: Region Time Phase Cut
3272 497 2775 0 0 0
Writing events file
497 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3272 497 2775 0 0 0
in 8447.90 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > filter region ad83069000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad83069000g300170m_1.ulc use_events=yes
Wrote events list to file ad83069000g300170m_1.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad83069000g300170m_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.84E+04 3272 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.evt
Total Good Bad: Region Time Phase Cut
3272 600 2672 0 0 0
Writing events file
600 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3272 600 2672 0 0 0
in 8447.90 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > filter region ad83069000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad83069000g300170m_2.ulc use_events=yes
Wrote events list to file ad83069000g300170m_2.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad83069000g300270h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH HIGH 17/07/95 05:15:42 0.91E+04 3580 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.evt
Total Good Bad: Region Time Phase Cut
3580 558 3022 0 0 0
Writing events file
558 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3580 558 3022 0 0 0
in 9114.17 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > filter region ad83069000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad83069000g300270h_1.ulc use_events=yes
Wrote events list to file ad83069000g300270h_1.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad83069000g300270h_2.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH HIGH 17/07/95 05:15:42 0.91E+04 3580 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.evt
Total Good Bad: Region Time Phase Cut
3580 692 2888 0 0 0
Writing events file
692 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3580 692 2888 0 0 0
in 9114.17 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > filter region ad83069000g325670_2.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad83069000g300270h_2.ulc use_events=yes
Wrote events list to file ad83069000g300270h_2.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad83069000s000102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.85E+04 1861 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000102h.evt
Total Good Bad: Region Time Phase Cut
1861 811 1050 0 0 0
Writing events file
811 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1861 811 1050 0 0 0
in 8473.05 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad83069000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad83069000s000102h_1.ulc use_events=yes
Wrote events list to file ad83069000s000102h_1.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad83069000s000112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT2 HIGH 17/07/95 05:12:18 0.85E+04 1941 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000112h.evt
Total Good Bad: Region Time Phase Cut
1941 827 1114 0 0 0
Writing events file
827 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1941 827 1114 0 0 0
in 8473.05 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad83069000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad83069000s000112h_1.ulc use_events=yes
Wrote events list to file ad83069000s000112h_1.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad83069000s000202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT MEDIUM 17/07/95 04:21:18 0.89E+04 2383 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000202m.evt
Total Good Bad: Region Time Phase Cut
2383 928 1455 0 0 0
Writing events file
928 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2383 928 1455 0 0 0
in 8884.53 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS0-BRIGHT > filter region ad83069000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad83069000s000202m_1.ulc use_events=yes
Wrote events list to file ad83069000s000202m_1.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad83069000s100102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.85E+04 1664 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100102h.evt
Total Good Bad: Region Time Phase Cut
1664 740 924 0 0 0
Writing events file
740 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1664 740 924 0 0 0
in 8500.50 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS1-BRIGHT > filter region ad83069000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad83069000s100102h_1.ulc use_events=yes
Wrote events list to file ad83069000s100102h_1.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad83069000s100112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT2 HIGH 17/07/95 05:12:18 0.85E+04 1744 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100112h.evt
Total Good Bad: Region Time Phase Cut
1744 752 992 0 0 0
Writing events file
752 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1744 752 992 0 0 0
in 8500.50 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad83069000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad83069000s100112h_1.ulc use_events=yes
Wrote events list to file ad83069000s100112h_1.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad83069000s100202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT MEDIUM 17/07/95 04:21:18 0.88E+04 2434 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100202m.evt
Total Good Bad: Region Time Phase Cut
2434 809 1625 0 0 0
Writing events file
809 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2434 809 1625 0 0 0
in 8774.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-SIS1-BRIGHT > filter region ad83069000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad83069000s100202m_1.ulc use_events=yes
Wrote events list to file ad83069000s100202m_1.ulc
Changing Data directory from:
/data/data18/seq_proc/83069000.004/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 7640 Total of 0 sets of frame data are extracted.
1 ad83069000g200170m.unf 37947 1 ad83069000g200270h.unf 37947 1 ad83069000g200370l.unf 37947-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.14E+05 15104 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.14E+05 15104 1024
2 A222 PH HIGH 17/07/95 05:15:40 0.11E+05 11447 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.14E+05 15104 1024
2 A222 PH HIGH 17/07/95 05:15:40 0.11E+05 11447 1024
3 A222 PH LOW 17/07/95 04:30:50 0.16E+05 11396 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.unf
Total Good Bad: Region Time Phase Cut
15104 3264 11840 0 0 0
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.unf
Total Good Bad: Region Time Phase Cut
11447 2685 8762 0 0 0
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200370l.unf
Total Good Bad: Region Time Phase Cut
11396 3600 7796 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
37947 9549 28398 0 0 0
in 41313.86 seconds
Spectrum has 9549 counts for 0.2311 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 41314. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad83069000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > read events ad83069000g200270h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > read events ad83069000g200370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad83069000g220170.cal group=yes
Wrote spectrum to ad83069000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 10:05:56 28-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad83069000g220170.cal
Net count rate (cts/s) for file 1 0.2311 +/- 2.3658E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.1159E+06 using 84 PHA bins.
Reduced chi-squared = 1.4492E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.1070E+06 using 84 PHA bins.
Reduced chi-squared = 1.4193E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.1070E+06 using 84 PHA bins.
Reduced chi-squared = 1.4013E+04
!XSPEC> renorm
Chi-Squared = 2850. using 84 PHA bins.
Reduced chi-squared = 36.08
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
2222.2 0 1.000 5.892 0.1035 7.0805E-02
6.1813E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
800.28 0 1.000 5.861 0.1550 0.1074
5.4381E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
283.18 -1 1.000 5.904 0.1670 0.1503
3.7253E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
236.49 -2 1.000 5.936 0.1855 0.1659
2.7044E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
235.79 -3 1.000 5.932 0.1819 0.1648
2.8138E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
235.79 -2 1.000 5.933 0.1821 0.1650
2.7938E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.93277 +/- 0.56598E-02
3 3 2 gaussian/b Sigma 0.182143 +/- 0.60361E-02
4 4 2 gaussian/b norm 0.165021 +/- 0.25464E-02
5 2 3 gaussian/b LineE 6.53201 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.191121 = par 3 * 1.0493
7 5 3 gaussian/b norm 2.793797E-02 +/- 0.17494E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 235.8 using 84 PHA bins.
Reduced chi-squared = 2.985
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad83069000g220170.cal peaks at 5.93277 +/- 0.0056598 keV1 ad83069000g300170m.unf 35623 1 ad83069000g300270h.unf 35623 1 ad83069000g300370l.unf 35623-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.14E+05 14255 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.14E+05 14255 1024
2 A222 PH HIGH 17/07/95 05:15:42 0.11E+05 10773 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.14E+05 14255 1024
2 A222 PH HIGH 17/07/95 05:15:42 0.11E+05 10773 1024
3 A222 PH LOW 17/07/95 04:30:50 0.16E+05 10595 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.unf
Total Good Bad: Region Time Phase Cut
14255 2915 11340 0 0 0
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.unf
Total Good Bad: Region Time Phase Cut
10773 2410 8363 0 0 0
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300370l.unf
Total Good Bad: Region Time Phase Cut
10595 3282 7313 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
35623 8607 27016 0 0 0
in 41275.86 seconds
Spectrum has 8607 counts for 0.2085 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 41276. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad83069000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!xsel:ASCA > read events ad83069000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > read events ad83069000g300270h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > read events ad83069000g300370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad83069000g320170.cal group=yes
Wrote spectrum to ad83069000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 10:07:59 28-Apr-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad83069000g320170.cal
Net count rate (cts/s) for file 1 0.2085 +/- 2.2487E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.2706E+06 using 84 PHA bins.
Reduced chi-squared = 1.6502E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.2607E+06 using 84 PHA bins.
Reduced chi-squared = 1.6163E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.2607E+06 using 84 PHA bins.
Reduced chi-squared = 1.5959E+04
!XSPEC> renorm
Chi-Squared = 2940. using 84 PHA bins.
Reduced chi-squared = 37.21
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
2322.0 0 1.000 5.893 0.1000 6.4172E-02
5.4932E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
903.41 0 1.000 5.868 0.1457 0.1016
4.7256E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
248.72 -1 1.000 5.931 0.1590 0.1473
2.8192E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
210.59 -2 1.000 5.950 0.1613 0.1601
2.1739E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
208.04 -3 1.000 5.943 0.1537 0.1584
2.3470E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
207.94 -4 1.000 5.945 0.1543 0.1589
2.3008E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
207.91 -5 1.000 5.944 0.1539 0.1588
2.3118E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
207.91 0 1.000 5.944 0.1539 0.1588
2.3112E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.94435 +/- 0.47594E-02
3 3 2 gaussian/b Sigma 0.153874 +/- 0.59987E-02
4 4 2 gaussian/b norm 0.158807 +/- 0.23118E-02
5 2 3 gaussian/b LineE 6.54476 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.161458 = par 3 * 1.0493
7 5 3 gaussian/b norm 2.311239E-02 +/- 0.13969E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 207.9 using 84 PHA bins.
Reduced chi-squared = 2.632
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad83069000g320170.cal peaks at 5.94435 +/- 0.0047594 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.12E+05 187090 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/83069000.004/ad83069000s000102h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad83069000s000102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT2 HIGH 17/07/95 05:12:18 0.12E+05 187559 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/83069000.004/ad83069000s000112h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad83069000s000112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT MEDIUM 17/07/95 04:21:18 0.15E+05 228575 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000202m.unf
Total Good Bad: Region Time Phase Cut
228575 4062 0 224513 0 0
Writing events file
4062 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
228575 4062 0 224513 0 0
in 310.05 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad83069000s000202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad83069000s000202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 4062
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 72 2671
Flickering pixels iter, pixels & cnts : 1 27 237
cleaning chip # 1
Hot pixels & counts : 36 1036
Flickering pixels iter, pixels & cnts : 1 8 48
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 143
Number of (internal) image counts : 4062
Number of image cts rejected (N, %) : 3992 98.2767105
By chip : 0 1 2 3
Pixels rejected : 99 44 0 0
Image counts : 2939 1123 0 0
Image cts rejected: 2908 1084 0 0
Image cts rej (%) : 98.95 96.53 0.00 0.00
filtering data...
Total counts : 2939 1123 0 0
Total cts rejected: 2908 1084 0 0
Total cts rej (%) : 98.95 96.53 0.00 0.00
Number of clean counts accepted : 70
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 143
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad83069000s000302l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 A222 BRIGHT LOW 17/07/95 04:30:38 0.17E+05 68617 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s000302l.unf
Total Good Bad: Region Time Phase Cut
68617 63153 0 5464 0 0
Writing events file
63153 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
68617 63153 0 5464 0 0
in 8243.55 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000s000302l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad83069000s000302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad83069000s000302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 63153
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 44 31301
Flickering pixels iter, pixels & cnts : 1 28 692
cleaning chip # 1
Hot pixels & counts : 44 29763
Flickering pixels iter, pixels & cnts : 1 24 741
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 140
Number of (internal) image counts : 63153
Number of image cts rejected (N, %) : 62497 98.9612503
By chip : 0 1 2 3
Pixels rejected : 72 68 0 0
Image counts : 32256 30897 0 0
Image cts rejected: 31993 30504 0 0
Image cts rej (%) : 99.18 98.73 0.00 0.00
filtering data...
Total counts : 32256 30897 0 0
Total cts rejected: 31993 30504 0 0
Total cts rej (%) : 99.18 98.73 0.00 0.00
Number of clean counts accepted : 656
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 140
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad83069000s100102h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT HIGH 17/07/95 05:12:18 0.12E+05 209110 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/83069000.004/ad83069000s100102h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad83069000s100102h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT2 HIGH 17/07/95 05:12:18 0.12E+05 209560 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/83069000.004/ad83069000s100112h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad83069000s100112h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT MEDIUM 17/07/95 04:21:18 0.15E+05 267992 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100202m.unf
Total Good Bad: Region Time Phase Cut
267992 4362 0 263630 0 0
Writing events file
4362 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
267992 4362 0 263630 0 0
in 310.05 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad83069000s100202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad83069000s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 4362
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 53 1829
Flickering pixels iter, pixels & cnts : 1 27 201
cleaning chip # 3
Hot pixels & counts : 60 2075
Flickering pixels iter, pixels & cnts : 1 21 142
Number of pixels rejected : 161
Number of (internal) image counts : 4362
Number of image cts rejected (N, %) : 4247 97.3635941
By chip : 0 1 2 3
Pixels rejected : 0 0 80 81
Image counts : 0 0 2087 2275
Image cts rejected: 0 0 2030 2217
Image cts rej (%) : 0.00 0.00 97.27 97.45
filtering data...
Total counts : 0 0 2087 2275
Total cts rejected: 0 0 2030 2217
Total cts rej (%) : 0.00 0.00 97.27 97.45
Number of clean counts accepted : 115
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 161
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad83069000s100302l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 A222 BRIGHT LOW 17/07/95 04:30:38 0.17E+05 77669 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000s100302l.unf
Total Good Bad: Region Time Phase Cut
77669 64512 0 13157 0 0
Writing events file
64512 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
77669 64512 0 13157 0 0
in 8243.55 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad83069000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad83069000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 64512
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 46 31304
Flickering pixels iter, pixels & cnts : 1 29 697
cleaning chip # 3
Hot pixels & counts : 42 30082
Flickering pixels iter, pixels & cnts : 1 63 1934
Number of pixels rejected : 180
Number of (internal) image counts : 64512
Number of image cts rejected (N, %) : 64017 99.2327042
By chip : 0 1 2 3
Pixels rejected : 0 0 75 105
Image counts : 0 0 32256 32256
Image cts rejected: 0 0 32001 32016
Image cts rej (%) : 0.00 0.00 99.21 99.26
filtering data...
Total counts : 0 0 32256 32256
Total cts rejected: 0 0 32001 32016
Total cts rej (%) : 0.00 0.00 99.21 99.26
Number of clean counts accepted : 495
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 180
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad83069000g200170m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.14E+05 15104 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.unf
Total Good Bad: Region Time Phase Cut
15104 165 0 14939 0 0
Writing events file
165 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15104 165 0 14939 0 0
in 288.04 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad83069000g200170m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.14E+05 15104 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200170m.unf
Total Good Bad: Region Time Phase Cut
15104 472 0 14632 0 0
Writing events file
472 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15104 472 0 14632 0 0
in 463.81 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad83069000g200270h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH HIGH 17/07/95 05:15:40 0.11E+05 11447 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad83069000g200270h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH HIGH 17/07/95 05:15:40 0.11E+05 11447 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200270h.unf
Total Good Bad: Region Time Phase Cut
11447 97 0 11350 0 0
Writing events file
97 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11447 97 0 11350 0 0
in 121.96 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad83069000g200370l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH LOW 17/07/95 04:30:50 0.16E+05 11396 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200370l.unf
Total Good Bad: Region Time Phase Cut
11396 5189 0 6207 0 0
Writing events file
5189 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11396 5189 0 6207 0 0
in 8095.70 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad83069000g200370l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH LOW 17/07/95 04:30:50 0.16E+05 11396 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g200370l.unf
Total Good Bad: Region Time Phase Cut
11396 5671 0 5725 0 0
Writing events file
5671 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11396 5671 0 5725 0 0
in 7456.35 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad83069000g300170m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.14E+05 14255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.unf
Total Good Bad: Region Time Phase Cut
14255 146 0 14109 0 0
Writing events file
146 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14255 146 0 14109 0 0
in 288.04 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad83069000g300170m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH MEDIUM 17/07/95 04:21:30 0.14E+05 14255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300170m.unf
Total Good Bad: Region Time Phase Cut
14255 406 0 13849 0 0
Writing events file
406 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14255 406 0 13849 0 0
in 463.81 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad83069000g300270h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH HIGH 17/07/95 05:15:42 0.11E+05 10773 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad83069000g300270h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH HIGH 17/07/95 05:15:42 0.11E+05 10773 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300270h.unf
Total Good Bad: Region Time Phase Cut
10773 89 0 10684 0 0
Writing events file
89 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10773 89 0 10684 0 0
in 123.96 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad83069000g300370l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH LOW 17/07/95 04:30:50 0.16E+05 10595 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300370l.unf
Total Good Bad: Region Time Phase Cut
10595 4714 0 5881 0 0
Writing events file
4714 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10595 4714 0 5881 0 0
in 8095.70 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad83069000g300370l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 A222 PH LOW 17/07/95 04:30:50 0.16E+05 10595 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data18/seq_proc/83069000.004/ad83069000g300370l.unf
Total Good Bad: Region Time Phase Cut
10595 5349 0 5246 0 0
Writing events file
5349 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10595 5349 0 5246 0 0
in 7456.35 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data18/seq_proc/83069000.004/
Setting mkf directory to /data/data18/seq_proc/83069000.004/
!earthevents:ASCA > read events ad83069000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data18/seq_proc/83069000.004/
HK Directory is: /data/data18/seq_proc/83069000.004/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files