The following information is also available:
Time column is TIME ORDERED-> Fetching fa960727_0447.1900.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 112596436.897300 112647648.719500
Data file start and stop ascatime : 112596436.897300 112647648.719500
Aspecting run start and stop ascatime : 112596436.897413 112647648.719417
Time interval averaged over (seconds) : 51211.822003
Total pointing and manuver time (sec) : 32542.480469 18669.482422
Mean boresight Euler angles : 203.624045 121.678946 156.897928
RA DEC SUN ANGLE
Mean solar position (deg) : 126.08 19.31
Mean aberration (arcsec) : -3.23 -6.54
Mean sat X-axis (deg) : 242.710499 51.513963 90.25
Mean sat Y-axis (deg) : 126.251061 19.506197 0.25
Mean sat Z-axis (deg) : 203.624045 -31.678947 90.03
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 203.291061 -31.701641 66.722450 0.429579
Minimum 203.018570 -31.775501 66.435936 0.000000
Maximum 203.387589 -31.537863 66.855232 17.041006
Sigma (RMS) 0.002550 0.001883 0.021517 1.047737
Number of ASPECT records processed = 51496
Aspecting to RA/DEC : 203.29106140 -31.70164108
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 203.291 DEC: -31.702
START TIME: SC 112596436.8974 = UT 27/07/96 04:47:16
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
0.500131 5.953 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
1291.995361 6.241 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1342.495239 5.237 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1383.995239 4.226 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1430.494873 3.222 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1491.494751 2.218 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1589.494385 1.214 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1871.493408 0.213 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2875.989746 0.274 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
6539.977051 0.695 8C03 1 1 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0
8635.969727 0.226 E08283 1 1 0 0 0 0 0 1 0 1 0 0 0 0 0 0 4
12279.957031 0.465 8C03 1 1 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0
14331.950195 0.180 E08283 1 1 0 0 0 0 0 1 0 1 0 0 0 0 0 0 4
18023.937500 0.267 8C03 1 1 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0
20075.929688 0.182 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
23769.917969 0.200 8C03 1 1 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0
25835.910156 0.187 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
29513.896484 0.246 8C03 1 1 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0
31579.890625 0.173 E08283 1 1 0 0 0 0 0 1 0 1 0 0 0 0 0 0 4
35257.878906 0.200 8C03 1 1 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0
37323.871094 0.137 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
41003.855469 0.191 8C03 1 1 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0
43067.851562 0.181 E08283 1 1 0 0 0 0 0 1 0 1 0 0 0 0 0 0 4
46747.835938 0.181 1C8C43 1 1 0 0 0 0 1 0 0 0 1 1 0 0 0 4 3
48811.832031 0.125 8203 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
51195.820312 0.290 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
51211.820312 17.041 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
Attitude Records: 51496
Attitude Steps: 27
Maneuver ACM time: 18669.5 sec
Pointed ACM time: 32542.5 sec
-> Calculating aspect point63 78 count=1 sum1=203.351 sum2=121.517 sum3=156.61 89 93 count=8182 sum1=1.666e+06 sum2=995528 sum3=1.28366e+06 89 94 count=88 sum1=17918.5 sum2=10707.5 sum3=13806.5 90 93 count=363 sum1=73914.1 sum2=44168 sum3=56952.3 90 94 count=40610 sum1=8.26906e+06 sum2=4.94131e+06 sum3=6.37148e+06 91 94 count=81 sum1=16494.1 sum2=9856.38 sum3=12709.1 91 95 count=242 sum1=49279.9 sum2=29448.3 sum3=37971.8 92 95 count=105 sum1=21382.6 sum2=12777.8 sum3=16476.4 92 96 count=38 sum1=7738.62 sum2=4624.47 sum3=5963.1 93 96 count=111 sum1=22605.6 sum2=13508.8 sum3=17419.4 93 97 count=9 sum1=1832.94 sum2=1095.35 sum3=1412.46 94 97 count=81 sum1=16496.9 sum2=9858.5 sum3=12712.6 95 97 count=4 sum1=814.684 sum2=486.856 sum3=627.816 95 98 count=56 sum1=11405.8 sum2=6816.19 sum3=8789.74 96 98 count=36 sum1=7332.57 sum2=4382.03 sum3=5650.9 96 99 count=29 sum1=5906.96 sum2=3530.1 sum3=4552.35 97 99 count=38 sum1=7740.36 sum2=4625.81 sum3=5965.46 97 100 count=18 sum1=3666.58 sum2=2191.25 sum3=2825.88 98 100 count=56 sum1=11407.5 sum2=6817.45 sum3=8792.13 99 100 count=19 sum1=3870.62 sum2=2313.14 sum3=2983.23 99 101 count=168 sum1=34224.5 sum2=20453.6 sum3=26379.3 100 100 count=211 sum1=42984.9 sum2=25687.2 sum3=33128.6 100 101 count=949 sum1=193330 sum2=115541 sum3=149016 0 out of 51495 points outside bin structure-> Euler angles: 203.621, 121.676, 156.893
Interpolating 30 records in time interval 1.12648e+08 - 1.12648e+08
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft960727_0447.1900",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft960727_0447.1900 Initial mode = 1 (Faint) Initial value for dummy = 0 Initial datamode = 2 (ACS) Initial sis = 1 Initial bit_rate = 4 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 760384 Bright = 0 Fast = 0 Frame = 64384 Dark frame = 0 Histogram = 0 Integration = 0 PH = 823744 MPC = 0 PCAL = 0 Memory Check = 1024 Number of superframes = 12954 no. of SIS events found = 866409-> Standard Error Output From FTOOL frfread
coordinate error 0 35 coordinate error 429 209 coordinate error 0 1 coordinate error 0 0-> Removing the following files with NEVENTS=0
ft960727_0447_1900G200199.fits ft960727_0447_1900G200470H.fits ft960727_0447_1900G200570L.fits ft960727_0447_1900G200670H.fits ft960727_0447_1900G200770H.fits ft960727_0447_1900G201399.fits ft960727_0447_1900G201570M.fits ft960727_0447_1900G201670L.fits ft960727_0447_1900G201770L.fits ft960727_0447_1900G201870M.fits ft960727_0447_1900G202299.fits ft960727_0447_1900G202470H.fits ft960727_0447_1900G202570H.fits ft960727_0447_1900G202670M.fits ft960727_0447_1900G202770H.fits ft960727_0447_1900G203299.fits ft960727_0447_1900G203470H.fits ft960727_0447_1900G203570H.fits ft960727_0447_1900G203670M.fits ft960727_0447_1900G203770H.fits ft960727_0447_1900G204070H.fits ft960727_0447_1900G204270H.fits ft960727_0447_1900G204370H.fits ft960727_0447_1900G204470H.fits ft960727_0447_1900G204570H.fits ft960727_0447_1900G205073H.fits ft960727_0447_1900G205470M.fits ft960727_0447_1900G205570L.fits ft960727_0447_1900G205670M.fits ft960727_0447_1900G205770M.fits ft960727_0447_1900G205870M.fits ft960727_0447_1900G205970M.fits ft960727_0447_1900G206670L.fits ft960727_0447_1900G206770M.fits ft960727_0447_1900G206870M.fits ft960727_0447_1900G206970M.fits ft960727_0447_1900G207070M.fits ft960727_0447_1900G207499.fits ft960727_0447_1900G207770H.fits ft960727_0447_1900G207870H.fits ft960727_0447_1900G207970H.fits ft960727_0447_1900G208070H.fits ft960727_0447_1900G208770M.fits ft960727_0447_1900G208870L.fits ft960727_0447_1900G208970L.fits ft960727_0447_1900G209070H.fits ft960727_0447_1900G209170H.fits ft960727_0447_1900G209970H.fits ft960727_0447_1900G210599.fits ft960727_0447_1900G300199.fits ft960727_0447_1900G300470H.fits ft960727_0447_1900G300570L.fits ft960727_0447_1900G300670H.fits ft960727_0447_1900G301399.fits ft960727_0447_1900G301570M.fits ft960727_0447_1900G301670L.fits ft960727_0447_1900G301770L.fits ft960727_0447_1900G301870M.fits ft960727_0447_1900G302299.fits ft960727_0447_1900G302470H.fits ft960727_0447_1900G302570H.fits ft960727_0447_1900G302670M.fits ft960727_0447_1900G302770H.fits ft960727_0447_1900G302870H.fits ft960727_0447_1900G303299.fits ft960727_0447_1900G303470H.fits ft960727_0447_1900G303570H.fits ft960727_0447_1900G303670M.fits ft960727_0447_1900G303770H.fits ft960727_0447_1900G304470H.fits ft960727_0447_1900G304570H.fits ft960727_0447_1900G304670H.fits ft960727_0447_1900G304873H.fits ft960727_0447_1900G305170M.fits ft960727_0447_1900G305270M.fits ft960727_0447_1900G305370L.fits ft960727_0447_1900G305470M.fits ft960727_0447_1900G305570M.fits ft960727_0447_1900G305670M.fits ft960727_0447_1900G305770M.fits ft960727_0447_1900G306470L.fits ft960727_0447_1900G306570M.fits ft960727_0447_1900G306670M.fits ft960727_0447_1900G306770M.fits ft960727_0447_1900G306870M.fits ft960727_0447_1900G307299.fits ft960727_0447_1900G307470H.fits ft960727_0447_1900G307670H.fits ft960727_0447_1900G307770H.fits ft960727_0447_1900G307870H.fits ft960727_0447_1900G307970H.fits ft960727_0447_1900G308370M.fits ft960727_0447_1900G308470L.fits ft960727_0447_1900G308570L.fits ft960727_0447_1900G308670H.fits ft960727_0447_1900G308870H.fits ft960727_0447_1900G309370H.fits ft960727_0447_1900G310199.fits ft960727_0447_1900S000199.fits ft960727_0447_1900S000704H.fits ft960727_0447_1900S001499.fits ft960727_0447_1900S001701L.fits ft960727_0447_1900S002199.fits ft960727_0447_1900S002301H.fits ft960727_0447_1900S003099.fits ft960727_0447_1900S003204H.fits ft960727_0447_1900S003601M.fits ft960727_0447_1900S003999.fits ft960727_0447_1900S005599.fits ft960727_0447_1900S006001L.fits ft960727_0447_1900S006101H.fits ft960727_0447_1900S006501H.fits ft960727_0447_1900S006999.fits ft960727_0447_1900S100199.fits ft960727_0447_1900S101399.fits ft960727_0447_1900S101601L.fits ft960727_0447_1900S102099.fits ft960727_0447_1900S102204H.fits ft960727_0447_1900S102999.fits ft960727_0447_1900S103401M.fits ft960727_0447_1900S103799.fits ft960727_0447_1900S105399.fits ft960727_0447_1900S105701L.fits ft960727_0447_1900S105801H.fits ft960727_0447_1900S106201H.fits ft960727_0447_1900S106699.fits-> Checking for empty GTI extensions
ft960727_0447_1900S000201H.fits[3] ft960727_0447_1900S000301H.fits[3] ft960727_0447_1900S000401H.fits[3] ft960727_0447_1900S000501H.fits[3] ft960727_0447_1900S000601H.fits[3] ft960727_0447_1900S000801H.fits[3] ft960727_0447_1900S000901L.fits[3] ft960727_0447_1900S001001L.fits[3] ft960727_0447_1900S001101L.fits[3] ft960727_0447_1900S001201H.fits[3] ft960727_0447_1900S001301M.fits[3] ft960727_0447_1900S001501M.fits[3] ft960727_0447_1900S001601L.fits[3] ft960727_0447_1900S001801L.fits[3] ft960727_0447_1900S001901M.fits[3] ft960727_0447_1900S002001H.fits[3] ft960727_0447_1900S002201H.fits[3] ft960727_0447_1900S002401H.fits[3] ft960727_0447_1900S002501H.fits[3] ft960727_0447_1900S002601M.fits[3] ft960727_0447_1900S002701M.fits[3] ft960727_0447_1900S002801M.fits[3] ft960727_0447_1900S002901H.fits[3] ft960727_0447_1900S003101H.fits[3] ft960727_0447_1900S003301H.fits[3] ft960727_0447_1900S003401H.fits[3] ft960727_0447_1900S003501M.fits[3] ft960727_0447_1900S003701M.fits[3] ft960727_0447_1900S003801H.fits[3] ft960727_0447_1900S004001H.fits[3] ft960727_0447_1900S004101H.fits[3] ft960727_0447_1900S004201M.fits[3] ft960727_0447_1900S004301L.fits[3] ft960727_0447_1900S004401L.fits[3] ft960727_0447_1900S004501L.fits[3] ft960727_0447_1900S004601M.fits[3] ft960727_0447_1900S004701H.fits[3] ft960727_0447_1900S004801H.fits[3] ft960727_0447_1900S004901M.fits[3] ft960727_0447_1900S005001L.fits[3] ft960727_0447_1900S005101L.fits[3] ft960727_0447_1900S005201L.fits[3] ft960727_0447_1900S005301M.fits[3] ft960727_0447_1900S005401H.fits[3] ft960727_0447_1900S005601H.fits[3] ft960727_0447_1900S005701H.fits[3] ft960727_0447_1900S005801M.fits[3] ft960727_0447_1900S005901L.fits[3] ft960727_0447_1900S006201H.fits[3] ft960727_0447_1900S006301M.fits[3] ft960727_0447_1900S006401H.fits[3] ft960727_0447_1900S006601H.fits[3] ft960727_0447_1900S006701M.fits[3] ft960727_0447_1900S006801H.fits[3]-> Merging GTIs from the following files:
ft960727_0447_1900S100201H.fits[3] ft960727_0447_1900S100301H.fits[3] ft960727_0447_1900S100401H.fits[3] ft960727_0447_1900S100501H.fits[3] ft960727_0447_1900S100601H.fits[3] ft960727_0447_1900S100701H.fits[3] ft960727_0447_1900S100801L.fits[3] ft960727_0447_1900S100901L.fits[3] ft960727_0447_1900S101001L.fits[3] ft960727_0447_1900S101101H.fits[3] ft960727_0447_1900S101201M.fits[3] ft960727_0447_1900S101401M.fits[3] ft960727_0447_1900S101501L.fits[3] ft960727_0447_1900S101701L.fits[3] ft960727_0447_1900S101801M.fits[3] ft960727_0447_1900S101901H.fits[3] ft960727_0447_1900S102101H.fits[3] ft960727_0447_1900S102301H.fits[3] ft960727_0447_1900S102401H.fits[3] ft960727_0447_1900S102501M.fits[3] ft960727_0447_1900S102601M.fits[3] ft960727_0447_1900S102701M.fits[3] ft960727_0447_1900S102801H.fits[3] ft960727_0447_1900S103001H.fits[3] ft960727_0447_1900S103101H.fits[3] ft960727_0447_1900S103201H.fits[3] ft960727_0447_1900S103301M.fits[3] ft960727_0447_1900S103501M.fits[3] ft960727_0447_1900S103601H.fits[3] ft960727_0447_1900S103801H.fits[3] ft960727_0447_1900S103901H.fits[3] ft960727_0447_1900S104001M.fits[3] ft960727_0447_1900S104101L.fits[3] ft960727_0447_1900S104201L.fits[3] ft960727_0447_1900S104301L.fits[3] ft960727_0447_1900S104401M.fits[3] ft960727_0447_1900S104501H.fits[3] ft960727_0447_1900S104601H.fits[3] ft960727_0447_1900S104701M.fits[3] ft960727_0447_1900S104801L.fits[3] ft960727_0447_1900S104901L.fits[3] ft960727_0447_1900S105001L.fits[3] ft960727_0447_1900S105101M.fits[3] ft960727_0447_1900S105201H.fits[3] ft960727_0447_1900S105401H.fits[3] ft960727_0447_1900S105501M.fits[3] ft960727_0447_1900S105601L.fits[3] ft960727_0447_1900S105901H.fits[3] ft960727_0447_1900S106001M.fits[3] ft960727_0447_1900S106101H.fits[3] ft960727_0447_1900S106301H.fits[3] ft960727_0447_1900S106401M.fits[3] ft960727_0447_1900S106501H.fits[3]-> Merging GTIs from the following files:
ft960727_0447_1900G200270H.fits[3] ft960727_0447_1900G200370H.fits[3] ft960727_0447_1900G200870H.fits[3] ft960727_0447_1900G200970H.fits[3] ft960727_0447_1900G201070H.fits[3] ft960727_0447_1900G201170M.fits[3] ft960727_0447_1900G201270M.fits[3] ft960727_0447_1900G201470M.fits[3] ft960727_0447_1900G201970M.fits[3] ft960727_0447_1900G202070M.fits[3] ft960727_0447_1900G202170H.fits[3] ft960727_0447_1900G202370H.fits[3] ft960727_0447_1900G202870H.fits[3] ft960727_0447_1900G202970H.fits[3] ft960727_0447_1900G203070H.fits[3] ft960727_0447_1900G203170H.fits[3] ft960727_0447_1900G203370H.fits[3] ft960727_0447_1900G203870H.fits[3] ft960727_0447_1900G203970H.fits[3] ft960727_0447_1900G204170H.fits[3] ft960727_0447_1900G204670H.fits[3] ft960727_0447_1900G204770H.fits[3] ft960727_0447_1900G204870H.fits[3] ft960727_0447_1900G204970H.fits[3] ft960727_0447_1900G205170H.fits[3] ft960727_0447_1900G205270M.fits[3] ft960727_0447_1900G205370M.fits[3] ft960727_0447_1900G206070M.fits[3] ft960727_0447_1900G206170M.fits[3] ft960727_0447_1900G206270H.fits[3] ft960727_0447_1900G206370M.fits[3] ft960727_0447_1900G206470L.fits[3] ft960727_0447_1900G206570L.fits[3] ft960727_0447_1900G207170M.fits[3] ft960727_0447_1900G207270M.fits[3] ft960727_0447_1900G207370H.fits[3] ft960727_0447_1900G207570H.fits[3] ft960727_0447_1900G207670H.fits[3] ft960727_0447_1900G208170H.fits[3] ft960727_0447_1900G208270H.fits[3] ft960727_0447_1900G208370H.fits[3] ft960727_0447_1900G208470H.fits[3] ft960727_0447_1900G208570H.fits[3] ft960727_0447_1900G208670M.fits[3] ft960727_0447_1900G209270H.fits[3] ft960727_0447_1900G209370H.fits[3] ft960727_0447_1900G209470H.fits[3] ft960727_0447_1900G209570M.fits[3] ft960727_0447_1900G209670H.fits[3] ft960727_0447_1900G209770H.fits[3] ft960727_0447_1900G209870H.fits[3] ft960727_0447_1900G210070H.fits[3] ft960727_0447_1900G210170H.fits[3] ft960727_0447_1900G210270H.fits[3] ft960727_0447_1900G210370M.fits[3] ft960727_0447_1900G210470H.fits[3]-> Merging GTIs from the following files:
ft960727_0447_1900G300270H.fits[3] ft960727_0447_1900G300370H.fits[3] ft960727_0447_1900G300770H.fits[3] ft960727_0447_1900G300870H.fits[3] ft960727_0447_1900G300970H.fits[3] ft960727_0447_1900G301070H.fits[3] ft960727_0447_1900G301170M.fits[3] ft960727_0447_1900G301270M.fits[3] ft960727_0447_1900G301470M.fits[3] ft960727_0447_1900G301970M.fits[3] ft960727_0447_1900G302070M.fits[3] ft960727_0447_1900G302170H.fits[3] ft960727_0447_1900G302370H.fits[3] ft960727_0447_1900G302970H.fits[3] ft960727_0447_1900G303070H.fits[3] ft960727_0447_1900G303170H.fits[3] ft960727_0447_1900G303370H.fits[3] ft960727_0447_1900G303870H.fits[3] ft960727_0447_1900G303970H.fits[3] ft960727_0447_1900G304070H.fits[3] ft960727_0447_1900G304170H.fits[3] ft960727_0447_1900G304270H.fits[3] ft960727_0447_1900G304370H.fits[3] ft960727_0447_1900G304770H.fits[3] ft960727_0447_1900G304970H.fits[3] ft960727_0447_1900G305070M.fits[3] ft960727_0447_1900G305870M.fits[3] ft960727_0447_1900G305970M.fits[3] ft960727_0447_1900G306070H.fits[3] ft960727_0447_1900G306170M.fits[3] ft960727_0447_1900G306270L.fits[3] ft960727_0447_1900G306370L.fits[3] ft960727_0447_1900G306970M.fits[3] ft960727_0447_1900G307070M.fits[3] ft960727_0447_1900G307170H.fits[3] ft960727_0447_1900G307370H.fits[3] ft960727_0447_1900G307570H.fits[3] ft960727_0447_1900G308070H.fits[3] ft960727_0447_1900G308170H.fits[3] ft960727_0447_1900G308270M.fits[3] ft960727_0447_1900G308770H.fits[3] ft960727_0447_1900G308970H.fits[3] ft960727_0447_1900G309070H.fits[3] ft960727_0447_1900G309170M.fits[3] ft960727_0447_1900G309270H.fits[3] ft960727_0447_1900G309470H.fits[3] ft960727_0447_1900G309570H.fits[3] ft960727_0447_1900G309670H.fits[3] ft960727_0447_1900G309770H.fits[3] ft960727_0447_1900G309870H.fits[3] ft960727_0447_1900G309970M.fits[3] ft960727_0447_1900G310070H.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200370h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g200470h.prelist merge count = 2 photon cnt = 3 GISSORTSPLIT:LO:g200570h.prelist merge count = 2 photon cnt = 3 GISSORTSPLIT:LO:g200670h.prelist merge count = 5 photon cnt = 11 GISSORTSPLIT:LO:g200770h.prelist merge count = 4 photon cnt = 9 GISSORTSPLIT:LO:g200870h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200970h.prelist merge count = 16 photon cnt = 26903 GISSORTSPLIT:LO:g201070h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g201170h.prelist merge count = 2 photon cnt = 27 GISSORTSPLIT:LO:g201270h.prelist merge count = 2 photon cnt = 3 GISSORTSPLIT:LO:g201370h.prelist merge count = 1 photon cnt = 912 GISSORTSPLIT:LO:g200170l.prelist merge count = 1 photon cnt = 15 GISSORTSPLIT:LO:g200270l.prelist merge count = 1 photon cnt = 55 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200270m.prelist merge count = 2 photon cnt = 25 GISSORTSPLIT:LO:g200370m.prelist merge count = 1 photon cnt = 18 GISSORTSPLIT:LO:g200470m.prelist merge count = 10 photon cnt = 12274 GISSORTSPLIT:LO:g200570m.prelist merge count = 1 photon cnt = 52 GISSORTSPLIT:LO:Total filenames split = 56 GISSORTSPLIT:LO:Total split file cnt = 20 GISSORTSPLIT:LO:End program-> Creating ad84041000g200170h.unf
---- cmerge: version 1.5 ---- A total of 16 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900G200270H.fits 2 -- ft960727_0447_1900G201070H.fits 3 -- ft960727_0447_1900G202170H.fits 4 -- ft960727_0447_1900G202370H.fits 5 -- ft960727_0447_1900G203170H.fits 6 -- ft960727_0447_1900G203370H.fits 7 -- ft960727_0447_1900G204170H.fits 8 -- ft960727_0447_1900G204970H.fits 9 -- ft960727_0447_1900G206270H.fits 10 -- ft960727_0447_1900G207370H.fits 11 -- ft960727_0447_1900G207570H.fits 12 -- ft960727_0447_1900G208570H.fits 13 -- ft960727_0447_1900G209470H.fits 14 -- ft960727_0447_1900G209670H.fits 15 -- ft960727_0447_1900G210270H.fits 16 -- ft960727_0447_1900G210470H.fits Merging binary extension #: 2 1 -- ft960727_0447_1900G200270H.fits 2 -- ft960727_0447_1900G201070H.fits 3 -- ft960727_0447_1900G202170H.fits 4 -- ft960727_0447_1900G202370H.fits 5 -- ft960727_0447_1900G203170H.fits 6 -- ft960727_0447_1900G203370H.fits 7 -- ft960727_0447_1900G204170H.fits 8 -- ft960727_0447_1900G204970H.fits 9 -- ft960727_0447_1900G206270H.fits 10 -- ft960727_0447_1900G207370H.fits 11 -- ft960727_0447_1900G207570H.fits 12 -- ft960727_0447_1900G208570H.fits 13 -- ft960727_0447_1900G209470H.fits 14 -- ft960727_0447_1900G209670H.fits 15 -- ft960727_0447_1900G210270H.fits 16 -- ft960727_0447_1900G210470H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000g200270m.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900G201270M.fits 2 -- ft960727_0447_1900G201470M.fits 3 -- ft960727_0447_1900G202070M.fits 4 -- ft960727_0447_1900G205270M.fits 5 -- ft960727_0447_1900G206170M.fits 6 -- ft960727_0447_1900G206370M.fits 7 -- ft960727_0447_1900G207270M.fits 8 -- ft960727_0447_1900G208670M.fits 9 -- ft960727_0447_1900G209570M.fits 10 -- ft960727_0447_1900G210370M.fits Merging binary extension #: 2 1 -- ft960727_0447_1900G201270M.fits 2 -- ft960727_0447_1900G201470M.fits 3 -- ft960727_0447_1900G202070M.fits 4 -- ft960727_0447_1900G205270M.fits 5 -- ft960727_0447_1900G206170M.fits 6 -- ft960727_0447_1900G206370M.fits 7 -- ft960727_0447_1900G207270M.fits 8 -- ft960727_0447_1900G208670M.fits 9 -- ft960727_0447_1900G209570M.fits 10 -- ft960727_0447_1900G210370M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft960727_0447_1900G205170H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900G205170H.fits Merging binary extension #: 2 1 -- ft960727_0447_1900G205170H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000055 events
ft960727_0447_1900G206470L.fits-> Ignoring the following files containing 000000052 events
ft960727_0447_1900G201170M.fits-> Ignoring the following files containing 000000027 events
ft960727_0447_1900G204770H.fits ft960727_0447_1900G208370H.fits-> Ignoring the following files containing 000000025 events
ft960727_0447_1900G206070M.fits ft960727_0447_1900G207170M.fits-> Ignoring the following files containing 000000018 events
ft960727_0447_1900G201970M.fits-> Ignoring the following files containing 000000015 events
ft960727_0447_1900G206570L.fits-> Ignoring the following files containing 000000011 events
ft960727_0447_1900G200870H.fits ft960727_0447_1900G202970H.fits ft960727_0447_1900G203970H.fits ft960727_0447_1900G209270H.fits ft960727_0447_1900G210070H.fits-> Ignoring the following files containing 000000009 events
ft960727_0447_1900G200970H.fits ft960727_0447_1900G203070H.fits ft960727_0447_1900G209370H.fits ft960727_0447_1900G210170H.fits-> Ignoring the following files containing 000000004 events
ft960727_0447_1900G209870H.fits-> Ignoring the following files containing 000000003 events
ft960727_0447_1900G204870H.fits ft960727_0447_1900G208470H.fits-> Ignoring the following files containing 000000003 events
ft960727_0447_1900G202870H.fits ft960727_0447_1900G203870H.fits-> Ignoring the following files containing 000000003 events
ft960727_0447_1900G200370H.fits ft960727_0447_1900G209770H.fits-> Ignoring the following files containing 000000003 events
ft960727_0447_1900G208170H.fits-> Ignoring the following files containing 000000002 events
ft960727_0447_1900G207670H.fits-> Ignoring the following files containing 000000002 events
ft960727_0447_1900G205370M.fits-> Ignoring the following files containing 000000002 events
ft960727_0447_1900G204670H.fits-> Ignoring the following files containing 000000001 events
ft960727_0447_1900G208270H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300570h.prelist merge count = 4 photon cnt = 9 GISSORTSPLIT:LO:g300670h.prelist merge count = 4 photon cnt = 12 GISSORTSPLIT:LO:g300770h.prelist merge count = 5 photon cnt = 14 GISSORTSPLIT:LO:g300870h.prelist merge count = 16 photon cnt = 26476 GISSORTSPLIT:LO:g300970h.prelist merge count = 2 photon cnt = 34 GISSORTSPLIT:LO:g301070h.prelist merge count = 1 photon cnt = 812 GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 17 GISSORTSPLIT:LO:g300270l.prelist merge count = 1 photon cnt = 44 GISSORTSPLIT:LO:g300170m.prelist merge count = 3 photon cnt = 53 GISSORTSPLIT:LO:g300270m.prelist merge count = 10 photon cnt = 11940 GISSORTSPLIT:LO:g300370m.prelist merge count = 1 photon cnt = 49 GISSORTSPLIT:LO:Total filenames split = 52 GISSORTSPLIT:LO:Total split file cnt = 15 GISSORTSPLIT:LO:End program-> Creating ad84041000g300170h.unf
---- cmerge: version 1.5 ---- A total of 16 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900G300270H.fits 2 -- ft960727_0447_1900G301070H.fits 3 -- ft960727_0447_1900G302170H.fits 4 -- ft960727_0447_1900G302370H.fits 5 -- ft960727_0447_1900G303170H.fits 6 -- ft960727_0447_1900G303370H.fits 7 -- ft960727_0447_1900G304170H.fits 8 -- ft960727_0447_1900G304770H.fits 9 -- ft960727_0447_1900G306070H.fits 10 -- ft960727_0447_1900G307170H.fits 11 -- ft960727_0447_1900G307370H.fits 12 -- ft960727_0447_1900G308170H.fits 13 -- ft960727_0447_1900G309070H.fits 14 -- ft960727_0447_1900G309270H.fits 15 -- ft960727_0447_1900G309870H.fits 16 -- ft960727_0447_1900G310070H.fits Merging binary extension #: 2 1 -- ft960727_0447_1900G300270H.fits 2 -- ft960727_0447_1900G301070H.fits 3 -- ft960727_0447_1900G302170H.fits 4 -- ft960727_0447_1900G302370H.fits 5 -- ft960727_0447_1900G303170H.fits 6 -- ft960727_0447_1900G303370H.fits 7 -- ft960727_0447_1900G304170H.fits 8 -- ft960727_0447_1900G304770H.fits 9 -- ft960727_0447_1900G306070H.fits 10 -- ft960727_0447_1900G307170H.fits 11 -- ft960727_0447_1900G307370H.fits 12 -- ft960727_0447_1900G308170H.fits 13 -- ft960727_0447_1900G309070H.fits 14 -- ft960727_0447_1900G309270H.fits 15 -- ft960727_0447_1900G309870H.fits 16 -- ft960727_0447_1900G310070H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000g300270m.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900G301270M.fits 2 -- ft960727_0447_1900G301470M.fits 3 -- ft960727_0447_1900G302070M.fits 4 -- ft960727_0447_1900G305070M.fits 5 -- ft960727_0447_1900G305970M.fits 6 -- ft960727_0447_1900G306170M.fits 7 -- ft960727_0447_1900G307070M.fits 8 -- ft960727_0447_1900G308270M.fits 9 -- ft960727_0447_1900G309170M.fits 10 -- ft960727_0447_1900G309970M.fits Merging binary extension #: 2 1 -- ft960727_0447_1900G301270M.fits 2 -- ft960727_0447_1900G301470M.fits 3 -- ft960727_0447_1900G302070M.fits 4 -- ft960727_0447_1900G305070M.fits 5 -- ft960727_0447_1900G305970M.fits 6 -- ft960727_0447_1900G306170M.fits 7 -- ft960727_0447_1900G307070M.fits 8 -- ft960727_0447_1900G308270M.fits 9 -- ft960727_0447_1900G309170M.fits 10 -- ft960727_0447_1900G309970M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft960727_0447_1900G304970H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900G304970H.fits Merging binary extension #: 2 1 -- ft960727_0447_1900G304970H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000053 events
ft960727_0447_1900G301970M.fits ft960727_0447_1900G305870M.fits ft960727_0447_1900G306970M.fits-> Ignoring the following files containing 000000049 events
ft960727_0447_1900G301170M.fits-> Ignoring the following files containing 000000044 events
ft960727_0447_1900G306270L.fits-> Ignoring the following files containing 000000034 events
ft960727_0447_1900G304270H.fits ft960727_0447_1900G307570H.fits-> Ignoring the following files containing 000000017 events
ft960727_0447_1900G306370L.fits-> Ignoring the following files containing 000000014 events
ft960727_0447_1900G300970H.fits ft960727_0447_1900G303070H.fits ft960727_0447_1900G304070H.fits ft960727_0447_1900G308970H.fits ft960727_0447_1900G309770H.fits-> Ignoring the following files containing 000000012 events
ft960727_0447_1900G300870H.fits ft960727_0447_1900G302970H.fits ft960727_0447_1900G303970H.fits ft960727_0447_1900G309670H.fits-> Ignoring the following files containing 000000009 events
ft960727_0447_1900G300770H.fits ft960727_0447_1900G303870H.fits ft960727_0447_1900G308770H.fits ft960727_0447_1900G309570H.fits-> Ignoring the following files containing 000000004 events
ft960727_0447_1900G308070H.fits-> Ignoring the following files containing 000000001 events
ft960727_0447_1900G300370H.fits-> Ignoring the following files containing 000000001 events
ft960727_0447_1900G309470H.fits-> Ignoring the following files containing 000000001 events
ft960727_0447_1900G304370H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 1 photon cnt = 147 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 1 photon cnt = 431 SIS0SORTSPLIT:LO:s000301h.prelist merge count = 1 photon cnt = 72 SIS0SORTSPLIT:LO:s000401h.prelist merge count = 1 photon cnt = 53 SIS0SORTSPLIT:LO:s000501h.prelist merge count = 14 photon cnt = 220977 SIS0SORTSPLIT:LO:s000601h.prelist merge count = 5 photon cnt = 111379 SIS0SORTSPLIT:LO:s000701h.prelist merge count = 4 photon cnt = 1223 SIS0SORTSPLIT:LO:s000801l.prelist merge count = 2 photon cnt = 1240 SIS0SORTSPLIT:LO:s000901l.prelist merge count = 6 photon cnt = 2256 SIS0SORTSPLIT:LO:s001001l.prelist merge count = 1 photon cnt = 248 SIS0SORTSPLIT:LO:s001101l.prelist merge count = 1 photon cnt = 88 SIS0SORTSPLIT:LO:s001201l.prelist merge count = 2 photon cnt = 128 SIS0SORTSPLIT:LO:s001301m.prelist merge count = 11 photon cnt = 52179 SIS0SORTSPLIT:LO:s001401m.prelist merge count = 3 photon cnt = 32896 SIS0SORTSPLIT:LO:s001501m.prelist merge count = 1 photon cnt = 32 SIS0SORTSPLIT:LO:Total filenames split = 54 SIS0SORTSPLIT:LO:Total split file cnt = 15 SIS0SORTSPLIT:LO:End program-> Creating ad84041000s000101h.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S000601H.fits 2 -- ft960727_0447_1900S000801H.fits 3 -- ft960727_0447_1900S001201H.fits 4 -- ft960727_0447_1900S002001H.fits 5 -- ft960727_0447_1900S002201H.fits 6 -- ft960727_0447_1900S002401H.fits 7 -- ft960727_0447_1900S002901H.fits 8 -- ft960727_0447_1900S003101H.fits 9 -- ft960727_0447_1900S003301H.fits 10 -- ft960727_0447_1900S003801H.fits 11 -- ft960727_0447_1900S004001H.fits 12 -- ft960727_0447_1900S004701H.fits 13 -- ft960727_0447_1900S005401H.fits 14 -- ft960727_0447_1900S005601H.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S000601H.fits 2 -- ft960727_0447_1900S000801H.fits 3 -- ft960727_0447_1900S001201H.fits 4 -- ft960727_0447_1900S002001H.fits 5 -- ft960727_0447_1900S002201H.fits 6 -- ft960727_0447_1900S002401H.fits 7 -- ft960727_0447_1900S002901H.fits 8 -- ft960727_0447_1900S003101H.fits 9 -- ft960727_0447_1900S003301H.fits 10 -- ft960727_0447_1900S003801H.fits 11 -- ft960727_0447_1900S004001H.fits 12 -- ft960727_0447_1900S004701H.fits 13 -- ft960727_0447_1900S005401H.fits 14 -- ft960727_0447_1900S005601H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000s000201h.unf
---- cmerge: version 1.5 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S005701H.fits 2 -- ft960727_0447_1900S006201H.fits 3 -- ft960727_0447_1900S006401H.fits 4 -- ft960727_0447_1900S006601H.fits 5 -- ft960727_0447_1900S006801H.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S005701H.fits 2 -- ft960727_0447_1900S006201H.fits 3 -- ft960727_0447_1900S006401H.fits 4 -- ft960727_0447_1900S006601H.fits 5 -- ft960727_0447_1900S006801H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000s000301m.unf
---- cmerge: version 1.5 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S001301M.fits 2 -- ft960727_0447_1900S001501M.fits 3 -- ft960727_0447_1900S001901M.fits 4 -- ft960727_0447_1900S002601M.fits 5 -- ft960727_0447_1900S002801M.fits 6 -- ft960727_0447_1900S003501M.fits 7 -- ft960727_0447_1900S003701M.fits 8 -- ft960727_0447_1900S004201M.fits 9 -- ft960727_0447_1900S004601M.fits 10 -- ft960727_0447_1900S004901M.fits 11 -- ft960727_0447_1900S005301M.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S001301M.fits 2 -- ft960727_0447_1900S001501M.fits 3 -- ft960727_0447_1900S001901M.fits 4 -- ft960727_0447_1900S002601M.fits 5 -- ft960727_0447_1900S002801M.fits 6 -- ft960727_0447_1900S003501M.fits 7 -- ft960727_0447_1900S003701M.fits 8 -- ft960727_0447_1900S004201M.fits 9 -- ft960727_0447_1900S004601M.fits 10 -- ft960727_0447_1900S004901M.fits 11 -- ft960727_0447_1900S005301M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000s000401m.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S005801M.fits 2 -- ft960727_0447_1900S006301M.fits 3 -- ft960727_0447_1900S006701M.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S005801M.fits 2 -- ft960727_0447_1900S006301M.fits 3 -- ft960727_0447_1900S006701M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000s000501l.unf
---- cmerge: version 1.5 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S001601L.fits 2 -- ft960727_0447_1900S001801L.fits 3 -- ft960727_0447_1900S004301L.fits 4 -- ft960727_0447_1900S004501L.fits 5 -- ft960727_0447_1900S005001L.fits 6 -- ft960727_0447_1900S005201L.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S001601L.fits 2 -- ft960727_0447_1900S001801L.fits 3 -- ft960727_0447_1900S004301L.fits 4 -- ft960727_0447_1900S004501L.fits 5 -- ft960727_0447_1900S005001L.fits 6 -- ft960727_0447_1900S005201L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000s000601l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S000901L.fits 2 -- ft960727_0447_1900S001101L.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S000901L.fits 2 -- ft960727_0447_1900S001101L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000s000701h.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S002501H.fits 2 -- ft960727_0447_1900S003401H.fits 3 -- ft960727_0447_1900S004101H.fits 4 -- ft960727_0447_1900S004801H.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S002501H.fits 2 -- ft960727_0447_1900S003401H.fits 3 -- ft960727_0447_1900S004101H.fits 4 -- ft960727_0447_1900S004801H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000431 events
ft960727_0447_1900S000301H.fits-> Ignoring the following files containing 000000248 events
ft960727_0447_1900S005901L.fits-> Ignoring the following files containing 000000147 events
ft960727_0447_1900S000201H.fits-> Ignoring the following files containing 000000128 events
ft960727_0447_1900S004401L.fits ft960727_0447_1900S005101L.fits-> Ignoring the following files containing 000000088 events
ft960727_0447_1900S001001L.fits-> Ignoring the following files containing 000000072 events
ft960727_0447_1900S000401H.fits-> Ignoring the following files containing 000000053 events
ft960727_0447_1900S000501H.fits-> Ignoring the following files containing 000000032 events
ft960727_0447_1900S002701M.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 1 photon cnt = 308 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 1 photon cnt = 946 SIS1SORTSPLIT:LO:s100301h.prelist merge count = 1 photon cnt = 64 SIS1SORTSPLIT:LO:s100401h.prelist merge count = 1 photon cnt = 66 SIS1SORTSPLIT:LO:s100501h.prelist merge count = 16 photon cnt = 324801 SIS1SORTSPLIT:LO:s100601h.prelist merge count = 4 photon cnt = 1487 SIS1SORTSPLIT:LO:s100701h.prelist merge count = 2 photon cnt = 26265 SIS1SORTSPLIT:LO:s100801l.prelist merge count = 2 photon cnt = 1240 SIS1SORTSPLIT:LO:s100901l.prelist merge count = 7 photon cnt = 2504 SIS1SORTSPLIT:LO:s101001l.prelist merge count = 1 photon cnt = 88 SIS1SORTSPLIT:LO:s101101l.prelist merge count = 2 photon cnt = 128 SIS1SORTSPLIT:LO:s101201m.prelist merge count = 14 photon cnt = 85127 SIS1SORTSPLIT:LO:s101301m.prelist merge count = 1 photon cnt = 32 SIS1SORTSPLIT:LO:Total filenames split = 53 SIS1SORTSPLIT:LO:Total split file cnt = 13 SIS1SORTSPLIT:LO:End program-> Creating ad84041000s100101h.unf
---- cmerge: version 1.5 ---- A total of 16 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S100701H.fits 2 -- ft960727_0447_1900S101101H.fits 3 -- ft960727_0447_1900S101901H.fits 4 -- ft960727_0447_1900S102101H.fits 5 -- ft960727_0447_1900S102301H.fits 6 -- ft960727_0447_1900S102801H.fits 7 -- ft960727_0447_1900S103101H.fits 8 -- ft960727_0447_1900S103601H.fits 9 -- ft960727_0447_1900S103801H.fits 10 -- ft960727_0447_1900S104501H.fits 11 -- ft960727_0447_1900S105201H.fits 12 -- ft960727_0447_1900S105401H.fits 13 -- ft960727_0447_1900S105901H.fits 14 -- ft960727_0447_1900S106101H.fits 15 -- ft960727_0447_1900S106301H.fits 16 -- ft960727_0447_1900S106501H.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S100701H.fits 2 -- ft960727_0447_1900S101101H.fits 3 -- ft960727_0447_1900S101901H.fits 4 -- ft960727_0447_1900S102101H.fits 5 -- ft960727_0447_1900S102301H.fits 6 -- ft960727_0447_1900S102801H.fits 7 -- ft960727_0447_1900S103101H.fits 8 -- ft960727_0447_1900S103601H.fits 9 -- ft960727_0447_1900S103801H.fits 10 -- ft960727_0447_1900S104501H.fits 11 -- ft960727_0447_1900S105201H.fits 12 -- ft960727_0447_1900S105401H.fits 13 -- ft960727_0447_1900S105901H.fits 14 -- ft960727_0447_1900S106101H.fits 15 -- ft960727_0447_1900S106301H.fits 16 -- ft960727_0447_1900S106501H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000s100201m.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S101201M.fits 2 -- ft960727_0447_1900S101401M.fits 3 -- ft960727_0447_1900S101801M.fits 4 -- ft960727_0447_1900S102501M.fits 5 -- ft960727_0447_1900S102701M.fits 6 -- ft960727_0447_1900S103301M.fits 7 -- ft960727_0447_1900S103501M.fits 8 -- ft960727_0447_1900S104001M.fits 9 -- ft960727_0447_1900S104401M.fits 10 -- ft960727_0447_1900S104701M.fits 11 -- ft960727_0447_1900S105101M.fits 12 -- ft960727_0447_1900S105501M.fits 13 -- ft960727_0447_1900S106001M.fits 14 -- ft960727_0447_1900S106401M.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S101201M.fits 2 -- ft960727_0447_1900S101401M.fits 3 -- ft960727_0447_1900S101801M.fits 4 -- ft960727_0447_1900S102501M.fits 5 -- ft960727_0447_1900S102701M.fits 6 -- ft960727_0447_1900S103301M.fits 7 -- ft960727_0447_1900S103501M.fits 8 -- ft960727_0447_1900S104001M.fits 9 -- ft960727_0447_1900S104401M.fits 10 -- ft960727_0447_1900S104701M.fits 11 -- ft960727_0447_1900S105101M.fits 12 -- ft960727_0447_1900S105501M.fits 13 -- ft960727_0447_1900S106001M.fits 14 -- ft960727_0447_1900S106401M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000s100301h.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S100601H.fits 2 -- ft960727_0447_1900S103001H.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S100601H.fits 2 -- ft960727_0447_1900S103001H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000s100401l.unf
---- cmerge: version 1.5 ---- A total of 7 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S101501L.fits 2 -- ft960727_0447_1900S101701L.fits 3 -- ft960727_0447_1900S104101L.fits 4 -- ft960727_0447_1900S104301L.fits 5 -- ft960727_0447_1900S104801L.fits 6 -- ft960727_0447_1900S105001L.fits 7 -- ft960727_0447_1900S105601L.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S101501L.fits 2 -- ft960727_0447_1900S101701L.fits 3 -- ft960727_0447_1900S104101L.fits 4 -- ft960727_0447_1900S104301L.fits 5 -- ft960727_0447_1900S104801L.fits 6 -- ft960727_0447_1900S105001L.fits 7 -- ft960727_0447_1900S105601L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000s100501h.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S102401H.fits 2 -- ft960727_0447_1900S103201H.fits 3 -- ft960727_0447_1900S103901H.fits 4 -- ft960727_0447_1900S104601H.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S102401H.fits 2 -- ft960727_0447_1900S103201H.fits 3 -- ft960727_0447_1900S103901H.fits 4 -- ft960727_0447_1900S104601H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad84041000s100601l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft960727_0447_1900S100801L.fits 2 -- ft960727_0447_1900S101001L.fits Merging binary extension #: 2 1 -- ft960727_0447_1900S100801L.fits 2 -- ft960727_0447_1900S101001L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000946 events
ft960727_0447_1900S100301H.fits-> Ignoring the following files containing 000000308 events
ft960727_0447_1900S100201H.fits-> Ignoring the following files containing 000000128 events
ft960727_0447_1900S104201L.fits ft960727_0447_1900S104901L.fits-> Ignoring the following files containing 000000088 events
ft960727_0447_1900S100901L.fits-> Ignoring the following files containing 000000066 events
ft960727_0447_1900S100501H.fits-> Ignoring the following files containing 000000064 events
ft960727_0447_1900S100401H.fits-> Ignoring the following files containing 000000032 events
ft960727_0447_1900S102601M.fits-> Tar-ing together the leftover raw files
a ft960727_0447_1900G200370H.fits 40K a ft960727_0447_1900G200870H.fits 40K a ft960727_0447_1900G200970H.fits 40K a ft960727_0447_1900G201170M.fits 40K a ft960727_0447_1900G201970M.fits 40K a ft960727_0447_1900G202870H.fits 40K a ft960727_0447_1900G202970H.fits 40K a ft960727_0447_1900G203070H.fits 40K a ft960727_0447_1900G203870H.fits 40K a ft960727_0447_1900G203970H.fits 40K a ft960727_0447_1900G204670H.fits 40K a ft960727_0447_1900G204770H.fits 40K a ft960727_0447_1900G204870H.fits 40K a ft960727_0447_1900G205370M.fits 40K a ft960727_0447_1900G206070M.fits 40K a ft960727_0447_1900G206470L.fits 40K a ft960727_0447_1900G206570L.fits 40K a ft960727_0447_1900G207170M.fits 40K a ft960727_0447_1900G207670H.fits 40K a ft960727_0447_1900G208170H.fits 40K a ft960727_0447_1900G208270H.fits 40K a ft960727_0447_1900G208370H.fits 40K a ft960727_0447_1900G208470H.fits 40K a ft960727_0447_1900G209270H.fits 40K a ft960727_0447_1900G209370H.fits 40K a ft960727_0447_1900G209770H.fits 40K a ft960727_0447_1900G209870H.fits 40K a ft960727_0447_1900G210070H.fits 40K a ft960727_0447_1900G210170H.fits 40K a ft960727_0447_1900G300370H.fits 40K a ft960727_0447_1900G300770H.fits 40K a ft960727_0447_1900G300870H.fits 40K a ft960727_0447_1900G300970H.fits 40K a ft960727_0447_1900G301170M.fits 40K a ft960727_0447_1900G301970M.fits 40K a ft960727_0447_1900G302970H.fits 40K a ft960727_0447_1900G303070H.fits 40K a ft960727_0447_1900G303870H.fits 40K a ft960727_0447_1900G303970H.fits 40K a ft960727_0447_1900G304070H.fits 40K a ft960727_0447_1900G304270H.fits 40K a ft960727_0447_1900G304370H.fits 40K a ft960727_0447_1900G305870M.fits 40K a ft960727_0447_1900G306270L.fits 40K a ft960727_0447_1900G306370L.fits 40K a ft960727_0447_1900G306970M.fits 40K a ft960727_0447_1900G307570H.fits 40K a ft960727_0447_1900G308070H.fits 40K a ft960727_0447_1900G308770H.fits 40K a ft960727_0447_1900G308970H.fits 40K a ft960727_0447_1900G309470H.fits 40K a ft960727_0447_1900G309570H.fits 40K a ft960727_0447_1900G309670H.fits 40K a ft960727_0447_1900G309770H.fits 40K a ft960727_0447_1900S000201H.fits 45K a ft960727_0447_1900S000301H.fits 54K a ft960727_0447_1900S000401H.fits 40K a ft960727_0447_1900S000501H.fits 40K a ft960727_0447_1900S001001L.fits 43K a ft960727_0447_1900S002701M.fits 40K a ft960727_0447_1900S004401L.fits 40K a ft960727_0447_1900S005101L.fits 43K a ft960727_0447_1900S005901L.fits 48K a ft960727_0447_1900S100201H.fits 51K a ft960727_0447_1900S100301H.fits 76K a ft960727_0447_1900S100401H.fits 40K a ft960727_0447_1900S100501H.fits 40K a ft960727_0447_1900S100901L.fits 43K a ft960727_0447_1900S102601M.fits 40K a ft960727_0447_1900S104201L.fits 40K a ft960727_0447_1900S104901L.fits 43K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft960727_0447.1900 'ft960727_0447.1900' is successfully opened Data Start Time is 112596433.90 (960727 044713) Time Margin 2.0 sec included Sync error detected in 11175 th SF Sync error detected in 11176 th SF Sync error detected in 11221 th SF Sync error detected in 11416 th SF Sync error detected in 11417 th SF Sync error detected in 11418 th SF Sync error detected in 11419 th SF Sync error detected in 11494 th SF 'ft960727_0447.1900' EOF detected, sf=12954 Data End Time is 112647637.72 (960727 190037) Gain History is written in ft960727_0447_1900.ghf-> Checking if column CAL_START in ft960727_0447_1900.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft960727_0447_1900.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad84041000g200270m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000g200370h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000g300170h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000g300270m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000g300370h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000201h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000202h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000212h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000301m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000302m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000312m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000401m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000402m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000412m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000501l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000502l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000512l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000601l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s000701h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100201m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100202m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100212m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100301h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100302h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100312h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100401l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100402l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100412l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100501h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad84041000s100601l.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 96/ 7/27 4:47 mjd=50291.199306 Orbit file name is ./frf.orbit.215 Epoch of Orbital Elements: 1996/7/22 14:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa960727_0447.1900 S0-HK file: ft960727_0447_1900S0HK.fits S1-HK file: ft960727_0447_1900S1HK.fits G2-HK file: ft960727_0447_1900G2HK.fits G3-HK file: ft960727_0447_1900G3HK.fits output FITS File: ft960727_0447_1900.mkf Total 1601 Data bins were processed.-> Checking if column TIME in ft960727_0447_1900.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 7990.1880 The mean of the selected column is 24.509779 The standard deviation of the selected column is 7.5599563 The minimum of selected column is 7.5227580 The maximum of selected column is 55.375195 The number of points used in calculation is 326-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 6594.7248 The mean of the selected column is 20.229217 The standard deviation of the selected column is 7.6928095 The minimum of selected column is 7.1250253 The maximum of selected column is 69.156494 The number of points used in calculation is 326-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>1.8 && S0_PIXL0<47.1 )&& (S0_PIXL1>0.0 && S0_PIXL1<43.3 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:57:51 0.14E+05 172092 1100
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
160351 120557 0 39794 0 0
Writing events file
120557 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
160351 120557 0 39794 0 0
in 10292.25 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 120557
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 74 73867
Flickering pixels iter, pixels & cnts : 1 37 2176
cleaning chip # 1
Hot pixels & counts : 44 36097
Flickering pixels iter, pixels & cnts : 1 23 584
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 178
Number of (internal) image counts : 120557
Number of image cts rejected (N, %) : 112724 93.5026550
By chip : 0 1 2 3
Pixels rejected : 111 67 0 0
Image counts : 77307 43250 0 0
Image cts rejected: 76043 36681 0 0
Image cts rej (%) : 98.36 84.81 0.00 0.00
filtering data...
Total counts : 77307 43250 0 0
Total cts rejected: 76043 36681 0 0
Total cts rej (%) : 98.36 84.81 0.00 0.00
Number of clean counts accepted : 7833
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 178
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad84041000s000102h.evt use_events=no
Wrote cleaned events file to ad84041000s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad84041000s000112h.unf into ad84041000s000112h.evtThe sum of the selected column is 7990.1880 The mean of the selected column is 24.509779 The standard deviation of the selected column is 7.5599563 The minimum of selected column is 7.5227580 The maximum of selected column is 55.375195 The number of points used in calculation is 326-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 6594.7248 The mean of the selected column is 20.229217 The standard deviation of the selected column is 7.6928095 The minimum of selected column is 7.1250253 The maximum of selected column is 69.156494 The number of points used in calculation is 326-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>1.8 && S0_PIXL0<47.1 )&& (S0_PIXL1>0.0 && S0_PIXL1<43.3 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 04:57:51 0.14E+05 172803 1100
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
161291 121224 0 40067 0 0
Writing events file
121224 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
161291 121224 0 40067 0 0
in 10292.25 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 121224
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 75 74386
Flickering pixels iter, pixels & cnts : 1 36 2027
cleaning chip # 1
Hot pixels & counts : 44 36221
Flickering pixels iter, pixels & cnts : 1 23 584
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 178
Number of (internal) image counts : 121224
Number of image cts rejected (N, %) : 113218 93.3956985
By chip : 0 1 2 3
Pixels rejected : 111 67 0 0
Image counts : 77727 43497 0 0
Image cts rejected: 76413 36805 0 0
Image cts rej (%) : 98.31 84.62 0.00 0.00
filtering data...
Total counts : 77727 43497 0 0
Total cts rejected: 76413 36805 0 0
Total cts rej (%) : 98.31 84.62 0.00 0.00
Number of clean counts accepted : 8006
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 178
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad84041000s000112h.evt use_events=no
Wrote cleaned events file to ad84041000s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad84041000s000201h.unf because of modeThe sum of the selected column is 4161.8926 The mean of the selected column is 28.506114 The standard deviation of the selected column is 18.384918 The minimum of selected column is 12.875046 The maximum of selected column is 185.31316 The number of points used in calculation is 146-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3522.6686 The mean of the selected column is 24.127867 The standard deviation of the selected column is 19.169555 The minimum of selected column is 8.8125315 The maximum of selected column is 186.00067 The number of points used in calculation is 146-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<83.6 )&& (S0_PIXL1>0.0 && S0_PIXL1<81.6 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 14:43:39 0.63E+04 77564 1100
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s000202h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
72021 54263 0 17758 0 0
Writing events file
54263 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
72021 54263 0 17758 0 0
in 4617.66 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 54263
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 73 33098
Flickering pixels iter, pixels & cnts : 1 34 1099
Flickering pixels iter, pixels & cnts : 2 1 4
cleaning chip # 1
Hot pixels & counts : 42 16047
Flickering pixels iter, pixels & cnts : 1 15 397
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 165
Number of (internal) image counts : 54263
Number of image cts rejected (N, %) : 50645 93.3324738
By chip : 0 1 2 3
Pixels rejected : 108 57 0 0
Image counts : 34799 19464 0 0
Image cts rejected: 34201 16444 0 0
Image cts rej (%) : 98.28 84.48 0.00 0.00
filtering data...
Total counts : 34799 19464 0 0
Total cts rejected: 34201 16444 0 0
Total cts rej (%) : 98.28 84.48 0.00 0.00
Number of clean counts accepted : 3618
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 165
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad84041000s000202h.evt use_events=no
Wrote cleaned events file to ad84041000s000202h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad84041000s000212h.unf into ad84041000s000212h.evtThe sum of the selected column is 4161.8926 The mean of the selected column is 28.506114 The standard deviation of the selected column is 18.384918 The minimum of selected column is 12.875046 The maximum of selected column is 185.31316 The number of points used in calculation is 146-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3522.6686 The mean of the selected column is 24.127867 The standard deviation of the selected column is 19.169555 The minimum of selected column is 8.8125315 The maximum of selected column is 186.00067 The number of points used in calculation is 146-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<83.6 )&& (S0_PIXL1>0.0 && S0_PIXL1<81.6 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 14:43:39 0.63E+04 77873 1100
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s000212h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
72479 54581 0 17898 0 0
Writing events file
54581 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
72479 54581 0 17898 0 0
in 4617.66 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 54581
Total counts in chip images : 54580
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 73 33236
Flickering pixels iter, pixels & cnts : 1 34 1125
Flickering pixels iter, pixels & cnts : 2 1 4
cleaning chip # 1
Hot pixels & counts : 42 16114
Flickering pixels iter, pixels & cnts : 1 15 397
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 165
Number of (internal) image counts : 54580
Number of image cts rejected (N, %) : 50876 93.2136307
By chip : 0 1 2 3
Pixels rejected : 108 57 0 0
Image counts : 34994 19586 0 0
Image cts rejected: 34365 16511 0 0
Image cts rej (%) : 98.20 84.30 0.00 0.00
filtering data...
Total counts : 34994 19587 0 0
Total cts rejected: 34365 16512 0 0
Total cts rej (%) : 98.20 84.30 0.00 0.00
Number of clean counts accepted : 3704
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 165
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad84041000s000212h.evt use_events=no
Wrote cleaned events file to ad84041000s000212h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad84041000s000301m.unf because of modeThe sum of the selected column is 2617.4780 The mean of the selected column is 24.235907 The standard deviation of the selected column is 11.211108 The minimum of selected column is 8.5000305 The maximum of selected column is 106.06287 The number of points used in calculation is 108-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0.0 && S0_PIXL1<57.8 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT MEDIUM 27/07/96 06:24:59 0.88E+04 36994 1100
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s000302m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
33798 227 0 33571 0 0
Writing events file
227 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
33798 227 0 33571 0 0
in 51.28 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 227
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 10 53
Flickering pixels iter, pixels & cnts : 1 19 67
cleaning chip # 1
Hot pixels & counts : 4 18
Flickering pixels iter, pixels & cnts : 1 2 6
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 35
Number of (internal) image counts : 227
Number of image cts rejected (N, %) : 144 63.4361229
By chip : 0 1 2 3
Pixels rejected : 29 6 0 0
Image counts : 148 79 0 0
Image cts rejected: 120 24 0 0
Image cts rej (%) : 81.08 30.38 0.00 0.00
filtering data...
Total counts : 148 79 0 0
Total cts rejected: 120 24 0 0
Total cts rej (%) : 81.08 30.38 0.00 0.00
Number of clean counts accepted : 83
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 35
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s000302m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad84041000s000302m.evt use_events=no
Wrote cleaned events file to ad84041000s000302m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad84041000s000312m.unf into ad84041000s000312m.evtThe sum of the selected column is 2617.4780 The mean of the selected column is 24.235907 The standard deviation of the selected column is 11.211108 The minimum of selected column is 8.5000305 The maximum of selected column is 106.06287 The number of points used in calculation is 108-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0.0 && S0_PIXL1<57.8 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 MEDIUM 27/07/96 06:24:59 0.88E+04 37178 1100
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s000312m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
34078 227 0 33851 0 0
Writing events file
227 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
34078 227 0 33851 0 0
in 51.28 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 227
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 10 53
Flickering pixels iter, pixels & cnts : 1 19 67
cleaning chip # 1
Hot pixels & counts : 4 18
Flickering pixels iter, pixels & cnts : 1 2 6
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 35
Number of (internal) image counts : 227
Number of image cts rejected (N, %) : 144 63.4361229
By chip : 0 1 2 3
Pixels rejected : 29 6 0 0
Image counts : 148 79 0 0
Image cts rejected: 120 24 0 0
Image cts rej (%) : 81.08 30.38 0.00 0.00
filtering data...
Total counts : 148 79 0 0
Total cts rejected: 120 24 0 0
Total cts rej (%) : 81.08 30.38 0.00 0.00
Number of clean counts accepted : 83
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 35
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s000312m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad84041000s000312m.evt use_events=no
Wrote cleaned events file to ad84041000s000312m.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad84041000s000401m.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT MEDIUM 27/07/96 14:50:19 0.64E+04 22085 1100
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s000402m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s000402m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad84041000s000402m.evt use_events=no
Wrote cleaned events file to ad84041000s000402m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad84041000s000402m.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 MEDIUM 27/07/96 14:50:19 0.64E+04 22211 1100
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s000412m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s000412m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad84041000s000412m.evt use_events=no
Wrote cleaned events file to ad84041000s000412m.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad84041000s000412m.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT LOW 27/07/96 07:01:31 0.12E+04 1013 1100
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s000502l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s000502l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad84041000s000502l.evt use_events=no
Wrote cleaned events file to ad84041000s000502l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad84041000s000502l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 LOW 27/07/96 07:01:31 0.12E+04 1034 1100
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s000512l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s000512l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad84041000s000512l.evt use_events=no
Wrote cleaned events file to ad84041000s000512l.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad84041000s000512l.evt since it contains 0 eventsThe sum of the selected column is 14140.770 The mean of the selected column is 32.065239 The standard deviation of the selected column is 23.471793 The minimum of selected column is 7.8571701 The maximum of selected column is 415.22025 The number of points used in calculation is 441-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 15031.410 The mean of the selected column is 34.084831 The standard deviation of the selected column is 22.284046 The minimum of selected column is 11.107182 The maximum of selected column is 341.96997 The number of points used in calculation is 441-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<102.4 )&& (S1_PIXL3>0.0 && S1_PIXL3<100.9 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 05:25:19 0.18E+05 231436 0011
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
215922 168377 0 47545 0 0
Writing events file
168377 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
215922 168377 0 47545 0 0
in 14161.83 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 168377
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 59 79060
Flickering pixels iter, pixels & cnts : 1 46 2505
cleaning chip # 3
Hot pixels & counts : 55 75126
Flickering pixels iter, pixels & cnts : 1 42 2524
Number of pixels rejected : 202
Number of (internal) image counts : 168377
Number of image cts rejected (N, %) : 159215 94.5586395
By chip : 0 1 2 3
Pixels rejected : 0 0 105 97
Image counts : 0 0 83876 84501
Image cts rejected: 0 0 81565 77650
Image cts rej (%) : 0.00 0.00 97.24 91.89
filtering data...
Total counts : 0 0 83876 84501
Total cts rejected: 0 0 81565 77650
Total cts rej (%) : 0.00 0.00 97.24 91.89
Number of clean counts accepted : 9162
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 202
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad84041000s100102h.evt use_events=no
Wrote cleaned events file to ad84041000s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad84041000s100112h.unf into ad84041000s100112h.evtThe sum of the selected column is 14140.770 The mean of the selected column is 32.065239 The standard deviation of the selected column is 23.471793 The minimum of selected column is 7.8571701 The maximum of selected column is 415.22025 The number of points used in calculation is 441-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 15031.410 The mean of the selected column is 34.084831 The standard deviation of the selected column is 22.284046 The minimum of selected column is 11.107182 The maximum of selected column is 341.96997 The number of points used in calculation is 441-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<102.4 )&& (S1_PIXL3>0.0 && S1_PIXL3<100.9 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 05:25:19 0.18E+05 232286 0011
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
218038 169928 0 48110 0 0
Writing events file
169928 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
218038 169928 0 48110 0 0
in 14161.83 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 169928
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 59 79541
Flickering pixels iter, pixels & cnts : 1 46 2527
cleaning chip # 3
Hot pixels & counts : 56 76064
Flickering pixels iter, pixels & cnts : 1 42 2413
Number of pixels rejected : 203
Number of (internal) image counts : 169928
Number of image cts rejected (N, %) : 160545 94.4782486
By chip : 0 1 2 3
Pixels rejected : 0 0 105 98
Image counts : 0 0 84473 85455
Image cts rejected: 0 0 82068 78477
Image cts rej (%) : 0.00 0.00 97.15 91.83
filtering data...
Total counts : 0 0 84473 85455
Total cts rejected: 0 0 82068 78477
Total cts rej (%) : 0.00 0.00 97.15 91.83
Number of clean counts accepted : 9383
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 203
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad84041000s100112h.evt use_events=no
Wrote cleaned events file to ad84041000s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad84041000s100201m.unf because of modeThe sum of the selected column is 3735.4194 The mean of the selected column is 34.910462 The standard deviation of the selected column is 14.785386 The minimum of selected column is 12.218794 The maximum of selected column is 116.25041 The number of points used in calculation is 107-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3966.4515 The mean of the selected column is 37.419353 The standard deviation of the selected column is 14.480672 The minimum of selected column is 11.437541 The maximum of selected column is 84.406540 The number of points used in calculation is 106-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<79.2 )&& (S1_PIXL3>0.0 && S1_PIXL3<80.8 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT MEDIUM 27/07/96 06:24:59 0.15E+05 57567 0011
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s100202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
54750 13489 0 41261 0 0
Writing events file
13489 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
54750 13489 0 41261 0 0
in 3389.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 13489
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 25 5283
Flickering pixels iter, pixels & cnts : 1 13 167
cleaning chip # 3
Hot pixels & counts : 22 5866
Flickering pixels iter, pixels & cnts : 1 13 125
Number of pixels rejected : 73
Number of (internal) image counts : 13489
Number of image cts rejected (N, %) : 11441 84.8172607
By chip : 0 1 2 3
Pixels rejected : 0 0 38 35
Image counts : 0 0 5928 7561
Image cts rejected: 0 0 5450 5991
Image cts rej (%) : 0.00 0.00 91.94 79.24
filtering data...
Total counts : 0 0 5928 7561
Total cts rejected: 0 0 5450 5991
Total cts rej (%) : 0.00 0.00 91.94 79.24
Number of clean counts accepted : 2048
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 73
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad84041000s100202m.evt use_events=no
Wrote cleaned events file to ad84041000s100202m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad84041000s100212m.unf into ad84041000s100212m.evtThe sum of the selected column is 3735.4194 The mean of the selected column is 34.910462 The standard deviation of the selected column is 14.785386 The minimum of selected column is 12.218794 The maximum of selected column is 116.25041 The number of points used in calculation is 107-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3966.4515 The mean of the selected column is 37.419353 The standard deviation of the selected column is 14.480672 The minimum of selected column is 11.437541 The maximum of selected column is 84.406540 The number of points used in calculation is 106-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<79.2 )&& (S1_PIXL3>0.0 && S1_PIXL3<80.8 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 MEDIUM 27/07/96 06:24:59 0.15E+05 57774 0011
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s100212m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
55261 13605 0 41656 0 0
Writing events file
13605 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
55261 13605 0 41656 0 0
in 3389.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 13605
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 25 5316
Flickering pixels iter, pixels & cnts : 1 13 168
cleaning chip # 3
Hot pixels & counts : 22 5915
Flickering pixels iter, pixels & cnts : 1 13 130
Number of pixels rejected : 73
Number of (internal) image counts : 13605
Number of image cts rejected (N, %) : 11529 84.7409058
By chip : 0 1 2 3
Pixels rejected : 0 0 38 35
Image counts : 0 0 5969 7636
Image cts rejected: 0 0 5484 6045
Image cts rej (%) : 0.00 0.00 91.87 79.16
filtering data...
Total counts : 0 0 5969 7636
Total cts rejected: 0 0 5484 6045
Total cts rej (%) : 0.00 0.00 91.87 79.16
Number of clean counts accepted : 2076
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 73
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s100212m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad84041000s100212m.evt use_events=no
Wrote cleaned events file to ad84041000s100212m.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad84041000s100301h.unf because of modeThe sum of the selected column is 1083.1466 The mean of the selected column is 37.349883 The standard deviation of the selected column is 15.019706 The minimum of selected column is 5.8928776 The maximum of selected column is 86.844048 The number of points used in calculation is 29-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 880.44055 The mean of the selected column is 30.360019 The standard deviation of the selected column is 8.2011551 The minimum of selected column is 11.375039 The maximum of selected column is 45.968906 The number of points used in calculation is 29-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<82.4 )&& (S1_PIXL3>5.7 && S1_PIXL3<54.9 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:58:27 0.16E+04 20616 0011
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s100302h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
19323 10451 0 8872 0 0
Writing events file
10451 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
19323 10451 0 8872 0 0
in 880.06 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 10451
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 55 4807
Flickering pixels iter, pixels & cnts : 1 20 169
cleaning chip # 3
Hot pixels & counts : 51 4639
Flickering pixels iter, pixels & cnts : 1 23 234
Number of pixels rejected : 149
Number of (internal) image counts : 10451
Number of image cts rejected (N, %) : 9849 94.2397842
By chip : 0 1 2 3
Pixels rejected : 0 0 75 74
Image counts : 0 0 5125 5326
Image cts rejected: 0 0 4976 4873
Image cts rej (%) : 0.00 0.00 97.09 91.49
filtering data...
Total counts : 0 0 5125 5326
Total cts rejected: 0 0 4976 4873
Total cts rej (%) : 0.00 0.00 97.09 91.49
Number of clean counts accepted : 602
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 149
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s100302h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad84041000s100302h.evt use_events=no
Wrote cleaned events file to ad84041000s100302h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad84041000s100312h.unf into ad84041000s100312h.evtThe sum of the selected column is 1083.1466 The mean of the selected column is 37.349883 The standard deviation of the selected column is 15.019706 The minimum of selected column is 5.8928776 The maximum of selected column is 86.844048 The number of points used in calculation is 29-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 880.44055 The mean of the selected column is 30.360019 The standard deviation of the selected column is 8.2011551 The minimum of selected column is 11.375039 The maximum of selected column is 45.968906 The number of points used in calculation is 29-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0.0 && S1_PIXL2<82.4 )&& (S1_PIXL3>5.7 && S1_PIXL3<54.9 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 04:58:27 0.16E+04 20665 0011
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s100312h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
19479 10535 0 8944 0 0
Writing events file
10535 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
19479 10535 0 8944 0 0
in 880.06 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 10535
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 55 4830
Flickering pixels iter, pixels & cnts : 1 20 170
cleaning chip # 3
Hot pixels & counts : 52 4695
Flickering pixels iter, pixels & cnts : 1 22 223
Number of pixels rejected : 149
Number of (internal) image counts : 10535
Number of image cts rejected (N, %) : 9918 94.1433334
By chip : 0 1 2 3
Pixels rejected : 0 0 75 74
Image counts : 0 0 5157 5378
Image cts rejected: 0 0 5000 4918
Image cts rej (%) : 0.00 0.00 96.96 91.45
filtering data...
Total counts : 0 0 5157 5378
Total cts rejected: 0 0 5000 4918
Total cts rej (%) : 0.00 0.00 96.96 91.45
Number of clean counts accepted : 617
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 149
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s100312h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad84041000s100312h.evt use_events=no
Wrote cleaned events file to ad84041000s100312h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad84041000s100401l.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT LOW 27/07/96 07:01:31 0.13E+04 1370 0011
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s100402l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s100402l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad84041000s100402l.evt use_events=no
Wrote cleaned events file to ad84041000s100402l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad84041000s100402l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 LOW 27/07/96 07:01:31 0.13E+04 1382 0011
Processing file: /data/data24/seq_proc/84041000.005/ad84041000s100412l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/84041000.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/84041000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/84041000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000s100412l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad84041000s100412l.evt use_events=no
Wrote cleaned events file to ad84041000s100412l.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad84041000s100412l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.19E+05 26903 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200170h.unf
Total Good Bad: Region Time Phase Cut
26903 15169 10384 1350 0 0
Writing events file
15169 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26903 15169 10384 1350 0 0
in 15186.54 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
15169 14508 661
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad84041000g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 14508 in ad84041000g200170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.13E+05 12274 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200270m.unf
Total Good Bad: Region Time Phase Cut
12274 4292 6320 1662 0 0
Writing events file
4292 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12274 4292 6320 1662 0 0
in 4287.75 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
4292 4093 199
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad84041000g200270m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 4093 in ad84041000g200270m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 912 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200370h.unf
Total Good Bad: Region Time Phase Cut
912 607 305 0 0 0
Writing events file
607 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
912 607 305 0 0 0
in 566.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
607 580 27
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000g200370h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad84041000g200370h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 580 in ad84041000g200370h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.19E+05 26476 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300170h.unf
Total Good Bad: Region Time Phase Cut
26476 16212 8737 1527 0 0
Writing events file
16212 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26476 16212 8737 1527 0 0
in 15180.54 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
16212 15430 782
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad84041000g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 15430 in ad84041000g300170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.13E+05 11940 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300270m.unf
Total Good Bad: Region Time Phase Cut
11940 4525 5622 1793 0 0
Writing events file
4525 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11940 4525 5622 1793 0 0
in 4287.75 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
4525 4310 215
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad84041000g300270m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 4310 in ad84041000g300270m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 812 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300370h.unf
Total Good Bad: Region Time Phase Cut
812 576 236 0 0 0
Writing events file
576 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
812 576 236 0 0 0
in 566.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
576 549 27
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!screen:ASCA > read events ad84041000g300370h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad84041000g300370h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 549 in ad84041000g300370h.unf-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad84041000g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960727_0447.1900
making an exposure map...
Aspect RA/DEC/ROLL : 203.2880 -31.6987 66.7104
Mean RA/DEC/ROLL : 203.3045 -31.6820 66.7104
Pnt RA/DEC/ROLL : 203.3686 -31.7921 66.7104
Image rebin factor : 1
Attitude Records : 51527
GTI intervals : 33
Total GTI (secs) : 15186.544
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3278.0322266 3278.0322266
20 Percent Complete: Total/live time: 3278.0322266 3278.0322266
30 Percent Complete: Total/live time: 5630.0888672 5630.0888672
40 Percent Complete: Total/live time: 6930.0844727 6930.0844727
50 Percent Complete: Total/live time: 8064.5805664 8064.5805664
60 Percent Complete: Total/live time: 10252.0742188 10252.0742188
70 Percent Complete: Total/live time: 12194.2119141 12194.2119141
80 Percent Complete: Total/live time: 12558.2109375 12558.2109375
90 Percent Complete: Total/live time: 14210.2060547 14210.2060547
100 Percent Complete: Total/live time: 15186.5429688 15186.5429688
Number of attitude steps used: 26
Number of attitude steps avail: 34039
Mean RA/DEC pixel offset: -9.5755 -3.6035
writing expo file: ad84041000g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad84041000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad84041000g200170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 14508 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200170h.evt
Total Good Bad: Region Time Phase Cut
14508 14399 109 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14508 14399 109 0 0 0
in 15186.54 seconds
Image has 14399 counts for 0.9481 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200170h.evt
Total Good Bad: Region Time Phase Cut
14508 7455 109 0 0 6944
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14508 7455 109 0 0 6944
in 15186.54 seconds
Image has 7455 counts for 0.4909 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200170h.evt
Total Good Bad: Region Time Phase Cut
14508 6989 109 0 0 7410
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14508 6989 109 0 0 7410
in 15186.54 seconds
Image has 6989 counts for 0.4602 counts/sec
Command not found; type ? for a command listing
!ad84041000g200170h:ASCA >
!ad84041000g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad84041000g200170h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!ad84041000g200170h:ASCA > read events ad84041000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!ad84041000g200170h:ASCA-GIS2-PH > set image sky
!ad84041000g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad84041000g200170h:ASCA-GIS2-PH > extract image
!ad84041000g200170h:ASCA-GIS2-PH > save image outfile=ad84041000g200170h.img
Wrote image to file ad84041000g200170h.img
!ad84041000g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad84041000g200170h:ASCA-GIS2-PH > extract image
!ad84041000g200170h:ASCA-GIS2-PH > save image outfile=ad84041000g200170h_lo.img
Wrote image to file ad84041000g200170h_lo.img
!ad84041000g200170h:ASCA-GIS2-PH > clear pha_cut
!ad84041000g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad84041000g200170h:ASCA-GIS2-PH > extract image
!ad84041000g200170h:ASCA-GIS2-PH > save image outfile=ad84041000g200170h_hi.img
Wrote image to file ad84041000g200170h_hi.img
!ad84041000g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad84041000g200270m.expo
ASCAEXPO_V0.9b
reading data file: ad84041000g200270m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960727_0447.1900
making an exposure map...
Aspect RA/DEC/ROLL : 203.2880 -31.6987 66.7093
Mean RA/DEC/ROLL : 203.3066 -31.6839 66.7093
Pnt RA/DEC/ROLL : 203.2652 -31.7102 66.7093
Image rebin factor : 1
Attitude Records : 51527
GTI intervals : 9
Total GTI (secs) : 4287.746
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 904.9969482 904.9969482
20 Percent Complete: Total/live time: 904.9969482 904.9969482
30 Percent Complete: Total/live time: 2332.0170898 2332.0170898
40 Percent Complete: Total/live time: 2332.0170898 2332.0170898
50 Percent Complete: Total/live time: 2345.0170898 2345.0170898
60 Percent Complete: Total/live time: 2680.1010742 2680.1010742
70 Percent Complete: Total/live time: 3508.2031250 3508.2031250
80 Percent Complete: Total/live time: 3508.2031250 3508.2031250
90 Percent Complete: Total/live time: 3908.9184570 3908.9184570
100 Percent Complete: Total/live time: 4287.7456055 4287.7456055
Number of attitude steps used: 23
Number of attitude steps avail: 10735
Mean RA/DEC pixel offset: -9.3393 -3.8334
writing expo file: ad84041000g200270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad84041000g200270m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad84041000g200270m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.43E+04 4093 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200270m.evt
Total Good Bad: Region Time Phase Cut
4093 4063 30 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4093 4063 30 0 0 0
in 4287.75 seconds
Image has 4063 counts for 0.9476 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200270m.evt
Total Good Bad: Region Time Phase Cut
4093 2072 30 0 0 1991
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4093 2072 30 0 0 1991
in 4287.75 seconds
Image has 2072 counts for 0.4832 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200270m.evt
Total Good Bad: Region Time Phase Cut
4093 2007 30 0 0 2056
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4093 2007 30 0 0 2056
in 4287.75 seconds
Image has 2007 counts for 0.4681 counts/sec
Command not found; type ? for a command listing
!ad84041000g200270m:ASCA >
!ad84041000g200270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad84041000g200270m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!ad84041000g200270m:ASCA > read events ad84041000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!ad84041000g200270m:ASCA-GIS2-PH > set image sky
!ad84041000g200270m:ASCA-GIS2-PH > filter region corner_point.reg
!ad84041000g200270m:ASCA-GIS2-PH > extract image
!ad84041000g200270m:ASCA-GIS2-PH > save image outfile=ad84041000g200270m.img
Wrote image to file ad84041000g200270m.img
!ad84041000g200270m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad84041000g200270m:ASCA-GIS2-PH > extract image
!ad84041000g200270m:ASCA-GIS2-PH > save image outfile=ad84041000g200270m_lo.img
Wrote image to file ad84041000g200270m_lo.img
!ad84041000g200270m:ASCA-GIS2-PH > clear pha_cut
!ad84041000g200270m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad84041000g200270m:ASCA-GIS2-PH > extract image
!ad84041000g200270m:ASCA-GIS2-PH > save image outfile=ad84041000g200270m_hi.img
Wrote image to file ad84041000g200270m_hi.img
!ad84041000g200270m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad84041000g200370h.expo
ASCAEXPO_V0.9b
reading data file: ad84041000g200370h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960727_0447.1900
making an exposure map...
Aspect RA/DEC/ROLL : 203.2880 -31.6987 66.7101
Mean RA/DEC/ROLL : 203.3049 -31.6820 66.7101
Pnt RA/DEC/ROLL : 203.2703 -31.7173 66.7101
Image rebin factor : 1
Attitude Records : 51527
GTI intervals : 4
Total GTI (secs) : 565.998
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 565.9980469 565.9980469
100 Percent Complete: Total/live time: 565.9980469 565.9980469
Number of attitude steps used: 2
Number of attitude steps avail: 1142
Mean RA/DEC pixel offset: -5.1429 -1.6191
writing expo file: ad84041000g200370h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad84041000g200370h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad84041000g200370h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 580 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200370h.evt
Total Good Bad: Region Time Phase Cut
580 577 3 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
580 577 3 0 0 0
in 566.00 seconds
Image has 577 counts for 1.019 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200370h.evt
Total Good Bad: Region Time Phase Cut
580 276 3 0 0 301
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
580 276 3 0 0 301
in 566.00 seconds
Image has 276 counts for 0.4876 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200370h.evt
Total Good Bad: Region Time Phase Cut
580 303 3 0 0 274
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
580 303 3 0 0 274
in 566.00 seconds
Image has 303 counts for 0.5353 counts/sec
Command not found; type ? for a command listing
!ad84041000g200370h:ASCA >
!ad84041000g200370h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad84041000g200370h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!ad84041000g200370h:ASCA > read events ad84041000g200370h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!ad84041000g200370h:ASCA-GIS2-PH > set image sky
!ad84041000g200370h:ASCA-GIS2-PH > filter region corner_point.reg
!ad84041000g200370h:ASCA-GIS2-PH > extract image
!ad84041000g200370h:ASCA-GIS2-PH > save image outfile=ad84041000g200370h.img
Wrote image to file ad84041000g200370h.img
!ad84041000g200370h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad84041000g200370h:ASCA-GIS2-PH > extract image
!ad84041000g200370h:ASCA-GIS2-PH > save image outfile=ad84041000g200370h_lo.img
Wrote image to file ad84041000g200370h_lo.img
!ad84041000g200370h:ASCA-GIS2-PH > clear pha_cut
!ad84041000g200370h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad84041000g200370h:ASCA-GIS2-PH > extract image
!ad84041000g200370h:ASCA-GIS2-PH > save image outfile=ad84041000g200370h_hi.img
Wrote image to file ad84041000g200370h_hi.img
!ad84041000g200370h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad84041000g300170h.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad84041000g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960727_0447.1900
making an exposure map...
Aspect RA/DEC/ROLL : 203.2880 -31.6987 66.7179
Mean RA/DEC/ROLL : 203.2903 -31.7037 66.7179
Pnt RA/DEC/ROLL : 203.3827 -31.7703 66.7179
Image rebin factor : 1
Attitude Records : 51527
GTI intervals : 33
Total GTI (secs) : 15180.544
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3276.0322266 3276.0322266
20 Percent Complete: Total/live time: 3276.0322266 3276.0322266
30 Percent Complete: Total/live time: 5628.0888672 5628.0888672
40 Percent Complete: Total/live time: 6928.0844727 6928.0844727
50 Percent Complete: Total/live time: 8062.5805664 8062.5805664
60 Percent Complete: Total/live time: 10250.0742188 10250.0742188
70 Percent Complete: Total/live time: 12190.2119141 12190.2119141
80 Percent Complete: Total/live time: 12554.2109375 12554.2109375
90 Percent Complete: Total/live time: 14204.2060547 14204.2060547
100 Percent Complete: Total/live time: 15180.5429688 15180.5429688
Number of attitude steps used: 26
Number of attitude steps avail: 34031
Mean RA/DEC pixel offset: 2.0384 -2.4496
writing expo file: ad84041000g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad84041000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad84041000g300170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 15430 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300170h.evt
Total Good Bad: Region Time Phase Cut
15430 15341 89 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15430 15341 89 0 0 0
in 15180.54 seconds
Image has 15341 counts for 1.011 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300170h.evt
Total Good Bad: Region Time Phase Cut
15430 8035 89 0 0 7306
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15430 8035 89 0 0 7306
in 15180.54 seconds
Image has 8035 counts for 0.5293 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300170h.evt
Total Good Bad: Region Time Phase Cut
15430 7362 89 0 0 7979
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15430 7362 89 0 0 7979
in 15180.54 seconds
Image has 7362 counts for 0.4850 counts/sec
Command not found; type ? for a command listing
!ad84041000g300170h:ASCA >
!ad84041000g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad84041000g300170h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!ad84041000g300170h:ASCA > read events ad84041000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!ad84041000g300170h:ASCA-GIS3-PH > set image sky
!ad84041000g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad84041000g300170h:ASCA-GIS3-PH > extract image
!ad84041000g300170h:ASCA-GIS3-PH > save image outfile=ad84041000g300170h.img
Wrote image to file ad84041000g300170h.img
!ad84041000g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad84041000g300170h:ASCA-GIS3-PH > extract image
!ad84041000g300170h:ASCA-GIS3-PH > save image outfile=ad84041000g300170h_lo.img
Wrote image to file ad84041000g300170h_lo.img
!ad84041000g300170h:ASCA-GIS3-PH > clear pha_cut
!ad84041000g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad84041000g300170h:ASCA-GIS3-PH > extract image
!ad84041000g300170h:ASCA-GIS3-PH > save image outfile=ad84041000g300170h_hi.img
Wrote image to file ad84041000g300170h_hi.img
!ad84041000g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad84041000g300270m.expo
ASCAEXPO_V0.9b
reading data file: ad84041000g300270m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960727_0447.1900
making an exposure map...
Aspect RA/DEC/ROLL : 203.2880 -31.6987 66.7168
Mean RA/DEC/ROLL : 203.2924 -31.7055 66.7168
Pnt RA/DEC/ROLL : 203.2794 -31.6885 66.7168
Image rebin factor : 1
Attitude Records : 51527
GTI intervals : 9
Total GTI (secs) : 4287.746
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 904.9969482 904.9969482
20 Percent Complete: Total/live time: 904.9969482 904.9969482
30 Percent Complete: Total/live time: 2332.0170898 2332.0170898
40 Percent Complete: Total/live time: 2332.0170898 2332.0170898
50 Percent Complete: Total/live time: 2345.0170898 2345.0170898
60 Percent Complete: Total/live time: 2680.1010742 2680.1010742
70 Percent Complete: Total/live time: 3508.2031250 3508.2031250
80 Percent Complete: Total/live time: 3508.2031250 3508.2031250
90 Percent Complete: Total/live time: 3908.9184570 3908.9184570
100 Percent Complete: Total/live time: 4287.7456055 4287.7456055
Number of attitude steps used: 23
Number of attitude steps avail: 10735
Mean RA/DEC pixel offset: 2.2142 -2.6857
writing expo file: ad84041000g300270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad84041000g300270m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad84041000g300270m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.43E+04 4310 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300270m.evt
Total Good Bad: Region Time Phase Cut
4310 4287 23 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4310 4287 23 0 0 0
in 4287.75 seconds
Image has 4287 counts for 0.9998 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300270m.evt
Total Good Bad: Region Time Phase Cut
4310 2267 23 0 0 2020
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4310 2267 23 0 0 2020
in 4287.75 seconds
Image has 2267 counts for 0.5287 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300270m.evt
Total Good Bad: Region Time Phase Cut
4310 2037 23 0 0 2250
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4310 2037 23 0 0 2250
in 4287.75 seconds
Image has 2037 counts for 0.4751 counts/sec
Command not found; type ? for a command listing
!ad84041000g300270m:ASCA >
!ad84041000g300270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad84041000g300270m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!ad84041000g300270m:ASCA > read events ad84041000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!ad84041000g300270m:ASCA-GIS3-PH > set image sky
!ad84041000g300270m:ASCA-GIS3-PH > filter region corner_point.reg
!ad84041000g300270m:ASCA-GIS3-PH > extract image
!ad84041000g300270m:ASCA-GIS3-PH > save image outfile=ad84041000g300270m.img
Wrote image to file ad84041000g300270m.img
!ad84041000g300270m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad84041000g300270m:ASCA-GIS3-PH > extract image
!ad84041000g300270m:ASCA-GIS3-PH > save image outfile=ad84041000g300270m_lo.img
Wrote image to file ad84041000g300270m_lo.img
!ad84041000g300270m:ASCA-GIS3-PH > clear pha_cut
!ad84041000g300270m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad84041000g300270m:ASCA-GIS3-PH > extract image
!ad84041000g300270m:ASCA-GIS3-PH > save image outfile=ad84041000g300270m_hi.img
Wrote image to file ad84041000g300270m_hi.img
!ad84041000g300270m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad84041000g300370h.expo
ASCAEXPO_V0.9b
reading data file: ad84041000g300370h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa960727_0447.1900
making an exposure map...
Aspect RA/DEC/ROLL : 203.2880 -31.6987 66.7176
Mean RA/DEC/ROLL : 203.2908 -31.7037 66.7176
Pnt RA/DEC/ROLL : 203.2845 -31.6955 66.7176
Image rebin factor : 1
Attitude Records : 51527
GTI intervals : 4
Total GTI (secs) : 565.998
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 565.9980469 565.9980469
100 Percent Complete: Total/live time: 565.9980469 565.9980469
Number of attitude steps used: 2
Number of attitude steps avail: 1142
Mean RA/DEC pixel offset: 0.8964 -1.0192
writing expo file: ad84041000g300370h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad84041000g300370h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad84041000g300370h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 549 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300370h.evt
Total Good Bad: Region Time Phase Cut
549 547 2 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
549 547 2 0 0 0
in 566.00 seconds
Image has 547 counts for 0.9664 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300370h.evt
Total Good Bad: Region Time Phase Cut
549 285 2 0 0 262
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
549 285 2 0 0 262
in 566.00 seconds
Image has 285 counts for 0.5035 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300370h.evt
Total Good Bad: Region Time Phase Cut
549 262 2 0 0 285
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
549 262 2 0 0 285
in 566.00 seconds
Image has 262 counts for 0.4629 counts/sec
Command not found; type ? for a command listing
!ad84041000g300370h:ASCA >
!ad84041000g300370h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad84041000g300370h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!ad84041000g300370h:ASCA > read events ad84041000g300370h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!ad84041000g300370h:ASCA-GIS3-PH > set image sky
!ad84041000g300370h:ASCA-GIS3-PH > filter region corner_point.reg
!ad84041000g300370h:ASCA-GIS3-PH > extract image
!ad84041000g300370h:ASCA-GIS3-PH > save image outfile=ad84041000g300370h.img
Wrote image to file ad84041000g300370h.img
!ad84041000g300370h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad84041000g300370h:ASCA-GIS3-PH > extract image
!ad84041000g300370h:ASCA-GIS3-PH > save image outfile=ad84041000g300370h_lo.img
Wrote image to file ad84041000g300370h_lo.img
!ad84041000g300370h:ASCA-GIS3-PH > clear pha_cut
!ad84041000g300370h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad84041000g300370h:ASCA-GIS3-PH > extract image
!ad84041000g300370h:ASCA-GIS3-PH > save image outfile=ad84041000g300370h_hi.img
Wrote image to file ad84041000g300370h_hi.img
!ad84041000g300370h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad84041000s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad84041000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa960727_0447.1900
making an exposure map...
Aspect RA/DEC/ROLL : 203.2880 -31.6987 66.7051
Mean RA/DEC/ROLL : 203.3142 -31.6994 66.7051
Pnt RA/DEC/ROLL : 203.3589 -31.7753 66.7051
Image rebin factor : 4
Attitude Records : 51527
Hot Pixels : 178
GTI intervals : 27
Total GTI (secs) : 10292.252
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1134.9808350 1134.9808350
20 Percent Complete: Total/live time: 3063.9768066 3063.9768066
30 Percent Complete: Total/live time: 4140.8857422 4140.8857422
40 Percent Complete: Total/live time: 4865.0068359 4865.0068359
50 Percent Complete: Total/live time: 6995.4755859 6995.4755859
60 Percent Complete: Total/live time: 6995.4755859 6995.4755859
70 Percent Complete: Total/live time: 8581.4384766 8581.4384766
80 Percent Complete: Total/live time: 8581.4384766 8581.4384766
90 Percent Complete: Total/live time: 10292.2509766 10292.2509766
100 Percent Complete: Total/live time: 10292.2509766 10292.2509766
Number of attitude steps used: 34
Number of attitude steps avail: 23370
Mean RA/DEC pixel offset: -31.1674 -101.5391
writing expo file: ad84041000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad84041000s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad84041000s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:57:51 0.10E+05 7833 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000102h.evt
Total Good Bad: Region Time Phase Cut
7833 7833 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7833 7833 0 0 0 0
in 10292.25 seconds
Image has 7833 counts for 0.7611 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000102h.evt
Total Good Bad: Region Time Phase Cut
7833 5095 0 0 0 2738
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7833 5095 0 0 0 2738
in 10292.25 seconds
Image has 5095 counts for 0.4950 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000102h.evt
Total Good Bad: Region Time Phase Cut
7833 2745 0 0 0 5088
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7833 2745 0 0 0 5088
in 10292.25 seconds
Image has 2745 counts for 0.2667 counts/sec
Command not found; type ? for a command listing
!ad84041000s000102h:ASCA >
!ad84041000s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad84041000s000102h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!ad84041000s000102h:ASCA > read events ad84041000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!ad84041000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad84041000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad84041000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad84041000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad84041000s000102h.img
Wrote image to file ad84041000s000102h.img
!ad84041000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad84041000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad84041000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad84041000s000102h_lo.img
Wrote image to file ad84041000s000102h_lo.img
!ad84041000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad84041000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad84041000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad84041000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad84041000s000102h_hi.img
Wrote image to file ad84041000s000102h_hi.img
!ad84041000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad84041000s000202h.expo
ASCAEXPO_V0.9b
reading data file: ad84041000s000202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa960727_0447.1900
making an exposure map...
Aspect RA/DEC/ROLL : 203.2880 -31.6987 66.7047
Mean RA/DEC/ROLL : 203.3146 -31.6990 66.7047
Pnt RA/DEC/ROLL : 203.2600 -31.7002 66.7047
Image rebin factor : 4
Attitude Records : 51527
Hot Pixels : 165
GTI intervals : 17
Total GTI (secs) : 4617.661
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1917.9687500 1917.9687500
20 Percent Complete: Total/live time: 1917.9687500 1917.9687500
30 Percent Complete: Total/live time: 1918.3157959 1918.3157959
40 Percent Complete: Total/live time: 1918.3157959 1918.3157959
50 Percent Complete: Total/live time: 3478.9980469 3478.9980469
60 Percent Complete: Total/live time: 3478.9980469 3478.9980469
70 Percent Complete: Total/live time: 3828.4968262 3828.4968262
80 Percent Complete: Total/live time: 3828.4968262 3828.4968262
90 Percent Complete: Total/live time: 4317.4863281 4317.4863281
100 Percent Complete: Total/live time: 4617.6606445 4617.6606445
Number of attitude steps used: 8
Number of attitude steps avail: 10999
Mean RA/DEC pixel offset: -33.7113 -82.4930
writing expo file: ad84041000s000202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad84041000s000202h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad84041000s000202h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 14:43:39 0.46E+04 3618 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000202h.evt
Total Good Bad: Region Time Phase Cut
3618 3618 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3618 3618 0 0 0 0
in 4617.66 seconds
Image has 3618 counts for 0.7835 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000202h.evt
Total Good Bad: Region Time Phase Cut
3618 2315 0 0 0 1303
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3618 2315 0 0 0 1303
in 4617.66 seconds
Image has 2315 counts for 0.5013 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000202h.evt
Total Good Bad: Region Time Phase Cut
3618 1310 0 0 0 2308
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3618 1310 0 0 0 2308
in 4617.66 seconds
Image has 1310 counts for 0.2837 counts/sec
Command not found; type ? for a command listing
!ad84041000s000202h:ASCA >
!ad84041000s000202h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad84041000s000202h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!ad84041000s000202h:ASCA > read events ad84041000s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!ad84041000s000202h:ASCA-SIS0-BRIGHT > set image sky
!ad84041000s000202h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad84041000s000202h:ASCA-SIS0-BRIGHT > extract image
!ad84041000s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad84041000s000202h.img
Wrote image to file ad84041000s000202h.img
!ad84041000s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad84041000s000202h:ASCA-SIS0-BRIGHT > extract image
!ad84041000s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad84041000s000202h_lo.img
Wrote image to file ad84041000s000202h_lo.img
!ad84041000s000202h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad84041000s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad84041000s000202h:ASCA-SIS0-BRIGHT > extract image
!ad84041000s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad84041000s000202h_hi.img
Wrote image to file ad84041000s000202h_hi.img
!ad84041000s000202h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad84041000s000302m.expo
ASCAEXPO_V0.9b
reading data file: ad84041000s000302m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa960727_0447.1900
making an exposure map...
Aspect RA/DEC/ROLL : 203.2880 -31.6987 66.7042
Mean RA/DEC/ROLL : 203.3155 -31.7004 66.7042
Pnt RA/DEC/ROLL : 203.2558 -31.6935 66.7042
Image rebin factor : 4
Attitude Records : 51527
Hot Pixels : 35
GTI intervals : 2
Total GTI (secs) : 51.285
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 25.6521358 25.6521358
20 Percent Complete: Total/live time: 25.6521358 25.6521358
30 Percent Complete: Total/live time: 51.2845154 51.2845154
100 Percent Complete: Total/live time: 51.2845154 51.2845154
Number of attitude steps used: 3
Number of attitude steps avail: 2942
Mean RA/DEC pixel offset: -27.1181 -65.1569
writing expo file: ad84041000s000302m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad84041000s000302m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad84041000s000302m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT MEDIUM 27/07/96 06:24:59 0.51E+02 83 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000302m.evt
Total Good Bad: Region Time Phase Cut
83 83 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
83 83 0 0 0 0
in 51.28 seconds
Image has 83 counts for 1.618 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000302m.evt
Total Good Bad: Region Time Phase Cut
83 68 0 0 0 15
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
83 68 0 0 0 15
in 51.28 seconds
Image has 68 counts for 1.326 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000302m.evt
Total Good Bad: Region Time Phase Cut
83 15 0 0 0 68
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
83 15 0 0 0 68
in 51.28 seconds
Image has 15 counts for 0.2925 counts/sec
Command not found; type ? for a command listing
!ad84041000s000302m:ASCA >
!ad84041000s000302m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad84041000s000302m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!ad84041000s000302m:ASCA > read events ad84041000s000302m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!ad84041000s000302m:ASCA-SIS0-BRIGHT > set image sky
!ad84041000s000302m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad84041000s000302m:ASCA-SIS0-BRIGHT > extract image
!ad84041000s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad84041000s000302m.img
Wrote image to file ad84041000s000302m.img
!ad84041000s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad84041000s000302m:ASCA-SIS0-BRIGHT > extract image
!ad84041000s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad84041000s000302m_lo.img
Wrote image to file ad84041000s000302m_lo.img
!ad84041000s000302m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad84041000s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad84041000s000302m:ASCA-SIS0-BRIGHT > extract image
!ad84041000s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad84041000s000302m_hi.img
Wrote image to file ad84041000s000302m_hi.img
!ad84041000s000302m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad84041000s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad84041000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa960727_0447.1900
making an exposure map...
Aspect RA/DEC/ROLL : 203.2880 -31.6987 66.7126
Mean RA/DEC/ROLL : 203.2986 -31.6929 66.7126
Pnt RA/DEC/ROLL : 203.2791 -31.7077 66.7126
Image rebin factor : 4
Attitude Records : 51527
Hot Pixels : 202
GTI intervals : 35
Total GTI (secs) : 14161.826
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1600.0000000 1600.0000000
20 Percent Complete: Total/live time: 3095.9379883 3095.9379883
30 Percent Complete: Total/live time: 4445.9072266 4445.9072266
40 Percent Complete: Total/live time: 6224.6997070 6224.6997070
50 Percent Complete: Total/live time: 7807.1630859 7807.1630859
60 Percent Complete: Total/live time: 11499.9453125 11499.9453125
70 Percent Complete: Total/live time: 11499.9453125 11499.9453125
80 Percent Complete: Total/live time: 11500.2919922 11500.2919922
90 Percent Complete: Total/live time: 13055.1630859 13055.1630859
100 Percent Complete: Total/live time: 14161.8261719 14161.8261719
Number of attitude steps used: 39
Number of attitude steps avail: 35038
Mean RA/DEC pixel offset: -36.5588 -30.3676
writing expo file: ad84041000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad84041000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad84041000s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 05:25:19 0.14E+05 9162 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100102h.evt
Total Good Bad: Region Time Phase Cut
9162 9162 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9162 9162 0 0 0 0
in 14161.83 seconds
Image has 9162 counts for 0.6470 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100102h.evt
Total Good Bad: Region Time Phase Cut
9162 5867 0 0 0 3295
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9162 5867 0 0 0 3295
in 14161.83 seconds
Image has 5867 counts for 0.4143 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100102h.evt
Total Good Bad: Region Time Phase Cut
9162 3303 0 0 0 5859
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9162 3303 0 0 0 5859
in 14161.83 seconds
Image has 3303 counts for 0.2332 counts/sec
Command not found; type ? for a command listing
!ad84041000s100102h:ASCA >
!ad84041000s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad84041000s100102h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!ad84041000s100102h:ASCA > read events ad84041000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!ad84041000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad84041000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad84041000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad84041000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad84041000s100102h.img
Wrote image to file ad84041000s100102h.img
!ad84041000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad84041000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad84041000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad84041000s100102h_lo.img
Wrote image to file ad84041000s100102h_lo.img
!ad84041000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad84041000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad84041000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad84041000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad84041000s100102h_hi.img
Wrote image to file ad84041000s100102h_hi.img
!ad84041000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad84041000s100202m.expo
ASCAEXPO_V0.9b
reading data file: ad84041000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa960727_0447.1900
making an exposure map...
Aspect RA/DEC/ROLL : 203.2880 -31.6987 66.7132
Mean RA/DEC/ROLL : 203.2982 -31.6925 66.7132
Pnt RA/DEC/ROLL : 203.2725 -31.7007 66.7132
Image rebin factor : 4
Attitude Records : 51527
Hot Pixels : 73
GTI intervals : 10
Total GTI (secs) : 3388.996
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1056.0000000 1056.0000000
20 Percent Complete: Total/live time: 1056.0000000 1056.0000000
30 Percent Complete: Total/live time: 1056.9653320 1056.9653320
40 Percent Complete: Total/live time: 1616.9630127 1616.9630127
50 Percent Complete: Total/live time: 2153.7111816 2153.7111816
60 Percent Complete: Total/live time: 2153.7111816 2153.7111816
70 Percent Complete: Total/live time: 2755.3632812 2755.3632812
80 Percent Complete: Total/live time: 2755.3632812 2755.3632812
90 Percent Complete: Total/live time: 3171.3632812 3171.3632812
100 Percent Complete: Total/live time: 3388.9956055 3388.9956055
Number of attitude steps used: 16
Number of attitude steps avail: 4142
Mean RA/DEC pixel offset: -36.1087 -27.6761
writing expo file: ad84041000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad84041000s100202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad84041000s100202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT MEDIUM 27/07/96 06:24:59 0.34E+04 2048 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100202m.evt
Total Good Bad: Region Time Phase Cut
2048 2048 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2048 2048 0 0 0 0
in 3389.00 seconds
Image has 2048 counts for 0.6043 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100202m.evt
Total Good Bad: Region Time Phase Cut
2048 1317 0 0 0 731
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2048 1317 0 0 0 731
in 3389.00 seconds
Image has 1317 counts for 0.3886 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100202m.evt
Total Good Bad: Region Time Phase Cut
2048 733 0 0 0 1315
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2048 733 0 0 0 1315
in 3389.00 seconds
Image has 733 counts for 0.2163 counts/sec
Command not found; type ? for a command listing
!ad84041000s100202m:ASCA >
!ad84041000s100202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad84041000s100202m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!ad84041000s100202m:ASCA > read events ad84041000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!ad84041000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad84041000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad84041000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad84041000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad84041000s100202m.img
Wrote image to file ad84041000s100202m.img
!ad84041000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad84041000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad84041000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad84041000s100202m_lo.img
Wrote image to file ad84041000s100202m_lo.img
!ad84041000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad84041000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad84041000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad84041000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad84041000s100202m_hi.img
Wrote image to file ad84041000s100202m_hi.img
!ad84041000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad84041000s100302h.expo
ASCAEXPO_V0.9b
reading data file: ad84041000s100302h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa960727_0447.1900
making an exposure map...
Aspect RA/DEC/ROLL : 203.2880 -31.6987 66.7134
Mean RA/DEC/ROLL : 203.2879 -31.6849 66.7134
Pnt RA/DEC/ROLL : 203.3756 -31.7825 66.7134
Image rebin factor : 4
Attitude Records : 51527
Hot Pixels : 149
GTI intervals : 3
Total GTI (secs) : 880.063
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 512.4996338 512.4996338
20 Percent Complete: Total/live time: 512.4996338 512.4996338
30 Percent Complete: Total/live time: 533.4996338 533.4996338
40 Percent Complete: Total/live time: 533.4996338 533.4996338
50 Percent Complete: Total/live time: 880.0627441 880.0627441
100 Percent Complete: Total/live time: 880.0627441 880.0627441
Number of attitude steps used: 4
Number of attitude steps avail: 2197
Mean RA/DEC pixel offset: -28.6938 -20.4434
writing expo file: ad84041000s100302h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad84041000s100302h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad84041000s100302h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:58:27 0.88E+03 602 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100302h.evt
Total Good Bad: Region Time Phase Cut
602 602 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
602 602 0 0 0 0
in 880.06 seconds
Image has 602 counts for 0.6840 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100302h.evt
Total Good Bad: Region Time Phase Cut
602 394 0 0 0 208
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
602 394 0 0 0 208
in 880.06 seconds
Image has 394 counts for 0.4477 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100302h.evt
Total Good Bad: Region Time Phase Cut
602 208 0 0 0 394
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
602 208 0 0 0 394
in 880.06 seconds
Image has 208 counts for 0.2363 counts/sec
Command not found; type ? for a command listing
!ad84041000s100302h:ASCA >
!ad84041000s100302h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad84041000s100302h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!ad84041000s100302h:ASCA > read events ad84041000s100302h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!ad84041000s100302h:ASCA-SIS1-BRIGHT > set image sky
!ad84041000s100302h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad84041000s100302h:ASCA-SIS1-BRIGHT > extract image
!ad84041000s100302h:ASCA-SIS1-BRIGHT > save image outfile=ad84041000s100302h.img
Wrote image to file ad84041000s100302h.img
!ad84041000s100302h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad84041000s100302h:ASCA-SIS1-BRIGHT > extract image
!ad84041000s100302h:ASCA-SIS1-BRIGHT > save image outfile=ad84041000s100302h_lo.img
Wrote image to file ad84041000s100302h_lo.img
!ad84041000s100302h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad84041000s100302h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad84041000s100302h:ASCA-SIS1-BRIGHT > extract image
!ad84041000s100302h:ASCA-SIS1-BRIGHT > save image outfile=ad84041000s100302h_hi.img
Wrote image to file ad84041000s100302h_hi.img
!ad84041000s100302h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad84041000s000102h.expo ad84041000s000202h.expo ad84041000s000302m.expo ad84041000s100102h.expo ad84041000s100202m.expo ad84041000s100302h.expo-> Summing the following images to produce ad84041000sis32002_all.totsky
ad84041000s000102h.img ad84041000s000202h.img ad84041000s000302m.img ad84041000s100102h.img ad84041000s100202m.img ad84041000s100302h.img-> Summing the following images to produce ad84041000sis32002_lo.totsky
ad84041000s000102h_lo.img ad84041000s000202h_lo.img ad84041000s000302m_lo.img ad84041000s100102h_lo.img ad84041000s100202m_lo.img ad84041000s100302h_lo.img-> Summing the following images to produce ad84041000sis32002_hi.totsky
ad84041000s000102h_hi.img ad84041000s000202h_hi.img ad84041000s000302m_hi.img ad84041000s100102h_hi.img ad84041000s100202m_hi.img ad84041000s100302h_hi.img-> Running XIMAGE to create ad84041000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad84041000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 11.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 11 min: 0 ![2]XIMAGE> read/exp_map ad84041000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 556.535 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 556 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 17234 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 15.0000 15 0 ![9]XIMAGE> exit-> Summing gis images
ad84041000g200170h.expo ad84041000g200270m.expo ad84041000g200370h.expo ad84041000g300170h.expo ad84041000g300270m.expo ad84041000g300370h.expo-> Summing the following images to produce ad84041000gis25670_all.totsky
ad84041000g200170h.img ad84041000g200270m.img ad84041000g200370h.img ad84041000g300170h.img ad84041000g300270m.img ad84041000g300370h.img-> Summing the following images to produce ad84041000gis25670_lo.totsky
ad84041000g200170h_lo.img ad84041000g200270m_lo.img ad84041000g200370h_lo.img ad84041000g300170h_lo.img ad84041000g300270m_lo.img ad84041000g300370h_lo.img-> Summing the following images to produce ad84041000gis25670_hi.totsky
ad84041000g200170h_hi.img ad84041000g200270m_hi.img ad84041000g200370h_hi.img ad84041000g300170h_hi.img ad84041000g300270m_hi.img ad84041000g300370h_hi.img-> Running XIMAGE to create ad84041000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad84041000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 37.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 37 min: 0 ![2]XIMAGE> read/exp_map ad84041000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 667.909 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 667 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 166 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 16.0000 16 0 ![9]XIMAGE> exit
106 134 0.000615519 115 20 32.3803-> Smoothing ad84041000gis25670_hi.totsky with ad84041000gis25670.totexpo
106 133 0.000280034 114 21 28.3298-> Smoothing ad84041000gis25670_lo.totsky with ad84041000gis25670.totexpo
106 134 0.000346576 115 19 37.4799-> Determining extraction radii
106 134 24 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad84041000gis25670.src
105 177 0.000202976 175 43 34.2249-> Smoothing ad84041000sis32002_hi.totsky with ad84041000sis32002.totexpo
109 170 6.95338e-05 177 45 22.0364-> Smoothing ad84041000sis32002_lo.totsky with ad84041000sis32002.totexpo
106 176 0.000130633 175 43 39.9803-> Determining extraction radii
105 177 43 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad84041000sis32002.src
The sum of the selected column is 1419.0000 The mean of the selected column is 473.00000 The standard deviation of the selected column is 1.0000000 The minimum of selected column is 472.00000 The maximum of selected column is 474.00000 The number of points used in calculation is 3-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1246.0000 The mean of the selected column is 415.33333 The standard deviation of the selected column is 2.5166115 The minimum of selected column is 413.00000 The maximum of selected column is 418.00000 The number of points used in calculation is 3-> Converting (420.0,708.0,2.0) to s1 detector coordinates
The sum of the selected column is 1415.0000 The mean of the selected column is 471.66667 The standard deviation of the selected column is 3.0550505 The minimum of selected column is 469.00000 The maximum of selected column is 475.00000 The number of points used in calculation is 3-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1348.0000 The mean of the selected column is 449.33333 The standard deviation of the selected column is 4.7258156 The minimum of selected column is 444.00000 The maximum of selected column is 453.00000 The number of points used in calculation is 3-> Converting (106.0,134.0,2.0) to g2 detector coordinates
The sum of the selected column is 17115.000 The mean of the selected column is 110.41935 The standard deviation of the selected column is 1.1502172 The minimum of selected column is 108.00000 The maximum of selected column is 113.00000 The number of points used in calculation is 155-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 16694.000 The mean of the selected column is 107.70323 The standard deviation of the selected column is 1.2901938 The minimum of selected column is 105.00000 The maximum of selected column is 110.00000 The number of points used in calculation is 155-> Converting (106.0,134.0,2.0) to g3 detector coordinates
The sum of the selected column is 20259.000 The mean of the selected column is 116.43103 The standard deviation of the selected column is 1.1446594 The minimum of selected column is 114.00000 The maximum of selected column is 119.00000 The number of points used in calculation is 174-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 18864.000 The mean of the selected column is 108.41379 The standard deviation of the selected column is 1.1977988 The minimum of selected column is 105.00000 The maximum of selected column is 111.00000 The number of points used in calculation is 174
1 ad84041000s000102h.evt 11451 1 ad84041000s000202h.evt 11451 2 ad84041000s000302m.evt 83-> Fetching SIS0_NOTCHIP2.1
ad84041000s000102h.evt ad84041000s000202h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:57:51 0.10E+05 7833 1100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:57:51 0.10E+05 7833 1100
2 P1_[NEAR BRIGHT HIGH 27/07/96 14:43:39 0.46E+04 3618 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000102h.evt
Total Good Bad: Region Time Phase Cut
7833 5195 2638 0 0 0
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000202h.evt
Total Good Bad: Region Time Phase Cut
3618 2398 1220 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11451 7593 3858 0 0 0
in 14909.91 seconds
Spectrum has 7593 counts for 0.5093 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 14910. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.75977E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad84041000s010102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000102h.evt
Total Good Bad: Region Time Phase Cut
7833 5195 2638 0 0 0
Writing events file
5195 events written to the output file
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000202h.evt
Total Good Bad: Region Time Phase Cut
3618 2398 1220 0 0 0
Writing events file
7593 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11451 7593 3858 0 0 0
in 14909.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad84041000s000202h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad84041000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad84041000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad84041000s010102_1.pi group=yes
Wrote spectrum to ad84041000s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad84041000s010102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 14910. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 5.75977E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 21 are grouped by a factor 2 ... 22 - 23 are single channels ... 24 - 25 are grouped by a factor 2 ... 26 - 71 are single channels ... 72 - 73 are grouped by a factor 2 ... 74 - 79 are single channels ... 80 - 103 are grouped by a factor 2 ... 104 - 106 are grouped by a factor 3 ... 107 - 114 are grouped by a factor 2 ... 115 - 120 are grouped by a factor 3 ... 121 - 122 are grouped by a factor 2 ... 123 - 137 are grouped by a factor 3 ... 138 - 141 are grouped by a factor 4 ... 142 - 144 are grouped by a factor 3 ... 145 - 152 are grouped by a factor 4 ... 153 - 157 are grouped by a factor 5 ... 158 - 163 are grouped by a factor 6 ... 164 - 168 are grouped by a factor 5 ... 169 - 174 are grouped by a factor 6 ... 175 - 181 are grouped by a factor 7 ... 182 - 190 are grouped by a factor 9 ... 191 - 202 are grouped by a factor 12 ... 203 - 216 are grouped by a factor 14 ... 217 - 225 are grouped by a factor 9 ... 226 - 256 are grouped by a factor 31 ... 257 - 295 are grouped by a factor 39 ... 296 - 481 are grouped by a factor 186 ... 482 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad84041000s010102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad84041000s010102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 43 by 44 bins
expanded to 43 by 44 bins
First WMAP bin is at detector pixel 304 248
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 66.370 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 7.53100E+03
Weighted mean angle from optical axis = 6.111 arcmin
-> Standard Output From STOOL group_event_files:1 ad84041000s000112h.evt 11710 1 ad84041000s000212h.evt 11710 2 ad84041000s000312m.evt 83-> SIS0_NOTCHIP2.1 already present in current directory
ad84041000s000112h.evt ad84041000s000212h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 04:57:51 0.10E+05 8006 1100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 04:57:51 0.10E+05 8006 1100
2 P1_[NEAR BRIGHT2 HIGH 27/07/96 14:43:39 0.46E+04 3704 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000112h.evt
Total Good Bad: Region Time Phase Cut
8006 5287 2719 0 0 0
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000212h.evt
Total Good Bad: Region Time Phase Cut
3704 2430 1274 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11710 7717 3993 0 0 0
in 14909.91 seconds
Spectrum has 7717 counts for 0.5176 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 14910. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.75977E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad84041000s010212_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000112h.evt
Total Good Bad: Region Time Phase Cut
8006 5287 2719 0 0 0
Writing events file
5287 events written to the output file
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000212h.evt
Total Good Bad: Region Time Phase Cut
3704 2430 1274 0 0 0
Writing events file
7717 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11710 7717 3993 0 0 0
in 14909.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT2 > read events ad84041000s000212h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad84041000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad84041000s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad84041000s010212_1.pi group=yes
Wrote spectrum to ad84041000s010212_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad84041000s010212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 14910. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 5.75977E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 43 are grouped by a factor 3 ... 44 - 57 are grouped by a factor 2 ... 58 - 59 are single channels ... 60 - 61 are grouped by a factor 2 ... 62 - 114 are single channels ... 115 - 116 are grouped by a factor 2 ... 117 - 119 are single channels ... 120 - 121 are grouped by a factor 2 ... 122 - 122 are single channels ... 123 - 128 are grouped by a factor 2 ... 129 - 129 are single channels ... 130 - 149 are grouped by a factor 2 ... 150 - 152 are grouped by a factor 3 ... 153 - 158 are grouped by a factor 2 ... 159 - 179 are grouped by a factor 3 ... 180 - 187 are grouped by a factor 4 ... 188 - 199 are grouped by a factor 3 ... 200 - 204 are grouped by a factor 5 ... 205 - 224 are grouped by a factor 4 ... 225 - 239 are grouped by a factor 5 ... 240 - 247 are grouped by a factor 4 ... 248 - 265 are grouped by a factor 6 ... 266 - 270 are grouped by a factor 5 ... 271 - 276 are grouped by a factor 6 ... 277 - 304 are grouped by a factor 7 ... 305 - 313 are grouped by a factor 9 ... 314 - 323 are grouped by a factor 10 ... 324 - 332 are grouped by a factor 9 ... 333 - 340 are grouped by a factor 8 ... 341 - 351 are grouped by a factor 11 ... 352 - 387 are grouped by a factor 18 ... 388 - 435 are grouped by a factor 24 ... 436 - 453 are grouped by a factor 18 ... 454 - 569 are grouped by a factor 58 ... 570 - 723 are grouped by a factor 154 ... 724 - 1011 are grouped by a factor 288 ... 1012 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad84041000s010212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad84041000s010212_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 43 by 44 bins
expanded to 43 by 44 bins
First WMAP bin is at detector pixel 304 248
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 66.370 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 7.65100E+03
Weighted mean angle from optical axis = 6.117 arcmin
-> Standard Output From STOOL group_event_files:1 ad84041000s100102h.evt 9764 1 ad84041000s100302h.evt 9764 2 ad84041000s100202m.evt 2048-> Fetching SIS1_NOTCHIP0.1
ad84041000s100102h.evt ad84041000s100302h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 05:25:19 0.14E+05 9162 0011
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 05:25:19 0.14E+05 9162 0011
2 P1_[NEAR BRIGHT HIGH 27/07/96 04:58:27 0.88E+03 602 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100102h.evt
Total Good Bad: Region Time Phase Cut
9162 5345 3817 0 0 0
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100302h.evt
Total Good Bad: Region Time Phase Cut
602 344 258 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9764 5689 4075 0 0 0
in 15041.89 seconds
Spectrum has 5689 counts for 0.3782 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 15042. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.77539E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad84041000s110102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100102h.evt
Total Good Bad: Region Time Phase Cut
9162 5345 3817 0 0 0
Writing events file
5345 events written to the output file
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100302h.evt
Total Good Bad: Region Time Phase Cut
602 344 258 0 0 0
Writing events file
5689 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9764 5689 4075 0 0 0
in 15041.89 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad84041000s100302h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad84041000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad84041000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad84041000s110102_1.pi group=yes
Wrote spectrum to ad84041000s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad84041000s110102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 15042. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 5.77539E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 18 are grouped by a factor 3 ... 19 - 24 are grouped by a factor 2 ... 25 - 63 are single channels ... 64 - 67 are grouped by a factor 2 ... 68 - 68 are single channels ... 69 - 72 are grouped by a factor 2 ... 73 - 73 are single channels ... 74 - 87 are grouped by a factor 2 ... 88 - 90 are grouped by a factor 3 ... 91 - 92 are grouped by a factor 2 ... 93 - 95 are grouped by a factor 3 ... 96 - 99 are grouped by a factor 2 ... 100 - 120 are grouped by a factor 3 ... 121 - 124 are grouped by a factor 4 ... 125 - 127 are grouped by a factor 3 ... 128 - 132 are grouped by a factor 5 ... 133 - 140 are grouped by a factor 4 ... 141 - 150 are grouped by a factor 5 ... 151 - 156 are grouped by a factor 6 ... 157 - 161 are grouped by a factor 5 ... 162 - 175 are grouped by a factor 7 ... 176 - 183 are grouped by a factor 8 ... 184 - 195 are grouped by a factor 12 ... 196 - 209 are grouped by a factor 14 ... 210 - 225 are grouped by a factor 16 ... 226 - 257 are grouped by a factor 32 ... 258 - 352 are grouped by a factor 95 ... 353 - 457 are grouped by a factor 105 ... 458 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad84041000s110102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad84041000s110102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 43 by 44 bins
expanded to 43 by 44 bins
First WMAP bin is at detector pixel 304 280
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 66.550 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.63700E+03
Weighted mean angle from optical axis = 9.060 arcmin
-> SIS1_NOTCHIP0.1 already present in current directoryad84041000s100202m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT MEDIUM 27/07/96 06:24:59 0.34E+04 2048 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100202m.evt
Total Good Bad: Region Time Phase Cut
2048 1215 833 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2048 1215 833 0 0 0
in 3389.00 seconds
Spectrum has 1215 counts for 0.3585 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3389.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.77539E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad84041000s110202_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100202m.evt
Total Good Bad: Region Time Phase Cut
2048 1215 833 0 0 0
Writing events file
1215 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2048 1215 833 0 0 0
in 3389.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad84041000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad84041000s110202.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad84041000s110202_1.pi group=yes
Wrote spectrum to ad84041000s110202_1.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad84041000s110202_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 3389.0 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 5.77539E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 26 are grouped by a factor 11 ... 27 - 30 are grouped by a factor 4 ... 31 - 36 are grouped by a factor 2 ... 37 - 39 are grouped by a factor 3 ... 40 - 53 are grouped by a factor 2 ... 54 - 56 are grouped by a factor 3 ... 57 - 72 are grouped by a factor 4 ... 73 - 77 are grouped by a factor 5 ... 78 - 86 are grouped by a factor 9 ... 87 - 96 are grouped by a factor 10 ... 97 - 108 are grouped by a factor 12 ... 109 - 122 are grouped by a factor 14 ... 123 - 135 are grouped by a factor 13 ... 136 - 163 are grouped by a factor 28 ... 164 - 220 are grouped by a factor 57 ... 221 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad84041000s110202_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad84041000s110202_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 43 by 44 bins
expanded to 43 by 44 bins
First WMAP bin is at detector pixel 304 280
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 66.550 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.18500E+03
Weighted mean angle from optical axis = 9.197 arcmin
-> Standard Output From STOOL group_event_files:1 ad84041000s100112h.evt 10000 1 ad84041000s100312h.evt 10000 2 ad84041000s100212m.evt 2076-> SIS1_NOTCHIP0.1 already present in current directory
ad84041000s100112h.evt ad84041000s100312h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 05:25:19 0.14E+05 9383 0011
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 05:25:19 0.14E+05 9383 0011
2 P1_[NEAR BRIGHT2 HIGH 27/07/96 04:58:27 0.88E+03 617 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100112h.evt
Total Good Bad: Region Time Phase Cut
9383 5434 3949 0 0 0
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100312h.evt
Total Good Bad: Region Time Phase Cut
617 349 268 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10000 5783 4217 0 0 0
in 15041.89 seconds
Spectrum has 5783 counts for 0.3845 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 15042. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.77539E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad84041000s110312_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100112h.evt
Total Good Bad: Region Time Phase Cut
9383 5434 3949 0 0 0
Writing events file
5434 events written to the output file
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100312h.evt
Total Good Bad: Region Time Phase Cut
617 349 268 0 0 0
Writing events file
5783 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10000 5783 4217 0 0 0
in 15041.89 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT2 > read events ad84041000s100312h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad84041000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad84041000s110312.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad84041000s110312_1.pi group=yes
Wrote spectrum to ad84041000s110312_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad84041000s110312_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 15042. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 5.77539E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 37 are grouped by a factor 5 ... 38 - 45 are grouped by a factor 4 ... 46 - 48 are grouped by a factor 3 ... 49 - 58 are grouped by a factor 2 ... 59 - 60 are single channels ... 61 - 66 are grouped by a factor 2 ... 67 - 105 are single channels ... 106 - 107 are grouped by a factor 2 ... 108 - 110 are single channels ... 111 - 112 are grouped by a factor 2 ... 113 - 114 are single channels ... 115 - 116 are grouped by a factor 2 ... 117 - 119 are single channels ... 120 - 133 are grouped by a factor 2 ... 134 - 139 are grouped by a factor 3 ... 140 - 141 are grouped by a factor 2 ... 142 - 144 are grouped by a factor 3 ... 145 - 146 are grouped by a factor 2 ... 147 - 152 are grouped by a factor 3 ... 153 - 156 are grouped by a factor 4 ... 157 - 161 are grouped by a factor 5 ... 162 - 169 are grouped by a factor 4 ... 170 - 175 are grouped by a factor 3 ... 176 - 180 are grouped by a factor 5 ... 181 - 184 are grouped by a factor 4 ... 185 - 194 are grouped by a factor 5 ... 195 - 202 are grouped by a factor 4 ... 203 - 207 are grouped by a factor 5 ... 208 - 213 are grouped by a factor 6 ... 214 - 223 are grouped by a factor 5 ... 224 - 235 are grouped by a factor 6 ... 236 - 240 are grouped by a factor 5 ... 241 - 247 are grouped by a factor 7 ... 248 - 252 are grouped by a factor 5 ... 253 - 260 are grouped by a factor 8 ... 261 - 267 are grouped by a factor 7 ... 268 - 283 are grouped by a factor 8 ... 284 - 293 are grouped by a factor 10 ... 294 - 304 are grouped by a factor 11 ... 305 - 324 are grouped by a factor 10 ... 325 - 352 are grouped by a factor 14 ... 353 - 368 are grouped by a factor 16 ... 369 - 390 are grouped by a factor 22 ... 391 - 418 are grouped by a factor 28 ... 419 - 444 are grouped by a factor 26 ... 445 - 509 are grouped by a factor 65 ... 510 - 674 are grouped by a factor 165 ... --------------------------------------------- ... ...... exiting, changes written to file : ad84041000s110312_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad84041000s110312_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 43 by 44 bins
expanded to 43 by 44 bins
First WMAP bin is at detector pixel 304 280
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 66.550 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.73100E+03
Weighted mean angle from optical axis = 9.054 arcmin
-> SIS1_NOTCHIP0.1 already present in current directoryad84041000s100212m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 MEDIUM 27/07/96 06:24:59 0.34E+04 2076 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100212m.evt
Total Good Bad: Region Time Phase Cut
2076 1234 842 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2076 1234 842 0 0 0
in 3389.00 seconds
Spectrum has 1234 counts for 0.3641 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 3389.0 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.77539E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad84041000s110412_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100212m.evt
Total Good Bad: Region Time Phase Cut
2076 1234 842 0 0 0
Writing events file
1234 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2076 1234 842 0 0 0
in 3389.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s100212m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad84041000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad84041000s110412.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad84041000s110412_1.pi group=yes
Wrote spectrum to ad84041000s110412_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad84041000s110412_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 3389.0 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 5.77539E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 51 are grouped by a factor 19 ... 52 - 58 are grouped by a factor 7 ... 59 - 68 are grouped by a factor 5 ... 69 - 84 are grouped by a factor 4 ... 85 - 87 are grouped by a factor 3 ... 88 - 99 are grouped by a factor 4 ... 100 - 109 are grouped by a factor 5 ... 110 - 113 are grouped by a factor 4 ... 114 - 127 are grouped by a factor 7 ... 128 - 133 are grouped by a factor 6 ... 134 - 140 are grouped by a factor 7 ... 141 - 148 are grouped by a factor 8 ... 149 - 182 are grouped by a factor 17 ... 183 - 202 are grouped by a factor 20 ... 203 - 226 are grouped by a factor 24 ... 227 - 252 are grouped by a factor 26 ... 253 - 284 are grouped by a factor 32 ... 285 - 350 are grouped by a factor 66 ... 351 - 501 are grouped by a factor 151 ... 502 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad84041000s110412_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Generating ad84041000s110412_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 43 by 44 bins
expanded to 43 by 44 bins
First WMAP bin is at detector pixel 304 280
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 66.550 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.20400E+03
Weighted mean angle from optical axis = 9.191 arcmin
-> Standard Output From STOOL group_event_files:1 ad84041000g200170h.evt 19181 1 ad84041000g200270m.evt 19181 1 ad84041000g200370h.evt 19181-> GIS2_REGION256.4 already present in current directory
ad84041000g200170h.evt ad84041000g200270m.evt ad84041000g200370h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 14508 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 14508 1024
2 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.43E+04 4093 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 14508 1024
2 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.43E+04 4093 1024
3 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 580 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200170h.evt
Total Good Bad: Region Time Phase Cut
14508 5226 9282 0 0 0
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200270m.evt
Total Good Bad: Region Time Phase Cut
4093 1394 2699 0 0 0
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200370h.evt
Total Good Bad: Region Time Phase Cut
580 186 394 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
19181 6806 12375 0 0 0
in 20040.29 seconds
Spectrum has 6806 counts for 0.3396 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 20040. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad84041000g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > read events ad84041000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > read events ad84041000g200370h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad84041000g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad84041000g210170_1.pi group=yes
Wrote spectrum to ad84041000g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad84041000g210170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad84041000g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 20040. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 29 are grouped by a factor 30 ... 30 - 37 are grouped by a factor 8 ... 38 - 44 are grouped by a factor 7 ... 45 - 52 are grouped by a factor 8 ... 53 - 58 are grouped by a factor 6 ... 59 - 70 are grouped by a factor 4 ... 71 - 76 are grouped by a factor 3 ... 77 - 96 are grouped by a factor 2 ... 97 - 97 are single channels ... 98 - 109 are grouped by a factor 2 ... 110 - 111 are single channels ... 112 - 117 are grouped by a factor 2 ... 118 - 118 are single channels ... 119 - 120 are grouped by a factor 2 ... 121 - 122 are single channels ... 123 - 130 are grouped by a factor 2 ... 131 - 132 are single channels ... 133 - 142 are grouped by a factor 2 ... 143 - 143 are single channels ... 144 - 155 are grouped by a factor 2 ... 156 - 156 are single channels ... 157 - 158 are grouped by a factor 2 ... 159 - 159 are single channels ... 160 - 185 are grouped by a factor 2 ... 186 - 188 are grouped by a factor 3 ... 189 - 190 are grouped by a factor 2 ... 191 - 205 are grouped by a factor 3 ... 206 - 213 are grouped by a factor 4 ... 214 - 225 are grouped by a factor 3 ... 226 - 257 are grouped by a factor 4 ... 258 - 262 are grouped by a factor 5 ... 263 - 270 are grouped by a factor 4 ... 271 - 285 are grouped by a factor 5 ... 286 - 289 are grouped by a factor 4 ... 290 - 295 are grouped by a factor 6 ... 296 - 299 are grouped by a factor 4 ... 300 - 309 are grouped by a factor 5 ... 310 - 315 are grouped by a factor 6 ... 316 - 320 are grouped by a factor 5 ... 321 - 332 are grouped by a factor 6 ... 333 - 339 are grouped by a factor 7 ... 340 - 347 are grouped by a factor 8 ... 348 - 352 are grouped by a factor 5 ... 353 - 360 are grouped by a factor 8 ... 361 - 367 are grouped by a factor 7 ... 368 - 375 are grouped by a factor 8 ... 376 - 385 are grouped by a factor 10 ... 386 - 394 are grouped by a factor 9 ... 395 - 401 are grouped by a factor 7 ... 402 - 409 are grouped by a factor 8 ... 410 - 418 are grouped by a factor 9 ... 419 - 448 are grouped by a factor 10 ... 449 - 459 are grouped by a factor 11 ... 460 - 474 are grouped by a factor 15 ... 475 - 493 are grouped by a factor 19 ... 494 - 506 are grouped by a factor 13 ... 507 - 523 are grouped by a factor 17 ... 524 - 535 are grouped by a factor 12 ... 536 - 548 are grouped by a factor 13 ... 549 - 565 are grouped by a factor 17 ... 566 - 606 are grouped by a factor 41 ... 607 - 642 are grouped by a factor 36 ... 643 - 699 are grouped by a factor 57 ... 700 - 827 are grouped by a factor 128 ... 828 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad84041000g210170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 48 46
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.80600E+03
Weighted mean angle from optical axis = 8.048 arcmin
-> Standard Output From STOOL group_event_files:1 ad84041000g300170h.evt 20289 1 ad84041000g300270m.evt 20289 1 ad84041000g300370h.evt 20289-> GIS3_REGION256.4 already present in current directory
ad84041000g300170h.evt ad84041000g300270m.evt ad84041000g300370h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 15430 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 15430 1024
2 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.43E+04 4310 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 15430 1024
2 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.43E+04 4310 1024
3 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 549 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300170h.evt
Total Good Bad: Region Time Phase Cut
15430 5918 9512 0 0 0
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300270m.evt
Total Good Bad: Region Time Phase Cut
4310 1619 2691 0 0 0
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300370h.evt
Total Good Bad: Region Time Phase Cut
549 216 333 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
20289 7753 12536 0 0 0
in 20034.29 seconds
Spectrum has 7753 counts for 0.3870 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 20034. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.90070E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad84041000g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > read events ad84041000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > read events ad84041000g300370h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad84041000g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad84041000g310170_1.pi group=yes
Wrote spectrum to ad84041000g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad84041000g310170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad84041000g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 20034. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.90070E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 27 are grouped by a factor 28 ... 28 - 36 are grouped by a factor 9 ... 37 - 50 are grouped by a factor 7 ... 51 - 56 are grouped by a factor 6 ... 57 - 61 are grouped by a factor 5 ... 62 - 69 are grouped by a factor 4 ... 70 - 72 are grouped by a factor 3 ... 73 - 98 are grouped by a factor 2 ... 99 - 99 are single channels ... 100 - 101 are grouped by a factor 2 ... 102 - 102 are single channels ... 103 - 106 are grouped by a factor 2 ... 107 - 108 are single channels ... 109 - 112 are grouped by a factor 2 ... 113 - 122 are single channels ... 123 - 124 are grouped by a factor 2 ... 125 - 126 are single channels ... 127 - 128 are grouped by a factor 2 ... 129 - 129 are single channels ... 130 - 131 are grouped by a factor 2 ... 132 - 132 are single channels ... 133 - 134 are grouped by a factor 2 ... 135 - 137 are single channels ... 138 - 139 are grouped by a factor 2 ... 140 - 140 are single channels ... 141 - 142 are grouped by a factor 2 ... 143 - 145 are single channels ... 146 - 149 are grouped by a factor 2 ... 150 - 151 are single channels ... 152 - 159 are grouped by a factor 2 ... 160 - 160 are single channels ... 161 - 162 are grouped by a factor 2 ... 163 - 163 are single channels ... 164 - 165 are grouped by a factor 2 ... 166 - 166 are single channels ... 167 - 192 are grouped by a factor 2 ... 193 - 207 are grouped by a factor 3 ... 208 - 209 are grouped by a factor 2 ... 210 - 215 are grouped by a factor 3 ... 216 - 219 are grouped by a factor 4 ... 220 - 222 are grouped by a factor 3 ... 223 - 226 are grouped by a factor 4 ... 227 - 229 are grouped by a factor 3 ... 230 - 237 are grouped by a factor 4 ... 238 - 249 are grouped by a factor 3 ... 250 - 253 are grouped by a factor 4 ... 254 - 259 are grouped by a factor 3 ... 260 - 275 are grouped by a factor 4 ... 276 - 285 are grouped by a factor 5 ... 286 - 291 are grouped by a factor 6 ... 292 - 321 are grouped by a factor 5 ... 322 - 327 are grouped by a factor 6 ... 328 - 331 are grouped by a factor 4 ... 332 - 349 are grouped by a factor 6 ... 350 - 363 are grouped by a factor 7 ... 364 - 371 are grouped by a factor 8 ... 372 - 377 are grouped by a factor 6 ... 378 - 391 are grouped by a factor 7 ... 392 - 400 are grouped by a factor 9 ... 401 - 410 are grouped by a factor 10 ... 411 - 417 are grouped by a factor 7 ... 418 - 427 are grouped by a factor 10 ... 428 - 443 are grouped by a factor 8 ... 444 - 453 are grouped by a factor 10 ... 454 - 465 are grouped by a factor 12 ... 466 - 476 are grouped by a factor 11 ... 477 - 490 are grouped by a factor 14 ... 491 - 506 are grouped by a factor 16 ... 507 - 521 are grouped by a factor 15 ... 522 - 535 are grouped by a factor 14 ... 536 - 544 are grouped by a factor 9 ... 545 - 558 are grouped by a factor 14 ... 559 - 579 are grouped by a factor 21 ... 580 - 601 are grouped by a factor 22 ... 602 - 641 are grouped by a factor 40 ... 642 - 702 are grouped by a factor 61 ... 703 - 806 are grouped by a factor 104 ... 807 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad84041000g310170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 49 by 49 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 54 46
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 114.65 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 7.75300E+03
Weighted mean angle from optical axis = 6.697 arcmin
-> Plotting ad84041000g210170_1_pi.ps from ad84041000g210170_1.pi
XSPEC 9.01 07:40:47 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad84041000g210170_1.pi
Net count rate (cts/s) for file 1 0.3396 +/- 4.1704E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad84041000g310170_1_pi.ps from ad84041000g310170_1.pi
XSPEC 9.01 07:41:01 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad84041000g310170_1.pi
Net count rate (cts/s) for file 1 0.3870 +/- 4.4483E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad84041000s010102_1_pi.ps from ad84041000s010102_1.pi
XSPEC 9.01 07:41:14 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad84041000s010102_1.pi
Net count rate (cts/s) for file 1 0.5093 +/- 5.8554E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad84041000s010212_1_pi.ps from ad84041000s010212_1.pi
XSPEC 9.01 07:41:28 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad84041000s010212_1.pi
Net count rate (cts/s) for file 1 0.5176 +/- 5.9055E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad84041000s110102_1_pi.ps from ad84041000s110102_1.pi
XSPEC 9.01 07:41:44 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad84041000s110102_1.pi
Net count rate (cts/s) for file 1 0.3782 +/- 5.0412E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad84041000s110202_1_pi.ps from ad84041000s110202_1.pi
XSPEC 9.01 07:42:00 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad84041000s110202_1.pi
Net count rate (cts/s) for file 1 0.3585 +/- 1.1390E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad84041000s110312_1_pi.ps from ad84041000s110312_1.pi
XSPEC 9.01 07:42:13 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad84041000s110312_1.pi
Net count rate (cts/s) for file 1 0.3845 +/- 5.0678E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad84041000s110412_1_pi.ps from ad84041000s110412_1.pi
XSPEC 9.01 07:42:27 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad84041000s110412_1.pi
Net count rate (cts/s) for file 1 0.3641 +/- 1.2400E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:57:51 0.10E+05 7833 1100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:57:51 0.10E+05 7833 1100
2 P1_[NEAR BRIGHT HIGH 27/07/96 14:43:39 0.46E+04 3618 1100
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:57:51 0.10E+05 7833 1100
2 P1_[NEAR BRIGHT HIGH 27/07/96 14:43:39 0.46E+04 3618 1100
3 P1_[NEAR BRIGHT MEDIUM 27/07/96 06:24:59 0.51E+02 83 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000102h.evt
Total Good Bad: Region Time Phase Cut
7833 5200 2633 0 0 0
Writing events file
5200 events written to the output file
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000202h.evt
Total Good Bad: Region Time Phase Cut
3618 2402 1216 0 0 0
Writing events file
7602 events written to the output file
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000302m.evt
Total Good Bad: Region Time Phase Cut
83 28 55 0 0 0
Writing events file
7630 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11534 7630 3904 0 0 0
in 14961.20 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad84041000s000202h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad84041000s000302m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad84041000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad84041000s000002_1.lc with binsize 98.0419172418852
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:57:51 0.15E+05 7630 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/events.tmp
Total Good Bad: Region Time Phase Cut
7630 7630 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7630 7630 0 0 0 0
in 14961.20 seconds
Fits light curve has 7630 counts for 0.5100 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT > set binsize 98.0419172418852
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad84041000s000002_1.lc
Wrote FITS light curve to file ad84041000s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad84041000s000002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad84041000s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ P1_[NEAR_A3562] Start Time (d) .... 10291 05:57:35.897
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10291 18:48:47.897
No. of Rows ....... 155 Bin Time (s) ...... 98.04
Right Ascension ... 2.0329E+02 Internal time sys.. Converted to TJD
Declination ....... -3.1699E+01 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 472 Newbins of 98.0419 (s)
Intv 1 Start10291 5:58:24
Ser.1 Avg 0.5103 Chisq 177.1 Var 0.6451E-02 Newbs. 155
Min 0.3060 Max 0.8193 expVar 0.5647E-02 Bins 155
Results from Statistical Analysis
Newbin Integration Time (s).. 98.042
Interval Duration (s)........ 46178.
No. of Newbins .............. 155
Average (c/s) ............... 0.51035 +/- 0.61E-02
Standard Deviation (c/s)..... 0.80321E-01
Minimum (c/s)................ 0.30599
Maximum (c/s)................ 0.81933
Variance ((c/s)**2).......... 0.64514E-02 +/- 0.74E-03
Expected Variance ((c/s)**2). 0.56469E-02 +/- 0.64E-03
Third Moment ((c/s)**3)...... 0.35104E-03
Average Deviation (c/s)...... 0.60726E-01
Skewness..................... 0.67745 +/- 0.20
Kurtosis..................... 1.5466 +/- 0.39
RMS fractional variation....< 0.71222E-01 (3 sigma)
Chi-Square................... 177.08 dof 154
Chi-Square Prob of constancy. 0.98138E-01 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.17895 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 472 Newbins of 98.0419 (s)
Intv 1 Start10291 5:58:24
Ser.1 Avg 0.5103 Chisq 177.1 Var 0.6451E-02 Newbs. 155
Min 0.3060 Max 0.8193 expVar 0.5647E-02 Bins 155
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=8.0000000000E+00 for ad84041000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 05:25:19 0.14E+05 9162 0011
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 05:25:19 0.14E+05 9162 0011
2 P1_[NEAR BRIGHT MEDIUM 27/07/96 06:24:59 0.34E+04 2048 0011
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 05:25:19 0.14E+05 9162 0011
2 P1_[NEAR BRIGHT MEDIUM 27/07/96 06:24:59 0.34E+04 2048 0011
3 P1_[NEAR BRIGHT HIGH 27/07/96 04:58:27 0.88E+03 602 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100102h.evt
Total Good Bad: Region Time Phase Cut
9162 5346 3816 0 0 0
Writing events file
5346 events written to the output file
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100202m.evt
Total Good Bad: Region Time Phase Cut
2048 1215 833 0 0 0
Writing events file
6561 events written to the output file
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100302h.evt
Total Good Bad: Region Time Phase Cut
602 344 258 0 0 0
Writing events file
6905 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11812 6905 4907 0 0 0
in 18430.88 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad84041000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad84041000s100302h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad84041000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad84041000s100002_1.lc with binsize 133.460420341724
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:58:27 0.18E+05 6905 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/events.tmp
Total Good Bad: Region Time Phase Cut
6905 6905 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6905 6905 0 0 0 0
in 18430.88 seconds
Fits light curve has 6905 counts for 0.3746 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT > set binsize 133.460420341724
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad84041000s100002_1.lc
Wrote FITS light curve to file ad84041000s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad84041000s100002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad84041000s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ P1_[NEAR_A3562] Start Time (d) .... 10291 05:57:35.897
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10291 18:48:47.897
No. of Rows ....... 141 Bin Time (s) ...... 133.5
Right Ascension ... 2.0329E+02 Internal time sys.. Converted to TJD
Declination ....... -3.1699E+01 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 347 Newbins of 133.460 (s)
Intv 1 Start10291 5:58:42
Ser.1 Avg 0.3749 Chisq 109.3 Var 0.2376E-02 Newbs. 141
Min 0.2473 Max 0.4795 expVar 0.3065E-02 Bins 141
Results from Statistical Analysis
Newbin Integration Time (s).. 133.46
Interval Duration (s)........ 46177.
No. of Newbins .............. 141
Average (c/s) ............... 0.37486 +/- 0.47E-02
Standard Deviation (c/s)..... 0.48748E-01
Minimum (c/s)................ 0.24726
Maximum (c/s)................ 0.47954
Variance ((c/s)**2).......... 0.23764E-02 +/- 0.28E-03
Expected Variance ((c/s)**2). 0.30652E-02 +/- 0.37E-03
Third Moment ((c/s)**3)...... 0.23518E-05
Average Deviation (c/s)...... 0.40161E-01
Skewness..................... 0.20302E-01 +/- 0.21
Kurtosis.....................-0.50695 +/- 0.41
RMS fractional variation....< 0.11645 (3 sigma)
Chi-Square................... 109.31 dof 140
Chi-Square Prob of constancy. 0.97426 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.20662 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 347 Newbins of 133.460 (s)
Intv 1 Start10291 5:58:42
Ser.1 Avg 0.3749 Chisq 109.3 Var 0.2376E-02 Newbs. 141
Min 0.2473 Max 0.4795 expVar 0.3065E-02 Bins 141
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad84041000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 14508 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 14508 1024
2 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.43E+04 4093 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 14508 1024
2 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.43E+04 4093 1024
3 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 580 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200170h.evt
Total Good Bad: Region Time Phase Cut
14508 5226 9282 0 0 0
Writing events file
5226 events written to the output file
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200270m.evt
Total Good Bad: Region Time Phase Cut
4093 1394 2699 0 0 0
Writing events file
6620 events written to the output file
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200370h.evt
Total Good Bad: Region Time Phase Cut
580 186 394 0 0 0
Writing events file
6806 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
19181 6806 12375 0 0 0
in 20040.29 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > read events ad84041000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > read events ad84041000g200370h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > filter region ad84041000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad84041000g200070_1.lc with binsize 147.225135990755
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.20E+05 6806 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/events.tmp
Total Good Bad: Region Time Phase Cut
6806 6806 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6806 6806 0 0 0 0
in 20040.29 seconds
Fits light curve has 6806 counts for 0.3396 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > set binsize 147.225135990755
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad84041000g200070_1.lc
Wrote FITS light curve to file ad84041000g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad84041000g200070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad84041000g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ P1_[NEAR_A3562] Start Time (d) .... 10291 05:53:45.883
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10291 18:48:15.897
No. of Rows ....... 141 Bin Time (s) ...... 147.2
Right Ascension ... 2.0329E+02 Internal time sys.. Converted to TJD
Declination ....... -3.1699E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 316 Newbins of 147.225 (s)
Intv 1 Start10291 5:59:53
Ser.1 Avg 0.3392 Chisq 136.9 Var 0.2427E-02 Newbs. 141
Min 0.2222 Max 0.5230 expVar 0.2501E-02 Bins 141
Results from Statistical Analysis
Newbin Integration Time (s).. 147.23
Interval Duration (s)........ 46081.
No. of Newbins .............. 141
Average (c/s) ............... 0.33924 +/- 0.42E-02
Standard Deviation (c/s)..... 0.49269E-01
Minimum (c/s)................ 0.22222
Maximum (c/s)................ 0.52300
Variance ((c/s)**2).......... 0.24274E-02 +/- 0.29E-03
Expected Variance ((c/s)**2). 0.25009E-02 +/- 0.30E-03
Third Moment ((c/s)**3)...... 0.20341E-04
Average Deviation (c/s)...... 0.38587E-01
Skewness..................... 0.17008 +/- 0.21
Kurtosis..................... 0.60355 +/- 0.41
RMS fractional variation....< 0.96253E-01 (3 sigma)
Chi-Square................... 136.86 dof 140
Chi-Square Prob of constancy. 0.55937 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.28617 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 316 Newbins of 147.225 (s)
Intv 1 Start10291 5:59:53
Ser.1 Avg 0.3392 Chisq 136.9 Var 0.2427E-02 Newbs. 141
Min 0.2222 Max 0.5230 expVar 0.2501E-02 Bins 141
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad84041000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 15430 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 15430 1024
2 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.43E+04 4310 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 15430 1024
2 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.43E+04 4310 1024
3 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 549 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300170h.evt
Total Good Bad: Region Time Phase Cut
15430 5918 9512 0 0 0
Writing events file
5918 events written to the output file
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300270m.evt
Total Good Bad: Region Time Phase Cut
4310 1619 2691 0 0 0
Writing events file
7537 events written to the output file
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300370h.evt
Total Good Bad: Region Time Phase Cut
549 216 333 0 0 0
Writing events file
7753 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
20289 7753 12536 0 0 0
in 20034.29 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > read events ad84041000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > read events ad84041000g300370h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > filter region ad84041000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad84041000g300070_1.lc with binsize 129.203440812589
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.20E+05 7753 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/events.tmp
Total Good Bad: Region Time Phase Cut
7753 7753 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7753 7753 0 0 0 0
in 20034.29 seconds
Fits light curve has 7753 counts for 0.3870 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > set binsize 129.203440812589
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad84041000g300070_1.lc
Wrote FITS light curve to file ad84041000g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad84041000g300070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad84041000g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ P1_[NEAR_A3562] Start Time (d) .... 10291 05:53:47.883
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10291 18:48:15.897
No. of Rows ....... 160 Bin Time (s) ...... 129.2
Right Ascension ... 2.0329E+02 Internal time sys.. Converted to TJD
Declination ....... -3.1699E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 360 Newbins of 129.203 (s)
Intv 1 Start10291 5:59:10
Ser.1 Avg 0.3861 Chisq 159.4 Var 0.3205E-02 Newbs. 160
Min 0.2596 Max 0.6006 expVar 0.3218E-02 Bins 160
Results from Statistical Analysis
Newbin Integration Time (s).. 129.20
Interval Duration (s)........ 46126.
No. of Newbins .............. 160
Average (c/s) ............... 0.38613 +/- 0.45E-02
Standard Deviation (c/s)..... 0.56617E-01
Minimum (c/s)................ 0.25961
Maximum (c/s)................ 0.60063
Variance ((c/s)**2).......... 0.32054E-02 +/- 0.36E-03
Expected Variance ((c/s)**2). 0.32181E-02 +/- 0.36E-03
Third Moment ((c/s)**3)...... 0.78555E-04
Average Deviation (c/s)...... 0.45423E-01
Skewness..................... 0.43286 +/- 0.19
Kurtosis..................... 0.42941 +/- 0.39
RMS fractional variation....< 0.89889E-01 (3 sigma)
Chi-Square................... 159.37 dof 159
Chi-Square Prob of constancy. 0.47685 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.51097 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 360 Newbins of 129.203 (s)
Intv 1 Start10291 5:59:10
Ser.1 Avg 0.3861 Chisq 159.4 Var 0.3205E-02 Newbs. 160
Min 0.2596 Max 0.6006 expVar 0.3218E-02 Bins 160
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad84041000g200170h.evt[2] ad84041000g200270m.evt[2] ad84041000g200370h.evt[2]-> Making L1 light curve of ft960727_0447_1900G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 39003 output records from 39040 good input G2_L1 records.-> Making L1 light curve of ft960727_0447_1900G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 18971 output records from 43145 good input G2_L1 records.-> Merging GTIs from the following files:
ad84041000g300170h.evt[2] ad84041000g300270m.evt[2] ad84041000g300370h.evt[2]-> Making L1 light curve of ft960727_0447_1900G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 38361 output records from 38398 good input G3_L1 records.-> Making L1 light curve of ft960727_0447_1900G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 18926 output records from 42475 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 14508 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200170h.evt
Total Good Bad: Region Time Phase Cut
14508 5226 9282 0 0 0
Writing events file
5226 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14508 5226 9282 0 0 0
in 15186.54 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > filter region ad84041000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad84041000g200170h_1.ulc use_events=yes
Wrote events list to file ad84041000g200170h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad84041000g200270m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.43E+04 4093 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200270m.evt
Total Good Bad: Region Time Phase Cut
4093 1394 2699 0 0 0
Writing events file
1394 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4093 1394 2699 0 0 0
in 4287.75 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > filter region ad84041000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad84041000g200270m_1.ulc use_events=yes
Wrote events list to file ad84041000g200270m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad84041000g200370h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 580 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200370h.evt
Total Good Bad: Region Time Phase Cut
580 186 394 0 0 0
Writing events file
186 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
580 186 394 0 0 0
in 566.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000g200370h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > filter region ad84041000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad84041000g200370h_1.ulc use_events=yes
Wrote events list to file ad84041000g200370h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad84041000g300170h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.15E+05 15430 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300170h.evt
Total Good Bad: Region Time Phase Cut
15430 5918 9512 0 0 0
Writing events file
5918 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15430 5918 9512 0 0 0
in 15180.54 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > filter region ad84041000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad84041000g300170h_1.ulc use_events=yes
Wrote events list to file ad84041000g300170h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad84041000g300270m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.43E+04 4310 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300270m.evt
Total Good Bad: Region Time Phase Cut
4310 1619 2691 0 0 0
Writing events file
1619 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4310 1619 2691 0 0 0
in 4287.75 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > filter region ad84041000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad84041000g300270m_1.ulc use_events=yes
Wrote events list to file ad84041000g300270m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad84041000g300370h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 549 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300370h.evt
Total Good Bad: Region Time Phase Cut
549 216 333 0 0 0
Writing events file
216 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
549 216 333 0 0 0
in 566.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000g300370h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > filter region ad84041000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad84041000g300370h_1.ulc use_events=yes
Wrote events list to file ad84041000g300370h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad84041000s000102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:57:51 0.10E+05 7833 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000102h.evt
Total Good Bad: Region Time Phase Cut
7833 5200 2633 0 0 0
Writing events file
5200 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7833 5200 2633 0 0 0
in 10292.25 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad84041000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad84041000s000102h_1.ulc use_events=yes
Wrote events list to file ad84041000s000102h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad84041000s000112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 04:57:51 0.10E+05 8006 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000112h.evt
Total Good Bad: Region Time Phase Cut
8006 5292 2714 0 0 0
Writing events file
5292 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8006 5292 2714 0 0 0
in 10292.25 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad84041000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad84041000s000112h_1.ulc use_events=yes
Wrote events list to file ad84041000s000112h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad84041000s000202h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 14:43:39 0.46E+04 3618 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000202h.evt
Total Good Bad: Region Time Phase Cut
3618 2402 1216 0 0 0
Writing events file
2402 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3618 2402 1216 0 0 0
in 4617.66 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad84041000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad84041000s000202h_1.ulc use_events=yes
Wrote events list to file ad84041000s000202h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad84041000s000212h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 14:43:39 0.46E+04 3704 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000212h.evt
Total Good Bad: Region Time Phase Cut
3704 2434 1270 0 0 0
Writing events file
2434 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3704 2434 1270 0 0 0
in 4617.66 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s000212h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad84041000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad84041000s000212h_1.ulc use_events=yes
Wrote events list to file ad84041000s000212h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad84041000s000302m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT MEDIUM 27/07/96 06:24:59 0.51E+02 83 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000302m.evt
Total Good Bad: Region Time Phase Cut
83 28 55 0 0 0
Writing events file
28 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
83 28 55 0 0 0
in 51.28 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s000302m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad84041000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad84041000s000302m_1.ulc use_events=yes
Wrote events list to file ad84041000s000302m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad84041000s000312m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 MEDIUM 27/07/96 06:24:59 0.51E+02 83 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000312m.evt
Total Good Bad: Region Time Phase Cut
83 28 55 0 0 0
Writing events file
28 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
83 28 55 0 0 0
in 51.28 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s000312m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad84041000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad84041000s000312m_1.ulc use_events=yes
Wrote events list to file ad84041000s000312m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad84041000s100102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 05:25:19 0.14E+05 9162 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100102h.evt
Total Good Bad: Region Time Phase Cut
9162 5346 3816 0 0 0
Writing events file
5346 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9162 5346 3816 0 0 0
in 14161.83 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad84041000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad84041000s100102h_1.ulc use_events=yes
Wrote events list to file ad84041000s100102h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad84041000s100112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 05:25:19 0.14E+05 9383 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100112h.evt
Total Good Bad: Region Time Phase Cut
9383 5435 3948 0 0 0
Writing events file
5435 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9383 5435 3948 0 0 0
in 14161.83 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad84041000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad84041000s100112h_1.ulc use_events=yes
Wrote events list to file ad84041000s100112h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad84041000s100202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT MEDIUM 27/07/96 06:24:59 0.34E+04 2048 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100202m.evt
Total Good Bad: Region Time Phase Cut
2048 1215 833 0 0 0
Writing events file
1215 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2048 1215 833 0 0 0
in 3389.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad84041000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad84041000s100202m_1.ulc use_events=yes
Wrote events list to file ad84041000s100202m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad84041000s100212m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 MEDIUM 27/07/96 06:24:59 0.34E+04 2076 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100212m.evt
Total Good Bad: Region Time Phase Cut
2076 1234 842 0 0 0
Writing events file
1234 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2076 1234 842 0 0 0
in 3389.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s100212m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad84041000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad84041000s100212m_1.ulc use_events=yes
Wrote events list to file ad84041000s100212m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad84041000s100302h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:58:27 0.88E+03 602 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100302h.evt
Total Good Bad: Region Time Phase Cut
602 344 258 0 0 0
Writing events file
344 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
602 344 258 0 0 0
in 880.06 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s100302h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad84041000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad84041000s100302h_1.ulc use_events=yes
Wrote events list to file ad84041000s100302h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad84041000s100312h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 04:58:27 0.88E+03 617 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100312h.evt
Total Good Bad: Region Time Phase Cut
617 349 268 0 0 0
Writing events file
349 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
617 349 268 0 0 0
in 880.06 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000s100312h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad84041000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad84041000s100312h_1.ulc use_events=yes
Wrote events list to file ad84041000s100312h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/84041000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) ***
total number of superframes: 12954
frame data: 112598079.891591 ---> 112598223.891096
S0, C0, 2 ccd mode; Output File = fr960727_0447.1900_s0c0m2a.fits
frame data: 112598243.891028 ---> 112598387.890533
S0, C1, 2 ccd mode; Output File = fr960727_0447.1900_s0c1m2a.fits
frame data: 112598407.890464 ---> 112598551.889969
S0, C0, 2 ccd mode; Output File = fr960727_0447.1900_s0c0m2b.fits
frame data: 112598571.889901 ---> 112598715.889406
S0, C1, 2 ccd mode; Output File = fr960727_0447.1900_s0c1m2b.fits
frame data: 112609547.851517 ---> 112609691.851027
S1, C2, 2 ccd mode; Output File = fr960727_0447.1900_s1c2m2a.fits
frame data: 112609711.850959 ---> 112609855.850469
S1, C3, 2 ccd mode; Output File = fr960727_0447.1900_s1c3m2a.fits
frame data: 112609875.850401 ---> 112610019.849911
S1, C2, 2 ccd mode; Output File = fr960727_0447.1900_s1c2m2b.fits
frame data: 112610039.849843 ---> 112610183.849353
S1, C3, 2 ccd mode; Output File = fr960727_0447.1900_s1c3m2b.fits
frame data: 112615299.831511 ---> 112615443.831025
S0, C0, 2 ccd mode; Output File = fr960727_0447.1900_s0c0m2c.fits
frame data: 112615463.830957 ---> 112615607.830471
S0, C1, 2 ccd mode; Output File = fr960727_0447.1900_s0c1m2c.fits
frame data: 112615627.830404 ---> 112615771.829917
S0, C0, 2 ccd mode; Output File = fr960727_0447.1900_s0c0m2d.fits
frame data: 112615791.82985 ---> 112615935.829364
S0, C1, 2 ccd mode; Output File = fr960727_0447.1900_s0c1m2d.fits
Total of 12 sets of frame data are extracted.
-> Processing fr960727_0447.1900_s0c0m2a.fitsDark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960727_0447.1900_s0c0m2a.fits Output zero level image : rdd.tmp Bias level = 337-> Adding keywords to header of fr960727_0447.1900_s0c0m2a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960727_0447.1900_s0c0m2b.fits Output zero level image : rdd.tmp Bias level = 337-> Adding keywords to header of fr960727_0447.1900_s0c0m2b.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960727_0447.1900_s0c0m2c.fits Output zero level image : rdd.tmp Bias level = 337-> Adding keywords to header of fr960727_0447.1900_s0c0m2c.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960727_0447.1900_s0c0m2d.fits Output zero level image : rdd.tmp Bias level = 337-> Adding keywords to header of fr960727_0447.1900_s0c0m2d.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960727_0447.1900_s0c1m2a.fits Output zero level image : rdd.tmp Bias level = 300-> Adding keywords to header of fr960727_0447.1900_s0c1m2a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960727_0447.1900_s0c1m2b.fits Output zero level image : rdd.tmp Bias level = 300-> Adding keywords to header of fr960727_0447.1900_s0c1m2b.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960727_0447.1900_s0c1m2c.fits Output zero level image : rdd.tmp Bias level = 300-> Adding keywords to header of fr960727_0447.1900_s0c1m2c.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960727_0447.1900_s0c1m2d.fits Output zero level image : rdd.tmp Bias level = 300-> Adding keywords to header of fr960727_0447.1900_s0c1m2d.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960727_0447.1900_s1c2m2a.fits Output zero level image : rdd.tmp Bias level = 183-> Adding keywords to header of fr960727_0447.1900_s1c2m2a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960727_0447.1900_s1c2m2b.fits Output zero level image : rdd.tmp Bias level = 183-> Adding keywords to header of fr960727_0447.1900_s1c2m2b.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960727_0447.1900_s1c3m2a.fits Output zero level image : rdd.tmp Bias level = 220-> Adding keywords to header of fr960727_0447.1900_s1c3m2a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr960727_0447.1900_s1c3m2b.fits Output zero level image : rdd.tmp Bias level = 220-> Adding keywords to header of fr960727_0447.1900_s1c3m2b.fits
1 ad84041000g200170h.unf 40089 1 ad84041000g200270m.unf 40089 1 ad84041000g200370h.unf 40089-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.19E+05 26903 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.19E+05 26903 1024
2 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.13E+05 12274 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.19E+05 26903 1024
2 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.13E+05 12274 1024
3 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 912 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200170h.unf
Total Good Bad: Region Time Phase Cut
26903 3933 22970 0 0 0
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200270m.unf
Total Good Bad: Region Time Phase Cut
12274 2488 9786 0 0 0
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200370h.unf
Total Good Bad: Region Time Phase Cut
912 119 793 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
40089 6540 33549 0 0 0
in 33199.89 seconds
Spectrum has 6540 counts for 0.1970 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 33200. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad84041000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > read events ad84041000g200270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > read events ad84041000g200370h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad84041000g220170.cal group=yes
Wrote spectrum to ad84041000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 08:07:11 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad84041000g220170.cal
Net count rate (cts/s) for file 1 0.1970 +/- 2.4385E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.1219E+06 using 84 PHA bins.
Reduced chi-squared = 1.4570E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.1154E+06 using 84 PHA bins.
Reduced chi-squared = 1.4300E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.1154E+06 using 84 PHA bins.
Reduced chi-squared = 1.4119E+04
!XSPEC> renorm
Chi-Squared = 1774. using 84 PHA bins.
Reduced chi-squared = 22.45
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
1348.7 0 1.000 5.894 0.1195 5.7334E-02
5.0498E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
529.39 0 1.000 5.866 0.1693 8.5418E-02
4.4568E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
200.15 -1 1.000 5.919 0.1899 0.1208
2.9178E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
179.32 -2 1.000 5.951 0.2040 0.1337
2.0312E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
176.03 -3 1.000 5.935 0.1905 0.1299
2.4044E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
175.67 -4 1.000 5.942 0.1950 0.1316
2.2308E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
175.48 -5 1.000 5.939 0.1925 0.1309
2.3060E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
175.47 -1 1.000 5.940 0.1931 0.1311
2.2856E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.93970 +/- 0.76453E-02
3 3 2 gaussian/b Sigma 0.193083 +/- 0.79242E-02
4 4 2 gaussian/b norm 0.131069 +/- 0.26655E-02
5 2 3 gaussian/b LineE 6.53964 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.202599 = par 3 * 1.0493
7 5 3 gaussian/b norm 2.285557E-02 +/- 0.19315E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 175.5 using 84 PHA bins.
Reduced chi-squared = 2.221
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad84041000g220170.cal peaks at 5.93970 +/- 0.0076453 keV1 ad84041000g300170h.unf 39228 1 ad84041000g300270m.unf 39228 1 ad84041000g300370h.unf 39228-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.19E+05 26476 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.19E+05 26476 1024
2 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.13E+05 11940 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.19E+05 26476 1024
2 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.13E+05 11940 1024
3 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 812 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300170h.unf
Total Good Bad: Region Time Phase Cut
26476 3256 23220 0 0 0
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300270m.unf
Total Good Bad: Region Time Phase Cut
11940 2340 9600 0 0 0
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300370h.unf
Total Good Bad: Region Time Phase Cut
812 80 732 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
39228 5676 33552 0 0 0
in 33193.89 seconds
Spectrum has 5676 counts for 0.1710 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 33194. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad84041000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!xsel:ASCA > read events ad84041000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > read events ad84041000g300270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > read events ad84041000g300370h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad84041000g320170.cal group=yes
Wrote spectrum to ad84041000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 08:08:08 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad84041000g320170.cal
Net count rate (cts/s) for file 1 0.1710 +/- 2.2731E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.2844E+06 using 84 PHA bins.
Reduced chi-squared = 1.6680E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.2730E+06 using 84 PHA bins.
Reduced chi-squared = 1.6321E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.2730E+06 using 84 PHA bins.
Reduced chi-squared = 1.6114E+04
!XSPEC> renorm
Chi-Squared = 1928. using 84 PHA bins.
Reduced chi-squared = 24.40
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
1544.1 0 1.000 5.893 9.1414E-02 5.2078E-02
4.4713E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
611.16 0 1.000 5.865 0.1386 8.1803E-02
3.8674E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
192.47 -1 1.000 5.920 0.1526 0.1167
2.4694E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
128.48 -2 1.000 5.962 0.1724 0.1330
1.5342E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
126.98 -3 1.000 5.956 0.1652 0.1321
1.6347E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
126.95 -4 1.000 5.957 0.1650 0.1322
1.6226E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
126.94 -5 1.000 5.957 0.1649 0.1322
1.6246E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.95702 +/- 0.59843E-02
3 3 2 gaussian/b Sigma 0.164889 +/- 0.72230E-02
4 4 2 gaussian/b norm 0.132188 +/- 0.23536E-02
5 2 3 gaussian/b LineE 6.55871 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.173016 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.624553E-02 +/- 0.13909E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 126.9 using 84 PHA bins.
Reduced chi-squared = 1.607
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad84041000g320170.cal peaks at 5.95702 +/- 0.0059843 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:57:51 0.14E+05 172092 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000102h.unf
Total Good Bad: Region Time Phase Cut
172092 17403 0 154689 0 0
Writing events file
17403 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
172092 17403 0 154689 0 0
in 1465.66 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad84041000s000102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s000102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 17403
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 74 10777
Flickering pixels iter, pixels & cnts : 1 31 470
cleaning chip # 1
Hot pixels & counts : 39 4955
Flickering pixels iter, pixels & cnts : 1 16 206
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 160
Number of (internal) image counts : 17403
Number of image cts rejected (N, %) : 16408 94.2825928
By chip : 0 1 2 3
Pixels rejected : 105 55 0 0
Image counts : 11570 5833 0 0
Image cts rejected: 11247 5161 0 0
Image cts rej (%) : 97.21 88.48 0.00 0.00
filtering data...
Total counts : 11570 5833 0 0
Total cts rejected: 11247 5161 0 0
Total cts rej (%) : 97.21 88.48 0.00 0.00
Number of clean counts accepted : 995
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 160
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s000112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 04:57:51 0.14E+05 172803 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000112h.unf
Total Good Bad: Region Time Phase Cut
172803 17728 0 155075 0 0
Writing events file
17728 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
172803 17728 0 155075 0 0
in 1465.66 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad84041000s000112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s000112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 17728
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 74 10785
Flickering pixels iter, pixels & cnts : 1 31 470
cleaning chip # 1
Hot pixels & counts : 39 4957
Flickering pixels iter, pixels & cnts : 1 16 208
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 160
Number of (internal) image counts : 17728
Number of image cts rejected (N, %) : 16420 92.6218414
By chip : 0 1 2 3
Pixels rejected : 105 55 0 0
Image counts : 11714 6014 0 0
Image cts rejected: 11255 5165 0 0
Image cts rej (%) : 96.08 85.88 0.00 0.00
filtering data...
Total counts : 11714 6014 0 0
Total cts rejected: 11255 5165 0 0
Total cts rej (%) : 96.08 85.88 0.00 0.00
Number of clean counts accepted : 1308
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 160
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s000202h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 14:43:39 0.63E+04 77564 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000202h.unf
Total Good Bad: Region Time Phase Cut
77564 1472 0 76092 0 0
Writing events file
1472 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
77564 1472 0 76092 0 0
in 127.81 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad84041000s000202h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s000202h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1472
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 57 870
Flickering pixels iter, pixels & cnts : 1 20 116
cleaning chip # 1
Hot pixels & counts : 30 401
Flickering pixels iter, pixels & cnts : 1 10 41
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 117
Number of (internal) image counts : 1472
Number of image cts rejected (N, %) : 1428 97.0108719
By chip : 0 1 2 3
Pixels rejected : 77 40 0 0
Image counts : 1009 463 0 0
Image cts rejected: 986 442 0 0
Image cts rej (%) : 97.72 95.46 0.00 0.00
filtering data...
Total counts : 1009 463 0 0
Total cts rejected: 986 442 0 0
Total cts rej (%) : 97.72 95.46 0.00 0.00
Number of clean counts accepted : 44
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 117
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s000212h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 14:43:39 0.63E+04 77873 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000212h.unf
Total Good Bad: Region Time Phase Cut
77873 1473 0 76400 0 0
Writing events file
1473 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
77873 1473 0 76400 0 0
in 127.81 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad84041000s000212h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s000212h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1473
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 57 870
Flickering pixels iter, pixels & cnts : 1 20 116
cleaning chip # 1
Hot pixels & counts : 30 401
Flickering pixels iter, pixels & cnts : 1 10 41
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 117
Number of (internal) image counts : 1473
Number of image cts rejected (N, %) : 1428 96.9450073
By chip : 0 1 2 3
Pixels rejected : 77 40 0 0
Image counts : 1009 464 0 0
Image cts rejected: 986 442 0 0
Image cts rej (%) : 97.72 95.26 0.00 0.00
filtering data...
Total counts : 1009 464 0 0
Total cts rejected: 986 442 0 0
Total cts rej (%) : 97.72 95.26 0.00 0.00
Number of clean counts accepted : 45
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 117
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s000302m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT MEDIUM 27/07/96 06:24:59 0.88E+04 36994 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000302m.unf
Total Good Bad: Region Time Phase Cut
36994 14577 0 22417 0 0
Writing events file
14577 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
36994 14577 0 22417 0 0
in 3884.63 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s000302m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad84041000s000302m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s000302m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 14577
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 37 11680
Flickering pixels iter, pixels & cnts : 1 14 164
cleaning chip # 1
Hot pixels & counts : 11 2268
Flickering pixels iter, pixels & cnts : 1 16 113
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 78
Number of (internal) image counts : 14577
Number of image cts rejected (N, %) : 14225 97.5852356
By chip : 0 1 2 3
Pixels rejected : 51 27 0 0
Image counts : 12009 2568 0 0
Image cts rejected: 11844 2381 0 0
Image cts rej (%) : 98.63 92.72 0.00 0.00
filtering data...
Total counts : 12009 2568 0 0
Total cts rejected: 11844 2381 0 0
Total cts rej (%) : 98.63 92.72 0.00 0.00
Number of clean counts accepted : 352
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 78
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s000312m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 MEDIUM 27/07/96 06:24:59 0.88E+04 37178 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000312m.unf
Total Good Bad: Region Time Phase Cut
37178 14654 0 22524 0 0
Writing events file
14654 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
37178 14654 0 22524 0 0
in 3884.63 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s000312m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad84041000s000312m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s000312m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 14654
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 37 11680
Flickering pixels iter, pixels & cnts : 1 14 164
cleaning chip # 1
Hot pixels & counts : 11 2269
Flickering pixels iter, pixels & cnts : 1 17 117
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 79
Number of (internal) image counts : 14654
Number of image cts rejected (N, %) : 14230 97.1065903
By chip : 0 1 2 3
Pixels rejected : 51 28 0 0
Image counts : 12036 2618 0 0
Image cts rejected: 11844 2386 0 0
Image cts rej (%) : 98.40 91.14 0.00 0.00
filtering data...
Total counts : 12036 2618 0 0
Total cts rejected: 11844 2386 0 0
Total cts rej (%) : 98.40 91.14 0.00 0.00
Number of clean counts accepted : 424
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 79
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s000402m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT MEDIUM 27/07/96 14:50:19 0.64E+04 22085 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000402m.unf
Total Good Bad: Region Time Phase Cut
22085 16796 0 5289 0 0
Writing events file
16796 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
22085 16796 0 5289 0 0
in 4868.13 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s000402m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad84041000s000402m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s000402m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 16796
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 27 13063
Flickering pixels iter, pixels & cnts : 1 13 190
cleaning chip # 1
Hot pixels & counts : 12 3102
Flickering pixels iter, pixels & cnts : 1 19 165
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 71
Number of (internal) image counts : 16796
Number of image cts rejected (N, %) : 16520 98.3567505
By chip : 0 1 2 3
Pixels rejected : 40 31 0 0
Image counts : 13382 3414 0 0
Image cts rejected: 13253 3267 0 0
Image cts rej (%) : 99.04 95.69 0.00 0.00
filtering data...
Total counts : 13382 3414 0 0
Total cts rejected: 13253 3267 0 0
Total cts rej (%) : 99.04 95.69 0.00 0.00
Number of clean counts accepted : 276
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 71
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s000412m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 MEDIUM 27/07/96 14:50:19 0.64E+04 22211 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000412m.unf
Total Good Bad: Region Time Phase Cut
22211 16887 0 5324 0 0
Writing events file
16887 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
22211 16887 0 5324 0 0
in 4868.13 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s000412m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad84041000s000412m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s000412m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 16887
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 27 13085
Flickering pixels iter, pixels & cnts : 1 14 194
cleaning chip # 1
Hot pixels & counts : 12 3106
Flickering pixels iter, pixels & cnts : 1 19 166
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 72
Number of (internal) image counts : 16887
Number of image cts rejected (N, %) : 16551 98.0103073
By chip : 0 1 2 3
Pixels rejected : 41 31 0 0
Image counts : 13434 3453 0 0
Image cts rejected: 13279 3272 0 0
Image cts rej (%) : 98.85 94.76 0.00 0.00
filtering data...
Total counts : 13434 3453 0 0
Total cts rejected: 13279 3272 0 0
Total cts rej (%) : 98.85 94.76 0.00 0.00
Number of clean counts accepted : 336
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 72
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s000502l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT LOW 27/07/96 07:01:31 0.12E+04 1013 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000502l.unf
Total Good Bad: Region Time Phase Cut
1013 222 0 791 0 0
Writing events file
222 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1013 222 0 791 0 0
in 417.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s000502l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad84041000s000502l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s000502l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 222
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 5 76
Flickering pixels iter, pixels & cnts : 1 5 24
cleaning chip # 1
Hot pixels & counts : 8 71
Flickering pixels iter, pixels & cnts : 1 2 6
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 20
Number of (internal) image counts : 222
Number of image cts rejected (N, %) : 177 79.7297287
By chip : 0 1 2 3
Pixels rejected : 10 10 0 0
Image counts : 121 101 0 0
Image cts rejected: 100 77 0 0
Image cts rej (%) : 82.64 76.24 0.00 0.00
filtering data...
Total counts : 121 101 0 0
Total cts rejected: 100 77 0 0
Total cts rej (%) : 82.64 76.24 0.00 0.00
Number of clean counts accepted : 45
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 20
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s000512l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 P1_[NEAR BRIGHT2 LOW 27/07/96 07:01:31 0.12E+04 1034 1100
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s000512l.unf
Total Good Bad: Region Time Phase Cut
1034 238 0 796 0 0
Writing events file
238 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1034 238 0 796 0 0
in 417.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s000512l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad84041000s000512l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s000512l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 238
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 5 76
Flickering pixels iter, pixels & cnts : 1 5 24
cleaning chip # 1
Hot pixels & counts : 8 72
Flickering pixels iter, pixels & cnts : 1 2 6
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 20
Number of (internal) image counts : 238
Number of image cts rejected (N, %) : 178 74.7899170
By chip : 0 1 2 3
Pixels rejected : 10 10 0 0
Image counts : 130 108 0 0
Image cts rejected: 100 78 0 0
Image cts rej (%) : 76.92 72.22 0.00 0.00
filtering data...
Total counts : 130 108 0 0
Total cts rejected: 100 78 0 0
Total cts rej (%) : 76.92 72.22 0.00 0.00
Number of clean counts accepted : 60
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 20
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s100102h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 05:25:19 0.18E+05 231436 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100102h.unf
Total Good Bad: Region Time Phase Cut
231436 17710 0 213726 0 0
Writing events file
17710 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
231436 17710 0 213726 0 0
in 1467.57 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad84041000s100102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s100102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 17710
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 56 7984
Flickering pixels iter, pixels & cnts : 1 34 452
cleaning chip # 3
Hot pixels & counts : 53 7923
Flickering pixels iter, pixels & cnts : 1 31 436
Number of pixels rejected : 174
Number of (internal) image counts : 17710
Number of image cts rejected (N, %) : 16795 94.8334274
By chip : 0 1 2 3
Pixels rejected : 0 0 90 84
Image counts : 0 0 8841 8869
Image cts rejected: 0 0 8436 8359
Image cts rej (%) : 0.00 0.00 95.42 94.25
filtering data...
Total counts : 0 0 8841 8869
Total cts rejected: 0 0 8436 8359
Total cts rej (%) : 0.00 0.00 95.42 94.25
Number of clean counts accepted : 915
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 174
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s100112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 05:25:19 0.18E+05 232286 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100112h.unf
Total Good Bad: Region Time Phase Cut
232286 17979 0 214307 0 0
Writing events file
17979 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
232286 17979 0 214307 0 0
in 1467.57 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad84041000s100112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s100112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 17979
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 56 7992
Flickering pixels iter, pixels & cnts : 1 34 454
cleaning chip # 3
Hot pixels & counts : 53 7932
Flickering pixels iter, pixels & cnts : 1 31 444
Number of pixels rejected : 174
Number of (internal) image counts : 17979
Number of image cts rejected (N, %) : 16822 93.5647125
By chip : 0 1 2 3
Pixels rejected : 0 0 90 84
Image counts : 0 0 8979 9000
Image cts rejected: 0 0 8446 8376
Image cts rej (%) : 0.00 0.00 94.06 93.07
filtering data...
Total counts : 0 0 8979 9000
Total cts rejected: 0 0 8446 8376
Total cts rej (%) : 0.00 0.00 94.06 93.07
Number of clean counts accepted : 1157
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 174
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s100202m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT MEDIUM 27/07/96 06:24:59 0.15E+05 57567 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100202m.unf
Total Good Bad: Region Time Phase Cut
57567 31183 0 26384 0 0
Writing events file
31183 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57567 31183 0 26384 0 0
in 8752.76 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad84041000s100202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 31183
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 30 14474
Flickering pixels iter, pixels & cnts : 1 18 219
cleaning chip # 3
Hot pixels & counts : 24 15629
Flickering pixels iter, pixels & cnts : 1 20 254
Number of pixels rejected : 92
Number of (internal) image counts : 31183
Number of image cts rejected (N, %) : 30576 98.0534286
By chip : 0 1 2 3
Pixels rejected : 0 0 48 44
Image counts : 0 0 15023 16160
Image cts rejected: 0 0 14693 15883
Image cts rej (%) : 0.00 0.00 97.80 98.29
filtering data...
Total counts : 0 0 15023 16160
Total cts rejected: 0 0 14693 15883
Total cts rej (%) : 0.00 0.00 97.80 98.29
Number of clean counts accepted : 607
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 92
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s100212m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 MEDIUM 27/07/96 06:24:59 0.15E+05 57774 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100212m.unf
Total Good Bad: Region Time Phase Cut
57774 31267 0 26507 0 0
Writing events file
31267 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57774 31267 0 26507 0 0
in 8752.76 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s100212m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad84041000s100212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s100212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 31267
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 30 14478
Flickering pixels iter, pixels & cnts : 1 18 219
cleaning chip # 3
Hot pixels & counts : 24 15640
Flickering pixels iter, pixels & cnts : 1 20 256
Number of pixels rejected : 92
Number of (internal) image counts : 31267
Number of image cts rejected (N, %) : 30593 97.8443756
By chip : 0 1 2 3
Pixels rejected : 0 0 48 44
Image counts : 0 0 15060 16207
Image cts rejected: 0 0 14697 15896
Image cts rej (%) : 0.00 0.00 97.59 98.08
filtering data...
Total counts : 0 0 15060 16207
Total cts rejected: 0 0 14697 15896
Total cts rej (%) : 0.00 0.00 97.59 98.08
Number of clean counts accepted : 674
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 92
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s100302h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT HIGH 27/07/96 04:58:27 0.16E+04 20616 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100302h.unf
Total Good Bad: Region Time Phase Cut
20616 1362 0 19254 0 0
Writing events file
1362 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
20616 1362 0 19254 0 0
in 119.87 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s100302h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad84041000s100302h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s100302h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1362
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 44 607
Flickering pixels iter, pixels & cnts : 1 12 74
cleaning chip # 3
Hot pixels & counts : 42 556
Flickering pixels iter, pixels & cnts : 1 15 80
Number of pixels rejected : 113
Number of (internal) image counts : 1362
Number of image cts rejected (N, %) : 1317 96.6960373
By chip : 0 1 2 3
Pixels rejected : 0 0 56 57
Image counts : 0 0 706 656
Image cts rejected: 0 0 681 636
Image cts rej (%) : 0.00 0.00 96.46 96.95
filtering data...
Total counts : 0 0 706 656
Total cts rejected: 0 0 681 636
Total cts rej (%) : 0.00 0.00 96.46 96.95
Number of clean counts accepted : 45
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 113
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s100312h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 HIGH 27/07/96 04:58:27 0.16E+04 20665 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100312h.unf
Total Good Bad: Region Time Phase Cut
20665 1366 0 19299 0 0
Writing events file
1366 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
20665 1366 0 19299 0 0
in 119.87 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s100312h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad84041000s100312h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s100312h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1366
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 44 607
Flickering pixels iter, pixels & cnts : 1 12 74
cleaning chip # 3
Hot pixels & counts : 42 557
Flickering pixels iter, pixels & cnts : 1 15 80
Number of pixels rejected : 113
Number of (internal) image counts : 1366
Number of image cts rejected (N, %) : 1318 96.4860916
By chip : 0 1 2 3
Pixels rejected : 0 0 56 57
Image counts : 0 0 709 657
Image cts rejected: 0 0 681 637
Image cts rej (%) : 0.00 0.00 96.05 96.96
filtering data...
Total counts : 0 0 709 657
Total cts rejected: 0 0 681 637
Total cts rej (%) : 0.00 0.00 96.05 96.96
Number of clean counts accepted : 48
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 113
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s100402l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT LOW 27/07/96 07:01:31 0.13E+04 1370 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100402l.unf
Total Good Bad: Region Time Phase Cut
1370 274 0 1096 0 0
Writing events file
274 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1370 274 0 1096 0 0
in 417.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s100402l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad84041000s100402l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s100402l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 274
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 5 102
Flickering pixels iter, pixels & cnts : 1 8 36
cleaning chip # 3
Hot pixels & counts : 5 82
Flickering pixels iter, pixels & cnts : 1 2 8
Number of pixels rejected : 20
Number of (internal) image counts : 274
Number of image cts rejected (N, %) : 228 83.2116776
By chip : 0 1 2 3
Pixels rejected : 0 0 13 7
Image counts : 0 0 157 117
Image cts rejected: 0 0 138 90
Image cts rej (%) : 0.00 0.00 87.90 76.92
filtering data...
Total counts : 0 0 157 117
Total cts rejected: 0 0 138 90
Total cts rej (%) : 0.00 0.00 87.90 76.92
Number of clean counts accepted : 46
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 20
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000s100412l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 P1_[NEAR BRIGHT2 LOW 27/07/96 07:01:31 0.13E+04 1382 0011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000s100412l.unf
Total Good Bad: Region Time Phase Cut
1382 279 0 1103 0 0
Writing events file
279 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1382 279 0 1103 0 0
in 417.09 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000s100412l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad84041000s100412l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad84041000s100412l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 279
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 5 103
Flickering pixels iter, pixels & cnts : 1 8 36
cleaning chip # 3
Hot pixels & counts : 5 82
Flickering pixels iter, pixels & cnts : 1 2 8
Number of pixels rejected : 20
Number of (internal) image counts : 279
Number of image cts rejected (N, %) : 229 82.0788498
By chip : 0 1 2 3
Pixels rejected : 0 0 13 7
Image counts : 0 0 160 119
Image cts rejected: 0 0 139 90
Image cts rej (%) : 0.00 0.00 86.88 75.63
filtering data...
Total counts : 0 0 160 119
Total cts rejected: 0 0 139 90
Total cts rej (%) : 0.00 0.00 86.88 75.63
Number of clean counts accepted : 50
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 20
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad84041000g200170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.19E+05 26903 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200170h.unf
Total Good Bad: Region Time Phase Cut
26903 1453 0 25450 0 0
Writing events file
1453 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26903 1453 0 25450 0 0
in 2637.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad84041000g200170h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.19E+05 26903 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/84041000.005/ad84041000g200170h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad84041000g200170h.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.13E+05 12274 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200270m.unf
Total Good Bad: Region Time Phase Cut
12274 4401 0 7873 0 0
Writing events file
4401 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12274 4401 0 7873 0 0
in 8064.16 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad84041000g200270m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.13E+05 12274 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g200270m.unf
Total Good Bad: Region Time Phase Cut
12274 239 0 12035 0 0
Writing events file
239 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12274 239 0 12035 0 0
in 323.89 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad84041000g200370h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 912 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/84041000.005/ad84041000g200370h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000g200370h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad84041000g200370h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 912 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/84041000.005/ad84041000g200370h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000g200370h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad84041000g200370h.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.19E+05 26476 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300170h.unf
Total Good Bad: Region Time Phase Cut
26476 1342 0 25134 0 0
Writing events file
1342 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26476 1342 0 25134 0 0
in 2637.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad84041000g300170h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 04:56:03 0.19E+05 26476 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/84041000.005/ad84041000g300170h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad84041000g300170h.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.13E+05 11940 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300270m.unf
Total Good Bad: Region Time Phase Cut
11940 4233 0 7707 0 0
Writing events file
4233 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11940 4233 0 7707 0 0
in 8064.16 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad84041000g300270m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH MEDIUM 27/07/96 06:25:39 0.13E+05 11940 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/84041000.005/ad84041000g300270m.unf
Total Good Bad: Region Time Phase Cut
11940 248 0 11692 0 0
Writing events file
248 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11940 248 0 11692 0 0
in 323.89 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad84041000g300370h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 812 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/84041000.005/ad84041000g300370h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000g300370h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad84041000g300370h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 P1_[NEAR PH HIGH 27/07/96 11:17:55 0.57E+03 812 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/84041000.005/ad84041000g300370h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/84041000.005/
Setting mkf directory to /data/data24/seq_proc/84041000.005/
!earthevents:ASCA > read events ad84041000g300370h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/84041000.005/
HK Directory is: /data/data24/seq_proc/84041000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad84041000g300370h.brt since it contains 0 eventsOffset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad84041000s000102h.unf|S0_LVDL0|155|S0 event discrimination lower level for ccd 0 ad84041000s000202h.unf|S0_LVDL0|198|S0 event discrimination lower level for ccd 0-> listing ad84041000s000102h.unf
ad84041000s000302m.unf|S0_LVDL0|155|S0 event discrimination lower level for ccd 0 ad84041000s000402m.unf|S0_LVDL0|198|S0 event discrimination lower level for ccd 0-> listing ad84041000s000302m.unf
ad84041000s000112h.unf|S0_LVDL0|155|S0 event discrimination lower level for ccd 0 ad84041000s000212h.unf|S0_LVDL0|198|S0 event discrimination lower level for ccd 0-> listing ad84041000s000112h.unf
ad84041000s000312m.unf|S0_LVDL0|155|S0 event discrimination lower level for ccd 0 ad84041000s000412m.unf|S0_LVDL0|198|S0 event discrimination lower level for ccd 0-> listing ad84041000s000312m.unf
ad84041000s000101h.unf|S0_LVENA|0|S0 Level discrimination enable/disable ad84041000s000201h.unf|S0_LVENA|0|S0 Level discrimination enable/disable ad84041000s000701h.unf|S0_LVENA|1|S0 Level discrimination enable/disable ad84041000s000101h.unf|S0_LVDL0|155|S0 event discrimination lower level for ccd 0 ad84041000s000201h.unf|S0_LVDL0|198|S0 event discrimination lower level for ccd 0 ad84041000s000701h.unf|S0_LVDL0|155|S0 event discrimination lower level for ccd 0-> listing ad84041000s000101h.unf
ad84041000s000301m.unf|S0_LVDL0|155|S0 event discrimination lower level for ccd 0 ad84041000s000401m.unf|S0_LVDL0|198|S0 event discrimination lower level for ccd 0-> listing ad84041000s000301m.unf
ad84041000s000501l.unf|S0_LVENA|1|S0 Level discrimination enable/disable ad84041000s000601l.unf|S0_LVENA|0|S0 Level discrimination enable/disable-> listing ad84041000s000501l.unf
ad84041000s100102h.unf|S1_DESTA|0|S1 DE normal/reset ad84041000s100302h.unf|S1_DESTA|1|S1 DE normal/reset-> listing ad84041000s100102h.unf
ad84041000s100112h.unf|S1_DESTA|0|S1 DE normal/reset ad84041000s100312h.unf|S1_DESTA|1|S1 DE normal/reset-> listing ad84041000s100112h.unf
ad84041000s100101h.unf|S1_DESTA|0|S1 DE normal/reset ad84041000s100301h.unf|S1_DESTA|1|S1 DE normal/reset ad84041000s100501h.unf|S1_DESTA|0|S1 DE normal/reset ad84041000s100101h.unf|S1_LVENA|0|S1 Level discrimination enable/disable ad84041000s100301h.unf|S1_LVENA|0|S1 Level discrimination enable/disable ad84041000s100501h.unf|S1_LVENA|1|S1 Level discrimination enable/disable-> listing ad84041000s100101h.unf
ad84041000s100401l.unf|S1_LVENA|1|S1 Level discrimination enable/disable ad84041000s100601l.unf|S1_LVENA|0|S1 Level discrimination enable/disable-> listing ad84041000s100401l.unf
ad84041000g200170h.unf|CPU2|RUN|CPU2 run/stop ad84041000g200370h.unf|CPU2|STOP|CPU2 run/stop ad84041000g200170h.unf|CPU3|RUN|CPU3 run/stop ad84041000g200370h.unf|CPU3|STOP|CPU3 run/stop-> listing ad84041000g200170h.unf
ad84041000g300170h.unf|CPU2|RUN|CPU2 run/stop ad84041000g300370h.unf|CPU2|STOP|CPU2 run/stop ad84041000g300170h.unf|CPU3|RUN|CPU3 run/stop ad84041000g300370h.unf|CPU3|STOP|CPU3 run/stop-> listing ad84041000g300170h.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files