The following information is also available:
Time column is TIME ORDERED-> Fetching fa970214_2351.1240.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 130117901.882400 130164065.738800
Data file start and stop ascatime : 130117901.882400 130164065.738800
Aspecting run start and stop ascatime : 130117901.882525 130164065.738668
Time interval averaged over (seconds) : 46163.856143
Total pointing and manuver time (sec) : 24190.986328 21972.976562
Mean boresight Euler angles : 50.139408 47.656634 202.034373
RA DEC SUN ANGLE
Mean solar position (deg) : 327.86 -12.99
Mean aberration (arcsec) : -1.43 8.05
Mean sat X-axis (deg) : 261.139497 43.246248 82.73
Mean sat Y-axis (deg) : 335.388325 -16.098582 7.92
Mean sat Z-axis (deg) : 50.139408 42.343365 93.13
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 49.892036 42.125980 112.200409 0.087533
Minimum 49.714741 42.021965 105.301979 0.000000
Maximum 49.911510 42.128067 112.209862 10.064760
Sigma (RMS) 0.000326 0.000045 0.033815 0.074075
Number of ASPECT records processed = 40728
Aspecting to RA/DEC : 49.89203644 42.12598038
closing output file...
closing attitude file...
-> Standard Error Output From FTOOL attitudeATTITUDE_V0.9j : Detected gap > 15min in attitude file: 130119021.37901 ATTITUDE_V0.9j : Detected gap > 15min in attitude file:-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 49.892 DEC: 42.126
START TIME: SC 130117901.8825 = UT 14/02/97 23:51:41
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000103 0.849 8603 1 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0
7786.975586 0.125 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
9867.969727 0.083 F880C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 7
13381.958984 0.092 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
15627.951172 0.035 8003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
19125.941406 0.022 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
21339.933594 0.008 8003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
24869.921875 0.025 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
27067.916016 0.054 8003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
30613.904297 0.091 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
32811.898438 0.121 D880C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 3
36357.886719 0.166 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
38603.878906 0.156 F880C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 7
42107.867188 0.187 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
44299.863281 0.183 F880C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 7
46163.855469 10.065 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
Attitude Records: 40728
Attitude Steps: 16
Maneuver ACM time: 21973.0 sec
Pointed ACM time: 24191.0 sec
-> Calculating aspect point83 112 count=1 sum1=49.995 sum2=47.784 sum3=195.114 97 99 count=9499 sum1=476251 sum2=452687 sum3=1.91914e+06 98 99 count=31207 sum1=1.56475e+06 sum2=1.48723e+06 sum3=6.30487e+06 99 99 count=16 sum1=802.433 sum2=762.538 sum3=3232.22 99 100 count=2 sum1=100.314 sum2=95.32 sum3=404.016 100 100 count=2 sum1=100.318 sum2=95.32 sum3=404.014 0 out of 40727 points outside bin structure-> Euler angles: 50.1401, 47.6567, 202.034
Interpolating 701 records in time interval 1.30164e+08 - 1.30164e+08
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft970214_2351.1240",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft970214_2351.1240 Initial mode = 1 (Faint) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 2 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 652032 Bright = 0 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 0 PH = 651008 MPC = 0 PCAL = 0 Memory Check = 1024 Number of superframes = 10204 no. of SIS events found = 780888-> Standard Error Output From FTOOL frfread
coordinate error 12 0 coordinate error 0 0 coordinate error 0 7-> Removing the following files with NEVENTS=0
ft970214_2351_1240G200370H.fits ft970214_2351_1240G200470H.fits ft970214_2351_1240G200599.fits ft970214_2351_1240G200670L.fits ft970214_2351_1240G201470H.fits ft970214_2351_1240G201570H.fits ft970214_2351_1240G201670M.fits ft970214_2351_1240G201770L.fits ft970214_2351_1240G202599.fits ft970214_2351_1240G202770H.fits ft970214_2351_1240G202870H.fits ft970214_2351_1240G202970M.fits ft970214_2351_1240G203070M.fits ft970214_2351_1240G203170H.fits ft970214_2351_1240G203270H.fits ft970214_2351_1240G203370H.fits ft970214_2351_1240G203470H.fits ft970214_2351_1240G203999.fits ft970214_2351_1240G204270H.fits ft970214_2351_1240G204370M.fits ft970214_2351_1240G204470M.fits ft970214_2351_1240G204570H.fits ft970214_2351_1240G204670H.fits ft970214_2351_1240G204770H.fits ft970214_2351_1240G204870H.fits ft970214_2351_1240G205170H.fits ft970214_2351_1240G205399.fits ft970214_2351_1240G205570H.fits ft970214_2351_1240G205670H.fits ft970214_2351_1240G205770M.fits ft970214_2351_1240G205870H.fits ft970214_2351_1240G205970H.fits ft970214_2351_1240G206470H.fits ft970214_2351_1240G206570H.fits ft970214_2351_1240G206670H.fits ft970214_2351_1240G206770H.fits ft970214_2351_1240G207373H.fits ft970214_2351_1240G207770L.fits ft970214_2351_1240G207870M.fits ft970214_2351_1240G208270L.fits ft970214_2351_1240G208370M.fits ft970214_2351_1240G208470M.fits ft970214_2351_1240G208570M.fits ft970214_2351_1240G208670M.fits ft970214_2351_1240G300670H.fits ft970214_2351_1240G300799.fits ft970214_2351_1240G300870L.fits ft970214_2351_1240G301670H.fits ft970214_2351_1240G301770H.fits ft970214_2351_1240G301870M.fits ft970214_2351_1240G301970L.fits ft970214_2351_1240G302799.fits ft970214_2351_1240G302970H.fits ft970214_2351_1240G303070H.fits ft970214_2351_1240G303170M.fits ft970214_2351_1240G303270M.fits ft970214_2351_1240G303370H.fits ft970214_2351_1240G303470H.fits ft970214_2351_1240G303570H.fits ft970214_2351_1240G303670H.fits ft970214_2351_1240G304199.fits ft970214_2351_1240G304370H.fits ft970214_2351_1240G304470H.fits ft970214_2351_1240G304570M.fits ft970214_2351_1240G304670M.fits ft970214_2351_1240G304770H.fits ft970214_2351_1240G304870H.fits ft970214_2351_1240G304970H.fits ft970214_2351_1240G305070H.fits ft970214_2351_1240G305170H.fits ft970214_2351_1240G305370H.fits ft970214_2351_1240G305599.fits ft970214_2351_1240G305770H.fits ft970214_2351_1240G305870H.fits ft970214_2351_1240G305970M.fits ft970214_2351_1240G306070H.fits ft970214_2351_1240G306170H.fits ft970214_2351_1240G306570H.fits ft970214_2351_1240G306870H.fits ft970214_2351_1240G306970H.fits ft970214_2351_1240G307070H.fits ft970214_2351_1240G307170H.fits ft970214_2351_1240G307573H.fits ft970214_2351_1240G307970L.fits ft970214_2351_1240G308070M.fits ft970214_2351_1240G308470L.fits ft970214_2351_1240G308570M.fits ft970214_2351_1240G308670M.fits ft970214_2351_1240G308770M.fits ft970214_2351_1240G308870M.fits ft970214_2351_1240S000601H.fits ft970214_2351_1240S000799.fits ft970214_2351_1240S000801L.fits ft970214_2351_1240S001601M.fits ft970214_2351_1240S001701L.fits ft970214_2351_1240S001801L.fits ft970214_2351_1240S002399.fits ft970214_2351_1240S002601M.fits ft970214_2351_1240S002701M.fits ft970214_2351_1240S002801M.fits ft970214_2351_1240S002901H.fits ft970214_2351_1240S003299.fits ft970214_2351_1240S003501M.fits ft970214_2351_1240S003601M.fits ft970214_2351_1240S003701M.fits ft970214_2351_1240S004299.fits ft970214_2351_1240S004501M.fits ft970214_2351_1240S004601M.fits ft970214_2351_1240S005099.fits ft970214_2351_1240S005401L.fits ft970214_2351_1240S006101L.fits ft970214_2351_1240S006201M.fits ft970214_2351_1240S100601H.fits ft970214_2351_1240S100799.fits ft970214_2351_1240S101401M.fits ft970214_2351_1240S101501L.fits ft970214_2351_1240S101999.fits ft970214_2351_1240S102201M.fits ft970214_2351_1240S102301M.fits ft970214_2351_1240S102401H.fits ft970214_2351_1240S102699.fits ft970214_2351_1240S102901M.fits ft970214_2351_1240S103001M.fits ft970214_2351_1240S103499.fits ft970214_2351_1240S103701M.fits ft970214_2351_1240S104199.fits ft970214_2351_1240S104901L.fits ft970214_2351_1240S105001M.fits-> Checking for empty GTI extensions
ft970214_2351_1240S000101M.fits[3] ft970214_2351_1240S000201H.fits[3] ft970214_2351_1240S000301H.fits[3] ft970214_2351_1240S000401H.fits[3] ft970214_2351_1240S000501H.fits[3] ft970214_2351_1240S000901L.fits[3] ft970214_2351_1240S001001L.fits[3] ft970214_2351_1240S001101M.fits[3] ft970214_2351_1240S001201M.fits[3] ft970214_2351_1240S001301H.fits[3] ft970214_2351_1240S001401H.fits[3] ft970214_2351_1240S001501M.fits[3] ft970214_2351_1240S001901L.fits[3] ft970214_2351_1240S002001M.fits[3] ft970214_2351_1240S002101M.fits[3] ft970214_2351_1240S002201H.fits[3] ft970214_2351_1240S002401H.fits[3] ft970214_2351_1240S002501H.fits[3] ft970214_2351_1240S003001H.fits[3] ft970214_2351_1240S003101H.fits[3] ft970214_2351_1240S003301H.fits[3] ft970214_2351_1240S003401H.fits[3] ft970214_2351_1240S003801M.fits[3] ft970214_2351_1240S003901H.fits[3] ft970214_2351_1240S004001H.fits[3] ft970214_2351_1240S004101H.fits[3] ft970214_2351_1240S004301H.fits[3] ft970214_2351_1240S004401M.fits[3] ft970214_2351_1240S004701M.fits[3] ft970214_2351_1240S004801H.fits[3] ft970214_2351_1240S004901H.fits[3] ft970214_2351_1240S005101H.fits[3] ft970214_2351_1240S005201M.fits[3] ft970214_2351_1240S005301L.fits[3] ft970214_2351_1240S005501L.fits[3] ft970214_2351_1240S005601L.fits[3] ft970214_2351_1240S005701M.fits[3] ft970214_2351_1240S005801M.fits[3] ft970214_2351_1240S005901L.fits[3] ft970214_2351_1240S006001L.fits[3] ft970214_2351_1240S006301M.fits[3]-> Merging GTIs from the following files:
ft970214_2351_1240S100101M.fits[3] ft970214_2351_1240S100201H.fits[3] ft970214_2351_1240S100301H.fits[3] ft970214_2351_1240S100401H.fits[3] ft970214_2351_1240S100501H.fits[3] ft970214_2351_1240S100801L.fits[3] ft970214_2351_1240S100901L.fits[3] ft970214_2351_1240S101001M.fits[3] ft970214_2351_1240S101101H.fits[3] ft970214_2351_1240S101201H.fits[3] ft970214_2351_1240S101301M.fits[3] ft970214_2351_1240S101601L.fits[3] ft970214_2351_1240S101701M.fits[3] ft970214_2351_1240S101801H.fits[3] ft970214_2351_1240S102001H.fits[3] ft970214_2351_1240S102101H.fits[3] ft970214_2351_1240S102501H.fits[3] ft970214_2351_1240S102701H.fits[3] ft970214_2351_1240S102801H.fits[3] ft970214_2351_1240S103101M.fits[3] ft970214_2351_1240S103201H.fits[3] ft970214_2351_1240S103301H.fits[3] ft970214_2351_1240S103501H.fits[3] ft970214_2351_1240S103601M.fits[3] ft970214_2351_1240S103801M.fits[3] ft970214_2351_1240S103901H.fits[3] ft970214_2351_1240S104001H.fits[3] ft970214_2351_1240S104201H.fits[3] ft970214_2351_1240S104301M.fits[3] ft970214_2351_1240S104401L.fits[3] ft970214_2351_1240S104501L.fits[3] ft970214_2351_1240S104601L.fits[3] ft970214_2351_1240S104701M.fits[3] ft970214_2351_1240S104801L.fits[3] ft970214_2351_1240S105101M.fits[3]-> Merging GTIs from the following files:
ft970214_2351_1240G200170M.fits[3] ft970214_2351_1240G200270H.fits[3] ft970214_2351_1240G200770L.fits[3] ft970214_2351_1240G200870L.fits[3] ft970214_2351_1240G200970M.fits[3] ft970214_2351_1240G201070M.fits[3] ft970214_2351_1240G201170M.fits[3] ft970214_2351_1240G201270M.fits[3] ft970214_2351_1240G201370H.fits[3] ft970214_2351_1240G201870L.fits[3] ft970214_2351_1240G201970L.fits[3] ft970214_2351_1240G202070M.fits[3] ft970214_2351_1240G202170M.fits[3] ft970214_2351_1240G202270M.fits[3] ft970214_2351_1240G202370M.fits[3] ft970214_2351_1240G202470H.fits[3] ft970214_2351_1240G202670H.fits[3] ft970214_2351_1240G203570H.fits[3] ft970214_2351_1240G203670H.fits[3] ft970214_2351_1240G203770H.fits[3] ft970214_2351_1240G203870H.fits[3] ft970214_2351_1240G204070H.fits[3] ft970214_2351_1240G204170H.fits[3] ft970214_2351_1240G204970H.fits[3] ft970214_2351_1240G205070H.fits[3] ft970214_2351_1240G205270H.fits[3] ft970214_2351_1240G205470H.fits[3] ft970214_2351_1240G206070H.fits[3] ft970214_2351_1240G206170H.fits[3] ft970214_2351_1240G206270H.fits[3] ft970214_2351_1240G206370H.fits[3] ft970214_2351_1240G206870H.fits[3] ft970214_2351_1240G206970H.fits[3] ft970214_2351_1240G207070H.fits[3] ft970214_2351_1240G207170H.fits[3] ft970214_2351_1240G207270H.fits[3] ft970214_2351_1240G207470H.fits[3] ft970214_2351_1240G207570M.fits[3] ft970214_2351_1240G207670L.fits[3] ft970214_2351_1240G207970M.fits[3] ft970214_2351_1240G208070M.fits[3] ft970214_2351_1240G208170L.fits[3]-> Merging GTIs from the following files:
ft970214_2351_1240G300170M.fits[3] ft970214_2351_1240G300270H.fits[3] ft970214_2351_1240G300370H.fits[3] ft970214_2351_1240G300470H.fits[3] ft970214_2351_1240G300570H.fits[3] ft970214_2351_1240G300970L.fits[3] ft970214_2351_1240G301070L.fits[3] ft970214_2351_1240G301170M.fits[3] ft970214_2351_1240G301270M.fits[3] ft970214_2351_1240G301370M.fits[3] ft970214_2351_1240G301470M.fits[3] ft970214_2351_1240G301570H.fits[3] ft970214_2351_1240G302070L.fits[3] ft970214_2351_1240G302170L.fits[3] ft970214_2351_1240G302270M.fits[3] ft970214_2351_1240G302370M.fits[3] ft970214_2351_1240G302470M.fits[3] ft970214_2351_1240G302570M.fits[3] ft970214_2351_1240G302670H.fits[3] ft970214_2351_1240G302870H.fits[3] ft970214_2351_1240G303770H.fits[3] ft970214_2351_1240G303870H.fits[3] ft970214_2351_1240G303970H.fits[3] ft970214_2351_1240G304070H.fits[3] ft970214_2351_1240G304270H.fits[3] ft970214_2351_1240G305270H.fits[3] ft970214_2351_1240G305470H.fits[3] ft970214_2351_1240G305670H.fits[3] ft970214_2351_1240G306270H.fits[3] ft970214_2351_1240G306370H.fits[3] ft970214_2351_1240G306470H.fits[3] ft970214_2351_1240G306670H.fits[3] ft970214_2351_1240G306770H.fits[3] ft970214_2351_1240G307270H.fits[3] ft970214_2351_1240G307370H.fits[3] ft970214_2351_1240G307470H.fits[3] ft970214_2351_1240G307670H.fits[3] ft970214_2351_1240G307770M.fits[3] ft970214_2351_1240G307870L.fits[3] ft970214_2351_1240G308170M.fits[3] ft970214_2351_1240G308270M.fits[3] ft970214_2351_1240G308370L.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g200370h.prelist merge count = 2 photon cnt = 2 GISSORTSPLIT:LO:g200470h.prelist merge count = 3 photon cnt = 4 GISSORTSPLIT:LO:g200570h.prelist merge count = 2 photon cnt = 3 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g200770h.prelist merge count = 10 photon cnt = 37626 GISSORTSPLIT:LO:g200870h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 25 GISSORTSPLIT:LO:g201070h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g201170h.prelist merge count = 1 photon cnt = 1255 GISSORTSPLIT:LO:g200170l.prelist merge count = 2 photon cnt = 8 GISSORTSPLIT:LO:g200270l.prelist merge count = 4 photon cnt = 2258 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 36 GISSORTSPLIT:LO:g200270m.prelist merge count = 5 photon cnt = 13711 GISSORTSPLIT:LO:g200370m.prelist merge count = 2 photon cnt = 74 GISSORTSPLIT:LO:g200470m.prelist merge count = 1 photon cnt = 26 GISSORTSPLIT:LO:g200570m.prelist merge count = 1 photon cnt = 33 GISSORTSPLIT:LO:g200670m.prelist merge count = 1 photon cnt = 41 GISSORTSPLIT:LO:g200770m.prelist merge count = 1 photon cnt = 25 GISSORTSPLIT:LO:Total filenames split = 42 GISSORTSPLIT:LO:Total split file cnt = 20 GISSORTSPLIT:LO:End program-> Creating ad85001000g200170h.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240G200270H.fits 2 -- ft970214_2351_1240G201370H.fits 3 -- ft970214_2351_1240G202470H.fits 4 -- ft970214_2351_1240G202670H.fits 5 -- ft970214_2351_1240G203870H.fits 6 -- ft970214_2351_1240G204070H.fits 7 -- ft970214_2351_1240G205270H.fits 8 -- ft970214_2351_1240G205470H.fits 9 -- ft970214_2351_1240G206270H.fits 10 -- ft970214_2351_1240G207270H.fits Merging binary extension #: 2 1 -- ft970214_2351_1240G200270H.fits 2 -- ft970214_2351_1240G201370H.fits 3 -- ft970214_2351_1240G202470H.fits 4 -- ft970214_2351_1240G202670H.fits 5 -- ft970214_2351_1240G203870H.fits 6 -- ft970214_2351_1240G204070H.fits 7 -- ft970214_2351_1240G205270H.fits 8 -- ft970214_2351_1240G205470H.fits 9 -- ft970214_2351_1240G206270H.fits 10 -- ft970214_2351_1240G207270H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad85001000g200270m.unf
---- cmerge: version 1.5 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240G200170M.fits 2 -- ft970214_2351_1240G201270M.fits 3 -- ft970214_2351_1240G202370M.fits 4 -- ft970214_2351_1240G207570M.fits 5 -- ft970214_2351_1240G208070M.fits Merging binary extension #: 2 1 -- ft970214_2351_1240G200170M.fits 2 -- ft970214_2351_1240G201270M.fits 3 -- ft970214_2351_1240G202370M.fits 4 -- ft970214_2351_1240G207570M.fits 5 -- ft970214_2351_1240G208070M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad85001000g200370l.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240G200870L.fits 2 -- ft970214_2351_1240G201970L.fits 3 -- ft970214_2351_1240G207670L.fits 4 -- ft970214_2351_1240G208170L.fits Merging binary extension #: 2 1 -- ft970214_2351_1240G200870L.fits 2 -- ft970214_2351_1240G201970L.fits 3 -- ft970214_2351_1240G207670L.fits 4 -- ft970214_2351_1240G208170L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft970214_2351_1240G207470H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240G207470H.fits Merging binary extension #: 2 1 -- ft970214_2351_1240G207470H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000074 events
ft970214_2351_1240G201170M.fits ft970214_2351_1240G202270M.fits-> Ignoring the following files containing 000000041 events
ft970214_2351_1240G202070M.fits-> Ignoring the following files containing 000000036 events
ft970214_2351_1240G207970M.fits-> Ignoring the following files containing 000000033 events
ft970214_2351_1240G201070M.fits-> Ignoring the following files containing 000000026 events
ft970214_2351_1240G200970M.fits-> Ignoring the following files containing 000000025 events
ft970214_2351_1240G207070H.fits-> Ignoring the following files containing 000000025 events
ft970214_2351_1240G202170M.fits-> Ignoring the following files containing 000000008 events
ft970214_2351_1240G200770L.fits ft970214_2351_1240G201870L.fits-> Ignoring the following files containing 000000006 events
ft970214_2351_1240G207170H.fits-> Ignoring the following files containing 000000005 events
ft970214_2351_1240G206970H.fits-> Ignoring the following files containing 000000005 events
ft970214_2351_1240G206370H.fits-> Ignoring the following files containing 000000004 events
ft970214_2351_1240G203670H.fits ft970214_2351_1240G205070H.fits ft970214_2351_1240G206070H.fits-> Ignoring the following files containing 000000003 events
ft970214_2351_1240G203770H.fits ft970214_2351_1240G206170H.fits-> Ignoring the following files containing 000000002 events
ft970214_2351_1240G203570H.fits ft970214_2351_1240G204970H.fits-> Ignoring the following files containing 000000002 events
ft970214_2351_1240G206870H.fits-> Ignoring the following files containing 000000001 events
ft970214_2351_1240G204170H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300470h.prelist merge count = 3 photon cnt = 7 GISSORTSPLIT:LO:g300570h.prelist merge count = 2 photon cnt = 9 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 13 GISSORTSPLIT:LO:g300870h.prelist merge count = 11 photon cnt = 34721 GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g301070h.prelist merge count = 1 photon cnt = 40 GISSORTSPLIT:LO:g301170h.prelist merge count = 1 photon cnt = 1165 GISSORTSPLIT:LO:g300170l.prelist merge count = 2 photon cnt = 2 GISSORTSPLIT:LO:g300270l.prelist merge count = 4 photon cnt = 1995 GISSORTSPLIT:LO:g300170m.prelist merge count = 1 photon cnt = 29 GISSORTSPLIT:LO:g300270m.prelist merge count = 5 photon cnt = 12681 GISSORTSPLIT:LO:g300370m.prelist merge count = 2 photon cnt = 74 GISSORTSPLIT:LO:g300470m.prelist merge count = 1 photon cnt = 12 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 27 GISSORTSPLIT:LO:g300670m.prelist merge count = 1 photon cnt = 36 GISSORTSPLIT:LO:g300770m.prelist merge count = 1 photon cnt = 31 GISSORTSPLIT:LO:Total filenames split = 42 GISSORTSPLIT:LO:Total split file cnt = 20 GISSORTSPLIT:LO:End program-> Creating ad85001000g300170h.unf
---- cmerge: version 1.5 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240G300270H.fits 2 -- ft970214_2351_1240G300470H.fits 3 -- ft970214_2351_1240G301570H.fits 4 -- ft970214_2351_1240G302670H.fits 5 -- ft970214_2351_1240G302870H.fits 6 -- ft970214_2351_1240G304070H.fits 7 -- ft970214_2351_1240G304270H.fits 8 -- ft970214_2351_1240G305470H.fits 9 -- ft970214_2351_1240G305670H.fits 10 -- ft970214_2351_1240G306470H.fits 11 -- ft970214_2351_1240G307470H.fits Merging binary extension #: 2 1 -- ft970214_2351_1240G300270H.fits 2 -- ft970214_2351_1240G300470H.fits 3 -- ft970214_2351_1240G301570H.fits 4 -- ft970214_2351_1240G302670H.fits 5 -- ft970214_2351_1240G302870H.fits 6 -- ft970214_2351_1240G304070H.fits 7 -- ft970214_2351_1240G304270H.fits 8 -- ft970214_2351_1240G305470H.fits 9 -- ft970214_2351_1240G305670H.fits 10 -- ft970214_2351_1240G306470H.fits 11 -- ft970214_2351_1240G307470H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad85001000g300270m.unf
---- cmerge: version 1.5 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240G300170M.fits 2 -- ft970214_2351_1240G301470M.fits 3 -- ft970214_2351_1240G302570M.fits 4 -- ft970214_2351_1240G307770M.fits 5 -- ft970214_2351_1240G308270M.fits Merging binary extension #: 2 1 -- ft970214_2351_1240G300170M.fits 2 -- ft970214_2351_1240G301470M.fits 3 -- ft970214_2351_1240G302570M.fits 4 -- ft970214_2351_1240G307770M.fits 5 -- ft970214_2351_1240G308270M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad85001000g300370l.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240G301070L.fits 2 -- ft970214_2351_1240G302170L.fits 3 -- ft970214_2351_1240G307870L.fits 4 -- ft970214_2351_1240G308370L.fits Merging binary extension #: 2 1 -- ft970214_2351_1240G301070L.fits 2 -- ft970214_2351_1240G302170L.fits 3 -- ft970214_2351_1240G307870L.fits 4 -- ft970214_2351_1240G308370L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft970214_2351_1240G307670H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240G307670H.fits Merging binary extension #: 2 1 -- ft970214_2351_1240G307670H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000074 events
ft970214_2351_1240G301370M.fits ft970214_2351_1240G302470M.fits-> Ignoring the following files containing 000000040 events
ft970214_2351_1240G306670H.fits-> Ignoring the following files containing 000000036 events
ft970214_2351_1240G302270M.fits-> Ignoring the following files containing 000000031 events
ft970214_2351_1240G302370M.fits-> Ignoring the following files containing 000000029 events
ft970214_2351_1240G308170M.fits-> Ignoring the following files containing 000000027 events
ft970214_2351_1240G301270M.fits-> Ignoring the following files containing 000000013 events
ft970214_2351_1240G300370H.fits-> Ignoring the following files containing 000000012 events
ft970214_2351_1240G301170M.fits-> Ignoring the following files containing 000000009 events
ft970214_2351_1240G303970H.fits ft970214_2351_1240G306370H.fits-> Ignoring the following files containing 000000007 events
ft970214_2351_1240G303870H.fits ft970214_2351_1240G305270H.fits ft970214_2351_1240G306270H.fits-> Ignoring the following files containing 000000004 events
ft970214_2351_1240G307370H.fits-> Ignoring the following files containing 000000003 events
ft970214_2351_1240G306770H.fits-> Ignoring the following files containing 000000002 events
ft970214_2351_1240G300970L.fits ft970214_2351_1240G302070L.fits-> Ignoring the following files containing 000000002 events
ft970214_2351_1240G307270H.fits-> Ignoring the following files containing 000000001 events
ft970214_2351_1240G303770H.fits-> Ignoring the following files containing 000000001 events
ft970214_2351_1240G300570H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 11 photon cnt = 204332 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 1 photon cnt = 33 SIS0SORTSPLIT:LO:s000301h.prelist merge count = 1 photon cnt = 46 SIS0SORTSPLIT:LO:s000401h.prelist merge count = 3 photon cnt = 90036 SIS0SORTSPLIT:LO:s000501h.prelist merge count = 1 photon cnt = 256 SIS0SORTSPLIT:LO:s000601h.prelist merge count = 3 photon cnt = 768 SIS0SORTSPLIT:LO:s000701l.prelist merge count = 2 photon cnt = 2891 SIS0SORTSPLIT:LO:s000801l.prelist merge count = 4 photon cnt = 4030 SIS0SORTSPLIT:LO:s000901l.prelist merge count = 2 photon cnt = 96 SIS0SORTSPLIT:LO:s001001m.prelist merge count = 6 photon cnt = 12543 SIS0SORTSPLIT:LO:s001101m.prelist merge count = 7 photon cnt = 8452 SIS0SORTSPLIT:LO:Total filenames split = 41 SIS0SORTSPLIT:LO:Total split file cnt = 11 SIS0SORTSPLIT:LO:End program-> Creating ad85001000s000101h.unf
---- cmerge: version 1.5 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240S000201H.fits 2 -- ft970214_2351_1240S000401H.fits 3 -- ft970214_2351_1240S001301H.fits 4 -- ft970214_2351_1240S002201H.fits 5 -- ft970214_2351_1240S002401H.fits 6 -- ft970214_2351_1240S003101H.fits 7 -- ft970214_2351_1240S003301H.fits 8 -- ft970214_2351_1240S004101H.fits 9 -- ft970214_2351_1240S004301H.fits 10 -- ft970214_2351_1240S004901H.fits 11 -- ft970214_2351_1240S005101H.fits Merging binary extension #: 2 1 -- ft970214_2351_1240S000201H.fits 2 -- ft970214_2351_1240S000401H.fits 3 -- ft970214_2351_1240S001301H.fits 4 -- ft970214_2351_1240S002201H.fits 5 -- ft970214_2351_1240S002401H.fits 6 -- ft970214_2351_1240S003101H.fits 7 -- ft970214_2351_1240S003301H.fits 8 -- ft970214_2351_1240S004101H.fits 9 -- ft970214_2351_1240S004301H.fits 10 -- ft970214_2351_1240S004901H.fits 11 -- ft970214_2351_1240S005101H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad85001000s000201h.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240S003001H.fits 2 -- ft970214_2351_1240S004001H.fits 3 -- ft970214_2351_1240S004801H.fits Merging binary extension #: 2 1 -- ft970214_2351_1240S003001H.fits 2 -- ft970214_2351_1240S004001H.fits 3 -- ft970214_2351_1240S004801H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad85001000s000301m.unf
---- cmerge: version 1.5 ---- A total of 6 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240S001201M.fits 2 -- ft970214_2351_1240S001501M.fits 3 -- ft970214_2351_1240S002101M.fits 4 -- ft970214_2351_1240S004401M.fits 5 -- ft970214_2351_1240S005201M.fits 6 -- ft970214_2351_1240S005801M.fits Merging binary extension #: 2 1 -- ft970214_2351_1240S001201M.fits 2 -- ft970214_2351_1240S001501M.fits 3 -- ft970214_2351_1240S002101M.fits 4 -- ft970214_2351_1240S004401M.fits 5 -- ft970214_2351_1240S005201M.fits 6 -- ft970214_2351_1240S005801M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad85001000s000401m.unf
---- cmerge: version 1.5 ---- A total of 7 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240S000101M.fits 2 -- ft970214_2351_1240S001101M.fits 3 -- ft970214_2351_1240S002001M.fits 4 -- ft970214_2351_1240S003801M.fits 5 -- ft970214_2351_1240S004701M.fits 6 -- ft970214_2351_1240S005701M.fits 7 -- ft970214_2351_1240S006301M.fits Merging binary extension #: 2 1 -- ft970214_2351_1240S000101M.fits 2 -- ft970214_2351_1240S001101M.fits 3 -- ft970214_2351_1240S002001M.fits 4 -- ft970214_2351_1240S003801M.fits 5 -- ft970214_2351_1240S004701M.fits 6 -- ft970214_2351_1240S005701M.fits 7 -- ft970214_2351_1240S006301M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad85001000s000501l.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240S001001L.fits 2 -- ft970214_2351_1240S001901L.fits 3 -- ft970214_2351_1240S005601L.fits 4 -- ft970214_2351_1240S006001L.fits Merging binary extension #: 2 1 -- ft970214_2351_1240S001001L.fits 2 -- ft970214_2351_1240S001901L.fits 3 -- ft970214_2351_1240S005601L.fits 4 -- ft970214_2351_1240S006001L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad85001000s000601l.unf
---- cmerge: version 1.5 ---- A total of 2 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240S005301L.fits 2 -- ft970214_2351_1240S005901L.fits Merging binary extension #: 2 1 -- ft970214_2351_1240S005301L.fits 2 -- ft970214_2351_1240S005901L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000768 events
ft970214_2351_1240S000501H.fits ft970214_2351_1240S002501H.fits ft970214_2351_1240S003401H.fits-> Ignoring the following files containing 000000256 events
ft970214_2351_1240S003901H.fits-> Ignoring the following files containing 000000096 events
ft970214_2351_1240S000901L.fits ft970214_2351_1240S005501L.fits-> Ignoring the following files containing 000000046 events
ft970214_2351_1240S001401H.fits-> Ignoring the following files containing 000000033 events
ft970214_2351_1240S000301H.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 1 photon cnt = 87 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 11 photon cnt = 416224 SIS1SORTSPLIT:LO:s100301h.prelist merge count = 3 photon cnt = 591 SIS1SORTSPLIT:LO:s100401h.prelist merge count = 3 photon cnt = 768 SIS1SORTSPLIT:LO:s100501l.prelist merge count = 5 photon cnt = 7877 SIS1SORTSPLIT:LO:s100601l.prelist merge count = 2 photon cnt = 96 SIS1SORTSPLIT:LO:s100701m.prelist merge count = 10 photon cnt = 31759 SIS1SORTSPLIT:LO:Total filenames split = 35 SIS1SORTSPLIT:LO:Total split file cnt = 7 SIS1SORTSPLIT:LO:End program-> Creating ad85001000s100101h.unf
---- cmerge: version 1.5 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240S100201H.fits 2 -- ft970214_2351_1240S100401H.fits 3 -- ft970214_2351_1240S101101H.fits 4 -- ft970214_2351_1240S101801H.fits 5 -- ft970214_2351_1240S102001H.fits 6 -- ft970214_2351_1240S102501H.fits 7 -- ft970214_2351_1240S102701H.fits 8 -- ft970214_2351_1240S103301H.fits 9 -- ft970214_2351_1240S103501H.fits 10 -- ft970214_2351_1240S104001H.fits 11 -- ft970214_2351_1240S104201H.fits Merging binary extension #: 2 1 -- ft970214_2351_1240S100201H.fits 2 -- ft970214_2351_1240S100401H.fits 3 -- ft970214_2351_1240S101101H.fits 4 -- ft970214_2351_1240S101801H.fits 5 -- ft970214_2351_1240S102001H.fits 6 -- ft970214_2351_1240S102501H.fits 7 -- ft970214_2351_1240S102701H.fits 8 -- ft970214_2351_1240S103301H.fits 9 -- ft970214_2351_1240S103501H.fits 10 -- ft970214_2351_1240S104001H.fits 11 -- ft970214_2351_1240S104201H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad85001000s100201m.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240S100101M.fits 2 -- ft970214_2351_1240S101001M.fits 3 -- ft970214_2351_1240S101301M.fits 4 -- ft970214_2351_1240S101701M.fits 5 -- ft970214_2351_1240S103101M.fits 6 -- ft970214_2351_1240S103601M.fits 7 -- ft970214_2351_1240S103801M.fits 8 -- ft970214_2351_1240S104301M.fits 9 -- ft970214_2351_1240S104701M.fits 10 -- ft970214_2351_1240S105101M.fits Merging binary extension #: 2 1 -- ft970214_2351_1240S100101M.fits 2 -- ft970214_2351_1240S101001M.fits 3 -- ft970214_2351_1240S101301M.fits 4 -- ft970214_2351_1240S101701M.fits 5 -- ft970214_2351_1240S103101M.fits 6 -- ft970214_2351_1240S103601M.fits 7 -- ft970214_2351_1240S103801M.fits 8 -- ft970214_2351_1240S104301M.fits 9 -- ft970214_2351_1240S104701M.fits 10 -- ft970214_2351_1240S105101M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad85001000s100301l.unf
---- cmerge: version 1.5 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970214_2351_1240S100901L.fits 2 -- ft970214_2351_1240S101601L.fits 3 -- ft970214_2351_1240S104401L.fits 4 -- ft970214_2351_1240S104601L.fits 5 -- ft970214_2351_1240S104801L.fits Merging binary extension #: 2 1 -- ft970214_2351_1240S100901L.fits 2 -- ft970214_2351_1240S101601L.fits 3 -- ft970214_2351_1240S104401L.fits 4 -- ft970214_2351_1240S104601L.fits 5 -- ft970214_2351_1240S104801L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000768 events
ft970214_2351_1240S100501H.fits ft970214_2351_1240S102101H.fits ft970214_2351_1240S102801H.fits-> Ignoring the following files containing 000000591 events
ft970214_2351_1240S101201H.fits ft970214_2351_1240S103201H.fits ft970214_2351_1240S103901H.fits-> Ignoring the following files containing 000000096 events
ft970214_2351_1240S100801L.fits ft970214_2351_1240S104501L.fits-> Ignoring the following files containing 000000087 events
ft970214_2351_1240S100301H.fits-> Tar-ing together the leftover raw files
a ft970214_2351_1240G200770L.fits 40K a ft970214_2351_1240G200970M.fits 40K a ft970214_2351_1240G201070M.fits 40K a ft970214_2351_1240G201170M.fits 40K a ft970214_2351_1240G201870L.fits 40K a ft970214_2351_1240G202070M.fits 40K a ft970214_2351_1240G202170M.fits 40K a ft970214_2351_1240G202270M.fits 40K a ft970214_2351_1240G203570H.fits 40K a ft970214_2351_1240G203670H.fits 40K a ft970214_2351_1240G203770H.fits 40K a ft970214_2351_1240G204170H.fits 40K a ft970214_2351_1240G204970H.fits 40K a ft970214_2351_1240G205070H.fits 40K a ft970214_2351_1240G206070H.fits 40K a ft970214_2351_1240G206170H.fits 40K a ft970214_2351_1240G206370H.fits 40K a ft970214_2351_1240G206870H.fits 40K a ft970214_2351_1240G206970H.fits 40K a ft970214_2351_1240G207070H.fits 40K a ft970214_2351_1240G207170H.fits 40K a ft970214_2351_1240G207970M.fits 40K a ft970214_2351_1240G300370H.fits 40K a ft970214_2351_1240G300570H.fits 40K a ft970214_2351_1240G300970L.fits 40K a ft970214_2351_1240G301170M.fits 40K a ft970214_2351_1240G301270M.fits 40K a ft970214_2351_1240G301370M.fits 40K a ft970214_2351_1240G302070L.fits 40K a ft970214_2351_1240G302270M.fits 40K a ft970214_2351_1240G302370M.fits 40K a ft970214_2351_1240G302470M.fits 40K a ft970214_2351_1240G303770H.fits 40K a ft970214_2351_1240G303870H.fits 40K a ft970214_2351_1240G303970H.fits 40K a ft970214_2351_1240G305270H.fits 40K a ft970214_2351_1240G306270H.fits 40K a ft970214_2351_1240G306370H.fits 40K a ft970214_2351_1240G306670H.fits 40K a ft970214_2351_1240G306770H.fits 40K a ft970214_2351_1240G307270H.fits 40K a ft970214_2351_1240G307370H.fits 40K a ft970214_2351_1240G308170M.fits 40K a ft970214_2351_1240S000301H.fits 40K a ft970214_2351_1240S000501H.fits 48K a ft970214_2351_1240S000901L.fits 43K a ft970214_2351_1240S001401H.fits 40K a ft970214_2351_1240S002501H.fits 48K a ft970214_2351_1240S003401H.fits 48K a ft970214_2351_1240S003901H.fits 48K a ft970214_2351_1240S005501L.fits 40K a ft970214_2351_1240S100301H.fits 43K a ft970214_2351_1240S100501H.fits 48K a ft970214_2351_1240S100801L.fits 43K a ft970214_2351_1240S101201H.fits 43K a ft970214_2351_1240S102101H.fits 48K a ft970214_2351_1240S102801H.fits 48K a ft970214_2351_1240S103201H.fits 48K a ft970214_2351_1240S103901H.fits 48K a ft970214_2351_1240S104501L.fits 40K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft970214_2351.1240 'ft970214_2351.1240' is successfully opened Data Start Time is 130117898.88 (970214 235138) Time Margin 2.0 sec included Sync error detected in 5169 th SF 'ft970214_2351.1240' EOF detected, sf=10204 Data End Time is 130164046.74 (970215 124046) Gain History is written in ft970214_2351_1240.ghf-> Checking if column CAL_START in ft970214_2351_1240.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft970214_2351_1240.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000g200270m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000g200370l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000g200470h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000g300170h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000g300270m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000g300370l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000g300470h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000s000201h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000s000202h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000s000212h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000s000301m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000s000302m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000s000312m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000s000401m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000s000402m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000s000412m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000s000501l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000s000601l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000s100201m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000s100202m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000s100212m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 130119021.37901 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad85001000s100301l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000s100302l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad85001000s100312l.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 97/ 2/14 23:51 mjd=50493.993750 Orbit file name is ./frf.orbit.215 Epoch of Orbital Elements: 1997/2/10 14:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa970214_2351.1240 S0-HK file: ft970214_2351_1240S0HK.fits S1-HK file: ft970214_2351_1240S1HK.fits G2-HK file: ft970214_2351_1240G2HK.fits G3-HK file: ft970214_2351_1240G3HK.fits output FITS File: ft970214_2351_1240.mkf Total 1444 Data bins were processed.-> Checking if column TIME in ft970214_2351_1240.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 8755.7961 The mean of the selected column is 21.726541 The standard deviation of the selected column is 13.405542 The minimum of selected column is 3.5500145 The maximum of selected column is 186.78181 The number of points used in calculation is 403-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 9982.5451 The mean of the selected column is 24.832202 The standard deviation of the selected column is 16.650796 The minimum of selected column is 4.5902920 The maximum of selected column is 247.12575 The number of points used in calculation is 402-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<61.9 )&& (S0_PIXL2>0.0 && S0_PIXL2<74.7 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:54:28 0.16E+05 129416 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
120907 104168 0 16739 0 0
Writing events file
104168 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
120907 104168 0 16739 0 0
in 13761.95 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 104168
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 56 52006
Flickering pixels iter, pixels & cnts : 1 22 803
cleaning chip # 2
Hot pixels & counts : 40 45292
Flickering pixels iter, pixels & cnts : 1 33 1038
cleaning chip # 3
Number of pixels rejected : 151
Number of (internal) image counts : 104168
Number of image cts rejected (N, %) : 99139 95.1722183
By chip : 0 1 2 3
Pixels rejected : 0 78 73 0
Image counts : 0 54664 49504 0
Image cts rejected: 0 52809 46330 0
Image cts rej (%) : 0.00 96.61 93.59 0.00
filtering data...
Total counts : 0 54664 49504 0
Total cts rejected: 0 52809 46330 0
Total cts rej (%) : 0.00 96.61 93.59 0.00
Number of clean counts accepted : 5029
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 151
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad85001000s000102h.evt use_events=no
Wrote cleaned events file to ad85001000s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad85001000s000112h.unf into ad85001000s000112h.evtThe sum of the selected column is 8755.7961 The mean of the selected column is 21.726541 The standard deviation of the selected column is 13.405542 The minimum of selected column is 3.5500145 The maximum of selected column is 186.78181 The number of points used in calculation is 403-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 9982.5451 The mean of the selected column is 24.832202 The standard deviation of the selected column is 16.650796 The minimum of selected column is 4.5902920 The maximum of selected column is 247.12575 The number of points used in calculation is 402-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<61.9 )&& (S0_PIXL2>0.0 && S0_PIXL2<74.7 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT2 HIGH 14/02/97 23:54:28 0.16E+05 130157 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
122021 105049 0 16972 0 0
Writing events file
105049 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
122021 105049 0 16972 0 0
in 13761.95 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 105049
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 56 52284
Flickering pixels iter, pixels & cnts : 1 22 805
cleaning chip # 2
Hot pixels & counts : 40 45636
Flickering pixels iter, pixels & cnts : 1 34 1061
cleaning chip # 3
Number of pixels rejected : 152
Number of (internal) image counts : 105049
Number of image cts rejected (N, %) : 99786 94.9899597
By chip : 0 1 2 3
Pixels rejected : 0 78 74 0
Image counts : 0 55047 50002 0
Image cts rejected: 0 53089 46697 0
Image cts rej (%) : 0.00 96.44 93.39 0.00
filtering data...
Total counts : 0 55047 50002 0
Total cts rejected: 0 53089 46697 0
Total cts rej (%) : 0.00 96.44 93.39 0.00
Number of clean counts accepted : 5263
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 152
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad85001000s000112h.evt use_events=no
Wrote cleaned events file to ad85001000s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad85001000s000201h.unf because of modeThe sum of the selected column is 115.96912 The mean of the selected column is 16.567016 The standard deviation of the selected column is 3.2092108 The minimum of selected column is 12.812540 The maximum of selected column is 21.531319 The number of points used in calculation is 7-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 142.53170 The mean of the selected column is 20.361671 The standard deviation of the selected column is 8.2575564 The minimum of selected column is 10.062531 The maximum of selected column is 32.437603 The number of points used in calculation is 7-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>6.9 && S0_PIXL1<26.1 )&& (S0_PIXL2>0.0 && S0_PIXL2<45.1 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT HIGH 15/02/97 06:02:48 0.20E+04 11677 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s000202h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
9769 1672 0 8097 0 0
Writing events file
1672 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9769 1672 0 8097 0 0
in 225.64 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 1672
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 38 763
Flickering pixels iter, pixels & cnts : 1 16 89
cleaning chip # 2
Hot pixels & counts : 32 660
Flickering pixels iter, pixels & cnts : 1 12 54
cleaning chip # 3
Number of pixels rejected : 98
Number of (internal) image counts : 1672
Number of image cts rejected (N, %) : 1566 93.6602859
By chip : 0 1 2 3
Pixels rejected : 0 54 44 0
Image counts : 0 901 771 0
Image cts rejected: 0 852 714 0
Image cts rej (%) : 0.00 94.56 92.61 0.00
filtering data...
Total counts : 0 901 771 0
Total cts rejected: 0 852 714 0
Total cts rej (%) : 0.00 94.56 92.61 0.00
Number of clean counts accepted : 106
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 98
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad85001000s000202h.evt use_events=no
Wrote cleaned events file to ad85001000s000202h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad85001000s000212h.unf into ad85001000s000212h.evtThe sum of the selected column is 115.96912 The mean of the selected column is 16.567016 The standard deviation of the selected column is 3.2092108 The minimum of selected column is 12.812540 The maximum of selected column is 21.531319 The number of points used in calculation is 7-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 142.53170 The mean of the selected column is 20.361671 The standard deviation of the selected column is 8.2575564 The minimum of selected column is 10.062531 The maximum of selected column is 32.437603 The number of points used in calculation is 7-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>6.9 && S0_PIXL1<26.1 )&& (S0_PIXL2>0.0 && S0_PIXL2<45.1 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT2 HIGH 15/02/97 06:02:48 0.20E+04 11831 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s000212h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
9947 1692 0 8255 0 0
Writing events file
1692 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9947 1692 0 8255 0 0
in 225.64 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 1692
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 38 768
Flickering pixels iter, pixels & cnts : 1 16 91
cleaning chip # 2
Hot pixels & counts : 32 667
Flickering pixels iter, pixels & cnts : 1 12 55
cleaning chip # 3
Number of pixels rejected : 98
Number of (internal) image counts : 1692
Number of image cts rejected (N, %) : 1581 93.4397125
By chip : 0 1 2 3
Pixels rejected : 0 54 44 0
Image counts : 0 911 781 0
Image cts rejected: 0 859 722 0
Image cts rej (%) : 0.00 94.29 92.45 0.00
filtering data...
Total counts : 0 911 781 0
Total cts rejected: 0 859 722 0
Total cts rej (%) : 0.00 94.29 92.45 0.00
Number of clean counts accepted : 111
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 98
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad85001000s000212h.evt use_events=no
Wrote cleaned events file to ad85001000s000212h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad85001000s000301m.unf because of modeThe sum of the selected column is 3264.8539 The mean of the selected column is 23.658361 The standard deviation of the selected column is 39.154161 The minimum of selected column is 5.8438473 The maximum of selected column is 442.68884 The number of points used in calculation is 138-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3656.6678 The mean of the selected column is 26.691006 The standard deviation of the selected column is 25.064031 The minimum of selected column is 8.8125267 The maximum of selected column is 236.34447 The number of points used in calculation is 137-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<141.1 )&& (S0_PIXL2>0.0 && S0_PIXL2<101.8 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT MEDIUM 15/02/97 03:05:56 0.51E+04 4484 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s000302m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
3822 3375 0 447 0 0
Writing events file
3375 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3822 3375 0 447 0 0
in 4339.70 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 3375
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 1044
Flickering pixels iter, pixels & cnts : 1 1 9
cleaning chip # 2
Hot pixels & counts : 6 852
Flickering pixels iter, pixels & cnts : 1 1 10
cleaning chip # 3
Number of pixels rejected : 13
Number of (internal) image counts : 3375
Number of image cts rejected (N, %) : 1915 56.7407417
By chip : 0 1 2 3
Pixels rejected : 0 6 7 0
Image counts : 0 1594 1781 0
Image cts rejected: 0 1053 862 0
Image cts rej (%) : 0.00 66.06 48.40 0.00
filtering data...
Total counts : 0 1594 1781 0
Total cts rejected: 0 1053 862 0
Total cts rej (%) : 0.00 66.06 48.40 0.00
Number of clean counts accepted : 1460
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 13
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s000302m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad85001000s000302m.evt use_events=no
Wrote cleaned events file to ad85001000s000302m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad85001000s000312m.unf into ad85001000s000312m.evtThe sum of the selected column is 3264.8539 The mean of the selected column is 23.658361 The standard deviation of the selected column is 39.154161 The minimum of selected column is 5.8438473 The maximum of selected column is 442.68884 The number of points used in calculation is 138-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3656.6678 The mean of the selected column is 26.691006 The standard deviation of the selected column is 25.064031 The minimum of selected column is 8.8125267 The maximum of selected column is 236.34447 The number of points used in calculation is 137-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0.0 && S0_PIXL1<141.1 )&& (S0_PIXL2>0.0 && S0_PIXL2<101.8 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT2 MEDIUM 15/02/97 03:05:56 0.51E+04 4597 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s000312m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
3919 3458 0 461 0 0
Writing events file
3458 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3919 3458 0 461 0 0
in 4339.70 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 3458
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 1064
Flickering pixels iter, pixels & cnts : 1 1 9
cleaning chip # 2
Hot pixels & counts : 6 856
Flickering pixels iter, pixels & cnts : 1 1 10
cleaning chip # 3
Number of pixels rejected : 13
Number of (internal) image counts : 3458
Number of image cts rejected (N, %) : 1939 56.0728760
By chip : 0 1 2 3
Pixels rejected : 0 6 7 0
Image counts : 0 1635 1823 0
Image cts rejected: 0 1073 866 0
Image cts rej (%) : 0.00 65.63 47.50 0.00
filtering data...
Total counts : 0 1635 1823 0
Total cts rejected: 0 1073 866 0
Total cts rej (%) : 0.00 65.63 47.50 0.00
Number of clean counts accepted : 1519
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 13
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s000312m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad85001000s000312m.evt use_events=no
Wrote cleaned events file to ad85001000s000312m.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad85001000s000401m.unf because of modeThe sum of the selected column is 271.75086 The mean of the selected column is 22.645905 The standard deviation of the selected column is 6.3799669 The minimum of selected column is 13.468793 The maximum of selected column is 34.718861 The number of points used in calculation is 12-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 660.25209 The mean of the selected column is 55.021007 The standard deviation of the selected column is 61.003707 The minimum of selected column is 17.187553 The maximum of selected column is 236.03200 The number of points used in calculation is 12-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>3.5 && S0_PIXL1<41.7 )&& (S0_PIXL2>0.0 && S0_PIXL2<238 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT MEDIUM 14/02/97 23:51:48 0.18E+04 1903 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s000402m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
1521 450 0 1071 0 0
Writing events file
450 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1521 450 0 1071 0 0
in 438.78 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 450
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 4 123
Flickering pixels iter, pixels & cnts : 1 2 7
cleaning chip # 2
Hot pixels & counts : 9 165
Flickering pixels iter, pixels & cnts : 1 1 4
cleaning chip # 3
Number of pixels rejected : 16
Number of (internal) image counts : 450
Number of image cts rejected (N, %) : 299 66.4444427
By chip : 0 1 2 3
Pixels rejected : 0 6 10 0
Image counts : 0 209 241 0
Image cts rejected: 0 130 169 0
Image cts rej (%) : 0.00 62.20 70.12 0.00
filtering data...
Total counts : 0 209 241 0
Total cts rejected: 0 130 169 0
Total cts rej (%) : 0.00 62.20 70.12 0.00
Number of clean counts accepted : 151
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 16
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s000402m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad85001000s000402m.evt use_events=no
Wrote cleaned events file to ad85001000s000402m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad85001000s000412m.unf into ad85001000s000412m.evtThe sum of the selected column is 271.75086 The mean of the selected column is 22.645905 The standard deviation of the selected column is 6.3799669 The minimum of selected column is 13.468793 The maximum of selected column is 34.718861 The number of points used in calculation is 12-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 660.25209 The mean of the selected column is 55.021007 The standard deviation of the selected column is 61.003707 The minimum of selected column is 17.187553 The maximum of selected column is 236.03200 The number of points used in calculation is 12-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>3.5 && S0_PIXL1<41.7 )&& (S0_PIXL2>0.0 && S0_PIXL2<238 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT2 MEDIUM 14/02/97 23:51:48 0.18E+04 1954 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s000412m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
1570 463 0 1107 0 0
Writing events file
463 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1570 463 0 1107 0 0
in 438.78 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 463
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 4 126
Flickering pixels iter, pixels & cnts : 1 2 7
cleaning chip # 2
Hot pixels & counts : 9 170
Flickering pixels iter, pixels & cnts : 1 1 4
cleaning chip # 3
Number of pixels rejected : 16
Number of (internal) image counts : 463
Number of image cts rejected (N, %) : 307 66.3066940
By chip : 0 1 2 3
Pixels rejected : 0 6 10 0
Image counts : 0 215 248 0
Image cts rejected: 0 133 174 0
Image cts rej (%) : 0.00 61.86 70.16 0.00
filtering data...
Total counts : 0 215 248 0
Total cts rejected: 0 133 174 0
Total cts rej (%) : 0.00 61.86 70.16 0.00
Number of clean counts accepted : 156
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 16
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s000412m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad85001000s000412m.evt use_events=no
Wrote cleaned events file to ad85001000s000412m.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad85001000s000501l.unf because of modeThe sum of the selected column is 14540.364 The mean of the selected column is 35.551012 The standard deviation of the selected column is 20.695425 The minimum of selected column is 5.6428847 The maximum of selected column is 320.81348 The number of points used in calculation is 409-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 13869.417 The mean of the selected column is 33.910555 The standard deviation of the selected column is 23.487032 The minimum of selected column is 6.8611321 The maximum of selected column is 378.65741 The number of points used in calculation is 409-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0.0 && S1_PIXL1<97.6 )&& (S1_PIXL2>0.0 && S1_PIXL2<104.3 ) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:54:28 0.18E+05 275837 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
254279 205554 0 48725 0 0
Writing events file
205554 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
254279 205554 0 48725 0 0
in 13899.91 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 205554
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 83 104148
Flickering pixels iter, pixels & cnts : 1 54 2137
cleaning chip # 2
Hot pixels & counts : 71 89014
Flickering pixels iter, pixels & cnts : 1 61 3184
Flickering pixels iter, pixels & cnts : 2 1 3
cleaning chip # 3
Number of pixels rejected : 270
Number of (internal) image counts : 205554
Number of image cts rejected (N, %) : 198486 96.5614853
By chip : 0 1 2 3
Pixels rejected : 0 137 133 0
Image counts : 0 111210 94344 0
Image cts rejected: 0 106285 92201 0
Image cts rej (%) : 0.00 95.57 97.73 0.00
filtering data...
Total counts : 0 111210 94344 0
Total cts rejected: 0 106285 92201 0
Total cts rej (%) : 0.00 95.57 97.73 0.00
Number of clean counts accepted : 7068
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 270
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad85001000s100102h.evt use_events=no
Wrote cleaned events file to ad85001000s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad85001000s100112h.unf into ad85001000s100112h.evtThe sum of the selected column is 14540.364 The mean of the selected column is 35.551012 The standard deviation of the selected column is 20.695425 The minimum of selected column is 5.6428847 The maximum of selected column is 320.81348 The number of points used in calculation is 409-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 13869.417 The mean of the selected column is 33.910555 The standard deviation of the selected column is 23.487032 The minimum of selected column is 6.8611321 The maximum of selected column is 378.65741 The number of points used in calculation is 409-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0.0 && S1_PIXL1<97.6 )&& (S1_PIXL2>0.0 && S1_PIXL2<104.3 ) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 HIGH 14/02/97 23:54:28 0.18E+05 276718 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
257658 208093 0 49565 0 0
Writing events file
208093 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
257658 208093 0 49565 0 0
in 13899.91 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 208093
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 82 105245
Flickering pixels iter, pixels & cnts : 1 55 2589
cleaning chip # 2
Hot pixels & counts : 72 89970
Flickering pixels iter, pixels & cnts : 1 60 2978
Flickering pixels iter, pixels & cnts : 2 1 3
cleaning chip # 3
Number of pixels rejected : 270
Number of (internal) image counts : 208093
Number of image cts rejected (N, %) : 200785 96.4881058
By chip : 0 1 2 3
Pixels rejected : 0 137 133 0
Image counts : 0 112917 95176 0
Image cts rejected: 0 107834 92951 0
Image cts rej (%) : 0.00 95.50 97.66 0.00
filtering data...
Total counts : 0 112917 95176 0
Total cts rejected: 0 107834 92951 0
Total cts rej (%) : 0.00 95.50 97.66 0.00
Number of clean counts accepted : 7308
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 270
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad85001000s100112h.evt use_events=no
Wrote cleaned events file to ad85001000s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad85001000s100201m.unf because of modeThe sum of the selected column is 4904.5258 The mean of the selected column is 32.916281 The standard deviation of the selected column is 25.553679 The minimum of selected column is 13.656475 The maximum of selected column is 300.34467 The number of points used in calculation is 149-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 4791.4727 The mean of the selected column is 32.157535 The standard deviation of the selected column is 25.716441 The minimum of selected column is 12.437538 The maximum of selected column is 303.96967 The number of points used in calculation is 149-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0.0 && S1_PIXL1<109.5 )&& (S1_PIXL2>0.0 && S1_PIXL2<109.3 ) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT MEDIUM 14/02/97 23:51:48 0.69E+04 18462 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s100202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
17081 12674 0 4407 0 0
Writing events file
12674 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
17081 12674 0 4407 0 0
in 4825.27 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 12674
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 15 6150
Flickering pixels iter, pixels & cnts : 1 9 108
cleaning chip # 2
Hot pixels & counts : 9 4185
Flickering pixels iter, pixels & cnts : 1 2 38
cleaning chip # 3
Number of pixels rejected : 35
Number of (internal) image counts : 12674
Number of image cts rejected (N, %) : 10481 82.6968613
By chip : 0 1 2 3
Pixels rejected : 0 24 11 0
Image counts : 0 7792 4882 0
Image cts rejected: 0 6258 4223 0
Image cts rej (%) : 0.00 80.31 86.50 0.00
filtering data...
Total counts : 0 7792 4882 0
Total cts rejected: 0 6258 4223 0
Total cts rej (%) : 0.00 80.31 86.50 0.00
Number of clean counts accepted : 2193
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 35
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad85001000s100202m.evt use_events=no
Wrote cleaned events file to ad85001000s100202m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad85001000s100212m.unf into ad85001000s100212m.evtThe sum of the selected column is 4904.5258 The mean of the selected column is 32.916281 The standard deviation of the selected column is 25.553679 The minimum of selected column is 13.656475 The maximum of selected column is 300.34467 The number of points used in calculation is 149-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 4791.4727 The mean of the selected column is 32.157535 The standard deviation of the selected column is 25.716441 The minimum of selected column is 12.437538 The maximum of selected column is 303.96967 The number of points used in calculation is 149-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0.0 && S1_PIXL1<109.5 )&& (S1_PIXL2>0.0 && S1_PIXL2<109.3 ) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 MEDIUM 14/02/97 23:51:48 0.69E+04 18552 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s100212m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
17207 12740 0 4467 0 0
Writing events file
12740 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
17207 12740 0 4467 0 0
in 4825.27 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 12740
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 15 6156
Flickering pixels iter, pixels & cnts : 1 9 109
cleaning chip # 2
Hot pixels & counts : 9 4197
Flickering pixels iter, pixels & cnts : 1 2 38
cleaning chip # 3
Number of pixels rejected : 35
Number of (internal) image counts : 12740
Number of image cts rejected (N, %) : 10500 82.4175797
By chip : 0 1 2 3
Pixels rejected : 0 24 11 0
Image counts : 0 7828 4912 0
Image cts rejected: 0 6265 4235 0
Image cts rej (%) : 0.00 80.03 86.22 0.00
filtering data...
Total counts : 0 7828 4912 0
Total cts rejected: 0 6265 4235 0
Total cts rej (%) : 0.00 80.03 86.22 0.00
Number of clean counts accepted : 2240
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 35
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s100212m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad85001000s100212m.evt use_events=no
Wrote cleaned events file to ad85001000s100212m.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad85001000s100301l.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0)&& (S1_PIXL2>0) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT LOW 15/02/97 02:42:28 0.40E+04 3130 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s100302l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad85001000s100302l.evt use_events=no
Wrote cleaned events file to ad85001000s100302l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad85001000s100302l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL1>0)&& (S1_PIXL2>0) ) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 LOW 15/02/97 02:42:28 0.40E+04 3145 0110
Processing file: /data/data24/seq_proc/85001000.005/ad85001000s100312l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data24/seq_proc/85001000.005/screen_in_event.xsl
reading data file: /data/data24/seq_proc/85001000.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000s100312l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad85001000s100312l.evt use_events=no
Wrote cleaned events file to ad85001000s100312l.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad85001000s100312l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 37626 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200170h.unf
Total Good Bad: Region Time Phase Cut
37626 22777 14172 677 0 0
Writing events file
22777 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
37626 22777 14172 677 0 0
in 14629.98 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
22777 21951 826
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad85001000g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 21951 in ad85001000g200170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.57E+04 13711 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200270m.unf
Total Good Bad: Region Time Phase Cut
13711 8440 5065 206 0 0
Writing events file
8440 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13711 8440 5065 206 0 0
in 5424.20 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
8440 8162 278
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad85001000g200270m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 8162 in ad85001000g200270m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH LOW 15/02/97 02:46:52 0.31E+04 2258 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/ad85001000g200370l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad85001000g200370l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad85001000g200370l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 1255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200470h.unf
Total Good Bad: Region Time Phase Cut
1255 813 442 0 0 0
Writing events file
813 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1255 813 442 0 0 0
in 502.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
813 789 24
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000g200470h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad85001000g200470h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 789 in ad85001000g200470h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 34721 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300170h.unf
Total Good Bad: Region Time Phase Cut
34721 22770 11287 664 0 0
Writing events file
22770 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
34721 22770 11287 664 0 0
in 14623.98 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
22770 21923 847
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad85001000g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 21923 in ad85001000g300170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.57E+04 12681 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300270m.unf
Total Good Bad: Region Time Phase Cut
12681 8456 4046 179 0 0
Writing events file
8456 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12681 8456 4046 179 0 0
in 5424.20 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
8456 8174 282
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad85001000g300270m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 8174 in ad85001000g300270m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH LOW 15/02/97 02:46:52 0.31E+04 1995 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/ad85001000g300370l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad85001000g300370l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad85001000g300370l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 1165 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300470h.unf
Total Good Bad: Region Time Phase Cut
1165 794 371 0 0 0
Writing events file
794 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1165 794 371 0 0 0
in 502.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
794 760 34
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!screen:ASCA > read events ad85001000g300470h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad85001000g300470h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 760 in ad85001000g300470h.unf-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad85001000g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970214_2351.1240
making an exposure map...
Aspect RA/DEC/ROLL : 49.8927 42.1259 112.1993
Mean RA/DEC/ROLL : 49.8906 42.1511 112.1993
Pnt RA/DEC/ROLL : 49.8964 42.1030 112.1993
Image rebin factor : 1
Attitude Records : 41430
GTI intervals : 22
Total GTI (secs) : 14629.978
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3245.4931641 3245.4931641
20 Percent Complete: Total/live time: 3245.4931641 3245.4931641
30 Percent Complete: Total/live time: 5721.4853516 5721.4853516
40 Percent Complete: Total/live time: 6113.4838867 6113.4838867
50 Percent Complete: Total/live time: 8245.4062500 8245.4062500
60 Percent Complete: Total/live time: 9018.4042969 9018.4042969
70 Percent Complete: Total/live time: 11913.8886719 11913.8886719
80 Percent Complete: Total/live time: 11913.8886719 11913.8886719
90 Percent Complete: Total/live time: 14629.9794922 14629.9794922
100 Percent Complete: Total/live time: 14629.9794922 14629.9794922
Number of attitude steps used: 26
Number of attitude steps avail: 35800
Mean RA/DEC pixel offset: -11.0072 -4.0209
writing expo file: ad85001000g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad85001000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad85001000g200170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21951 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200170h.evt
Total Good Bad: Region Time Phase Cut
21951 21788 163 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21951 21788 163 0 0 0
in 14629.98 seconds
Image has 21788 counts for 1.489 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200170h.evt
Total Good Bad: Region Time Phase Cut
21951 10913 163 0 0 10875
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21951 10913 163 0 0 10875
in 14629.98 seconds
Image has 10913 counts for 0.7459 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200170h.evt
Total Good Bad: Region Time Phase Cut
21951 10958 163 0 0 10830
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21951 10958 163 0 0 10830
in 14629.98 seconds
Image has 10958 counts for 0.7490 counts/sec
Command not found; type ? for a command listing
!ad85001000g200170h:ASCA >
!ad85001000g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad85001000g200170h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!ad85001000g200170h:ASCA > read events ad85001000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!ad85001000g200170h:ASCA-GIS2-PH > set image sky
!ad85001000g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad85001000g200170h:ASCA-GIS2-PH > extract image
!ad85001000g200170h:ASCA-GIS2-PH > save image outfile=ad85001000g200170h.img
Wrote image to file ad85001000g200170h.img
!ad85001000g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad85001000g200170h:ASCA-GIS2-PH > extract image
!ad85001000g200170h:ASCA-GIS2-PH > save image outfile=ad85001000g200170h_lo.img
Wrote image to file ad85001000g200170h_lo.img
!ad85001000g200170h:ASCA-GIS2-PH > clear pha_cut
!ad85001000g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad85001000g200170h:ASCA-GIS2-PH > extract image
!ad85001000g200170h:ASCA-GIS2-PH > save image outfile=ad85001000g200170h_hi.img
Wrote image to file ad85001000g200170h_hi.img
!ad85001000g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad85001000g200270m.expo
ASCAEXPO_V0.9b
reading data file: ad85001000g200270m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970214_2351.1240
making an exposure map...
Aspect RA/DEC/ROLL : 49.8927 42.1259 112.1992
Mean RA/DEC/ROLL : 49.8882 42.1511 112.1992
Pnt RA/DEC/ROLL : 49.9133 42.0994 112.1992
Image rebin factor : 1
Attitude Records : 41430
GTI intervals : 5
Total GTI (secs) : 5424.201
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 799.9622192 799.9622192
20 Percent Complete: Total/live time: 1359.9604492 1359.9604492
30 Percent Complete: Total/live time: 2621.0742188 2621.0742188
40 Percent Complete: Total/live time: 2621.0742188 2621.0742188
50 Percent Complete: Total/live time: 3089.0727539 3089.0727539
60 Percent Complete: Total/live time: 4637.0678711 4637.0678711
70 Percent Complete: Total/live time: 4637.0678711 4637.0678711
80 Percent Complete: Total/live time: 5424.2011719 5424.2011719
100 Percent Complete: Total/live time: 5424.2011719 5424.2011719
Number of attitude steps used: 17
Number of attitude steps avail: 7798
Mean RA/DEC pixel offset: -11.6280 -2.6958
writing expo file: ad85001000g200270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad85001000g200270m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad85001000g200270m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.54E+04 8162 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200270m.evt
Total Good Bad: Region Time Phase Cut
8162 8088 74 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8162 8088 74 0 0 0
in 5424.20 seconds
Image has 8088 counts for 1.491 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200270m.evt
Total Good Bad: Region Time Phase Cut
8162 3975 74 0 0 4113
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8162 3975 74 0 0 4113
in 5424.20 seconds
Image has 3975 counts for 0.7328 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200270m.evt
Total Good Bad: Region Time Phase Cut
8162 4154 74 0 0 3934
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8162 4154 74 0 0 3934
in 5424.20 seconds
Image has 4154 counts for 0.7658 counts/sec
Command not found; type ? for a command listing
!ad85001000g200270m:ASCA >
!ad85001000g200270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad85001000g200270m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!ad85001000g200270m:ASCA > read events ad85001000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!ad85001000g200270m:ASCA-GIS2-PH > set image sky
!ad85001000g200270m:ASCA-GIS2-PH > filter region corner_point.reg
!ad85001000g200270m:ASCA-GIS2-PH > extract image
!ad85001000g200270m:ASCA-GIS2-PH > save image outfile=ad85001000g200270m.img
Wrote image to file ad85001000g200270m.img
!ad85001000g200270m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad85001000g200270m:ASCA-GIS2-PH > extract image
!ad85001000g200270m:ASCA-GIS2-PH > save image outfile=ad85001000g200270m_lo.img
Wrote image to file ad85001000g200270m_lo.img
!ad85001000g200270m:ASCA-GIS2-PH > clear pha_cut
!ad85001000g200270m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad85001000g200270m:ASCA-GIS2-PH > extract image
!ad85001000g200270m:ASCA-GIS2-PH > save image outfile=ad85001000g200270m_hi.img
Wrote image to file ad85001000g200270m_hi.img
!ad85001000g200270m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad85001000g200470h.expo
ASCAEXPO_V0.9b
reading data file: ad85001000g200470h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970214_2351.1240
making an exposure map...
Aspect RA/DEC/ROLL : 49.8927 42.1259 112.1978
Mean RA/DEC/ROLL : 49.8872 42.1514 112.1978
Pnt RA/DEC/ROLL : 49.8976 42.1026 112.1978
Image rebin factor : 1
Attitude Records : 41430
GTI intervals : 1
Total GTI (secs) : 501.998
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 501.9984741 501.9984741
100 Percent Complete: Total/live time: 501.9984741 501.9984741
Number of attitude steps used: 2
Number of attitude steps avail: 998
Mean RA/DEC pixel offset: -6.1197 -1.4146
writing expo file: ad85001000g200470h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad85001000g200470h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad85001000g200470h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 789 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200470h.evt
Total Good Bad: Region Time Phase Cut
789 783 6 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
789 783 6 0 0 0
in 502.00 seconds
Image has 783 counts for 1.560 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200470h.evt
Total Good Bad: Region Time Phase Cut
789 388 6 0 0 395
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
789 388 6 0 0 395
in 502.00 seconds
Image has 388 counts for 0.7729 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200470h.evt
Total Good Bad: Region Time Phase Cut
789 398 6 0 0 385
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
789 398 6 0 0 385
in 502.00 seconds
Image has 398 counts for 0.7928 counts/sec
Command not found; type ? for a command listing
!ad85001000g200470h:ASCA >
!ad85001000g200470h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad85001000g200470h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!ad85001000g200470h:ASCA > read events ad85001000g200470h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!ad85001000g200470h:ASCA-GIS2-PH > set image sky
!ad85001000g200470h:ASCA-GIS2-PH > filter region corner_point.reg
!ad85001000g200470h:ASCA-GIS2-PH > extract image
!ad85001000g200470h:ASCA-GIS2-PH > save image outfile=ad85001000g200470h.img
Wrote image to file ad85001000g200470h.img
!ad85001000g200470h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad85001000g200470h:ASCA-GIS2-PH > extract image
!ad85001000g200470h:ASCA-GIS2-PH > save image outfile=ad85001000g200470h_lo.img
Wrote image to file ad85001000g200470h_lo.img
!ad85001000g200470h:ASCA-GIS2-PH > clear pha_cut
!ad85001000g200470h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad85001000g200470h:ASCA-GIS2-PH > extract image
!ad85001000g200470h:ASCA-GIS2-PH > save image outfile=ad85001000g200470h_hi.img
Wrote image to file ad85001000g200470h_hi.img
!ad85001000g200470h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad85001000g300170h.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad85001000g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970214_2351.1240
making an exposure map...
Aspect RA/DEC/ROLL : 49.8927 42.1259 112.2058
Mean RA/DEC/ROLL : 49.9002 42.1273 112.2058
Pnt RA/DEC/ROLL : 49.8869 42.1268 112.2058
Image rebin factor : 1
Attitude Records : 41430
GTI intervals : 22
Total GTI (secs) : 14623.978
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3243.4931641 3243.4931641
20 Percent Complete: Total/live time: 3243.4931641 3243.4931641
30 Percent Complete: Total/live time: 5719.4853516 5719.4853516
40 Percent Complete: Total/live time: 6111.4838867 6111.4838867
50 Percent Complete: Total/live time: 8243.4062500 8243.4062500
60 Percent Complete: Total/live time: 9016.4042969 9016.4042969
70 Percent Complete: Total/live time: 11911.8886719 11911.8886719
80 Percent Complete: Total/live time: 11911.8886719 11911.8886719
90 Percent Complete: Total/live time: 14623.9794922 14623.9794922
100 Percent Complete: Total/live time: 14623.9794922 14623.9794922
Number of attitude steps used: 26
Number of attitude steps avail: 35796
Mean RA/DEC pixel offset: 0.6069 -2.8671
writing expo file: ad85001000g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad85001000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad85001000g300170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21923 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300170h.evt
Total Good Bad: Region Time Phase Cut
21923 21756 167 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21923 21756 167 0 0 0
in 14623.98 seconds
Image has 21756 counts for 1.488 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300170h.evt
Total Good Bad: Region Time Phase Cut
21923 11029 167 0 0 10727
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21923 11029 167 0 0 10727
in 14623.98 seconds
Image has 11029 counts for 0.7542 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300170h.evt
Total Good Bad: Region Time Phase Cut
21923 10803 167 0 0 10953
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21923 10803 167 0 0 10953
in 14623.98 seconds
Image has 10803 counts for 0.7387 counts/sec
Command not found; type ? for a command listing
!ad85001000g300170h:ASCA >
!ad85001000g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad85001000g300170h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!ad85001000g300170h:ASCA > read events ad85001000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!ad85001000g300170h:ASCA-GIS3-PH > set image sky
!ad85001000g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad85001000g300170h:ASCA-GIS3-PH > extract image
!ad85001000g300170h:ASCA-GIS3-PH > save image outfile=ad85001000g300170h.img
Wrote image to file ad85001000g300170h.img
!ad85001000g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad85001000g300170h:ASCA-GIS3-PH > extract image
!ad85001000g300170h:ASCA-GIS3-PH > save image outfile=ad85001000g300170h_lo.img
Wrote image to file ad85001000g300170h_lo.img
!ad85001000g300170h:ASCA-GIS3-PH > clear pha_cut
!ad85001000g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad85001000g300170h:ASCA-GIS3-PH > extract image
!ad85001000g300170h:ASCA-GIS3-PH > save image outfile=ad85001000g300170h_hi.img
Wrote image to file ad85001000g300170h_hi.img
!ad85001000g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad85001000g300270m.expo
ASCAEXPO_V0.9b
reading data file: ad85001000g300270m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970214_2351.1240
making an exposure map...
Aspect RA/DEC/ROLL : 49.8927 42.1259 112.2057
Mean RA/DEC/ROLL : 49.8978 42.1273 112.2057
Pnt RA/DEC/ROLL : 49.9038 42.1232 112.2057
Image rebin factor : 1
Attitude Records : 41430
GTI intervals : 5
Total GTI (secs) : 5424.201
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 799.9622192 799.9622192
20 Percent Complete: Total/live time: 1359.9604492 1359.9604492
30 Percent Complete: Total/live time: 2621.0742188 2621.0742188
40 Percent Complete: Total/live time: 2621.0742188 2621.0742188
50 Percent Complete: Total/live time: 3089.0727539 3089.0727539
60 Percent Complete: Total/live time: 4637.0678711 4637.0678711
70 Percent Complete: Total/live time: 4637.0678711 4637.0678711
80 Percent Complete: Total/live time: 5424.2011719 5424.2011719
100 Percent Complete: Total/live time: 5424.2011719 5424.2011719
Number of attitude steps used: 17
Number of attitude steps avail: 7798
Mean RA/DEC pixel offset: -0.2598 -1.5665
writing expo file: ad85001000g300270m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad85001000g300270m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad85001000g300270m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.54E+04 8174 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300270m.evt
Total Good Bad: Region Time Phase Cut
8174 8129 45 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8174 8129 45 0 0 0
in 5424.20 seconds
Image has 8129 counts for 1.499 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300270m.evt
Total Good Bad: Region Time Phase Cut
8174 4040 45 0 0 4089
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8174 4040 45 0 0 4089
in 5424.20 seconds
Image has 4040 counts for 0.7448 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300270m.evt
Total Good Bad: Region Time Phase Cut
8174 4125 45 0 0 4004
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8174 4125 45 0 0 4004
in 5424.20 seconds
Image has 4125 counts for 0.7605 counts/sec
Command not found; type ? for a command listing
!ad85001000g300270m:ASCA >
!ad85001000g300270m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad85001000g300270m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!ad85001000g300270m:ASCA > read events ad85001000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!ad85001000g300270m:ASCA-GIS3-PH > set image sky
!ad85001000g300270m:ASCA-GIS3-PH > filter region corner_point.reg
!ad85001000g300270m:ASCA-GIS3-PH > extract image
!ad85001000g300270m:ASCA-GIS3-PH > save image outfile=ad85001000g300270m.img
Wrote image to file ad85001000g300270m.img
!ad85001000g300270m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad85001000g300270m:ASCA-GIS3-PH > extract image
!ad85001000g300270m:ASCA-GIS3-PH > save image outfile=ad85001000g300270m_lo.img
Wrote image to file ad85001000g300270m_lo.img
!ad85001000g300270m:ASCA-GIS3-PH > clear pha_cut
!ad85001000g300270m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad85001000g300270m:ASCA-GIS3-PH > extract image
!ad85001000g300270m:ASCA-GIS3-PH > save image outfile=ad85001000g300270m_hi.img
Wrote image to file ad85001000g300270m_hi.img
!ad85001000g300270m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad85001000g300470h.expo
ASCAEXPO_V0.9b
reading data file: ad85001000g300470h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970214_2351.1240
making an exposure map...
Aspect RA/DEC/ROLL : 49.8927 42.1259 112.2043
Mean RA/DEC/ROLL : 49.8967 42.1276 112.2043
Pnt RA/DEC/ROLL : 49.8880 42.1265 112.2043
Image rebin factor : 1
Attitude Records : 41430
GTI intervals : 1
Total GTI (secs) : 501.998
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 501.9984741 501.9984741
100 Percent Complete: Total/live time: 501.9984741 501.9984741
Number of attitude steps used: 2
Number of attitude steps avail: 998
Mean RA/DEC pixel offset: -0.0803 -0.8147
writing expo file: ad85001000g300470h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad85001000g300470h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad85001000g300470h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 760 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300470h.evt
Total Good Bad: Region Time Phase Cut
760 756 4 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
760 756 4 0 0 0
in 502.00 seconds
Image has 756 counts for 1.506 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300470h.evt
Total Good Bad: Region Time Phase Cut
760 404 4 0 0 352
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
760 404 4 0 0 352
in 502.00 seconds
Image has 404 counts for 0.8048 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300470h.evt
Total Good Bad: Region Time Phase Cut
760 353 4 0 0 403
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
760 353 4 0 0 403
in 502.00 seconds
Image has 353 counts for 0.7032 counts/sec
Command not found; type ? for a command listing
!ad85001000g300470h:ASCA >
!ad85001000g300470h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad85001000g300470h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!ad85001000g300470h:ASCA > read events ad85001000g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!ad85001000g300470h:ASCA-GIS3-PH > set image sky
!ad85001000g300470h:ASCA-GIS3-PH > filter region corner_point.reg
!ad85001000g300470h:ASCA-GIS3-PH > extract image
!ad85001000g300470h:ASCA-GIS3-PH > save image outfile=ad85001000g300470h.img
Wrote image to file ad85001000g300470h.img
!ad85001000g300470h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad85001000g300470h:ASCA-GIS3-PH > extract image
!ad85001000g300470h:ASCA-GIS3-PH > save image outfile=ad85001000g300470h_lo.img
Wrote image to file ad85001000g300470h_lo.img
!ad85001000g300470h:ASCA-GIS3-PH > clear pha_cut
!ad85001000g300470h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad85001000g300470h:ASCA-GIS3-PH > extract image
!ad85001000g300470h:ASCA-GIS3-PH > save image outfile=ad85001000g300470h_hi.img
Wrote image to file ad85001000g300470h_hi.img
!ad85001000g300470h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad85001000s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad85001000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970214_2351.1240
making an exposure map...
Aspect RA/DEC/ROLL : 49.8927 42.1259 112.2154
Mean RA/DEC/ROLL : 49.9143 42.1449 112.2154
Pnt RA/DEC/ROLL : 49.8732 42.1091 112.2154
Image rebin factor : 4
Attitude Records : 41430
Hot Pixels : 151
GTI intervals : 27
Total GTI (secs) : 13761.954
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1547.9345703 1547.9345703
20 Percent Complete: Total/live time: 3166.9294434 3166.9294434
30 Percent Complete: Total/live time: 5563.4042969 5563.4042969
40 Percent Complete: Total/live time: 5955.4028320 5955.4028320
50 Percent Complete: Total/live time: 8509.3642578 8509.3642578
60 Percent Complete: Total/live time: 8509.3642578 8509.3642578
70 Percent Complete: Total/live time: 10944.3125000 10944.3125000
80 Percent Complete: Total/live time: 11710.3095703 11710.3095703
90 Percent Complete: Total/live time: 13761.9541016 13761.9541016
100 Percent Complete: Total/live time: 13761.9541016 13761.9541016
Number of attitude steps used: 22
Number of attitude steps avail: 34955
Mean RA/DEC pixel offset: -48.3373 -96.3584
writing expo file: ad85001000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad85001000s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad85001000s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:54:28 0.14E+05 5029 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000102h.evt
Total Good Bad: Region Time Phase Cut
5029 5029 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5029 5029 0 0 0 0
in 13761.95 seconds
Image has 5029 counts for 0.3654 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000102h.evt
Total Good Bad: Region Time Phase Cut
5029 2920 0 0 0 2109
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5029 2920 0 0 0 2109
in 13761.95 seconds
Image has 2920 counts for 0.2122 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000102h.evt
Total Good Bad: Region Time Phase Cut
5029 2115 0 0 0 2914
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5029 2115 0 0 0 2914
in 13761.95 seconds
Image has 2115 counts for 0.1537 counts/sec
Command not found; type ? for a command listing
!ad85001000s000102h:ASCA >
!ad85001000s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad85001000s000102h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!ad85001000s000102h:ASCA > read events ad85001000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!ad85001000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad85001000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad85001000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad85001000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad85001000s000102h.img
Wrote image to file ad85001000s000102h.img
!ad85001000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad85001000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad85001000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad85001000s000102h_lo.img
Wrote image to file ad85001000s000102h_lo.img
!ad85001000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad85001000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad85001000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad85001000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad85001000s000102h_hi.img
Wrote image to file ad85001000s000102h_hi.img
!ad85001000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad85001000s000202h.expo
ASCAEXPO_V0.9b
reading data file: ad85001000s000202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970214_2351.1240
making an exposure map...
Aspect RA/DEC/ROLL : 49.8927 42.1259 112.2153
Mean RA/DEC/ROLL : 49.9142 42.1450 112.2153
Pnt RA/DEC/ROLL : 49.8696 42.1091 112.2153
Image rebin factor : 4
Attitude Records : 41430
Hot Pixels : 98
GTI intervals : 3
Total GTI (secs) : 225.636
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 69.8967743 69.8967743
20 Percent Complete: Total/live time: 69.8967743 69.8967743
30 Percent Complete: Total/live time: 139.7755737 139.7755737
40 Percent Complete: Total/live time: 139.7755737 139.7755737
50 Percent Complete: Total/live time: 225.6364441 225.6364441
100 Percent Complete: Total/live time: 225.6364441 225.6364441
Number of attitude steps used: 4
Number of attitude steps avail: 8108
Mean RA/DEC pixel offset: -40.3551 -73.4720
writing expo file: ad85001000s000202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad85001000s000202h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad85001000s000202h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT HIGH 15/02/97 06:02:48 0.23E+03 106 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000202h.evt
Total Good Bad: Region Time Phase Cut
106 106 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
106 106 0 0 0 0
in 225.64 seconds
Image has 106 counts for 0.4698 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000202h.evt
Total Good Bad: Region Time Phase Cut
106 73 0 0 0 33
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
106 73 0 0 0 33
in 225.64 seconds
Image has 73 counts for 0.3235 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000202h.evt
Total Good Bad: Region Time Phase Cut
106 33 0 0 0 73
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
106 33 0 0 0 73
in 225.64 seconds
Image has 33 counts for 0.1463 counts/sec
Command not found; type ? for a command listing
!ad85001000s000202h:ASCA >
!ad85001000s000202h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad85001000s000202h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!ad85001000s000202h:ASCA > read events ad85001000s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!ad85001000s000202h:ASCA-SIS0-BRIGHT > set image sky
!ad85001000s000202h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad85001000s000202h:ASCA-SIS0-BRIGHT > extract image
!ad85001000s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad85001000s000202h.img
Wrote image to file ad85001000s000202h.img
!ad85001000s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad85001000s000202h:ASCA-SIS0-BRIGHT > extract image
!ad85001000s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad85001000s000202h_lo.img
Wrote image to file ad85001000s000202h_lo.img
!ad85001000s000202h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad85001000s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad85001000s000202h:ASCA-SIS0-BRIGHT > extract image
!ad85001000s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad85001000s000202h_hi.img
Wrote image to file ad85001000s000202h_hi.img
!ad85001000s000202h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad85001000s000302m.expo
ASCAEXPO_V0.9b
reading data file: ad85001000s000302m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970214_2351.1240
making an exposure map...
Aspect RA/DEC/ROLL : 49.8927 42.1259 112.2154
Mean RA/DEC/ROLL : 49.9118 42.1449 112.2154
Pnt RA/DEC/ROLL : 49.8665 42.1095 112.2154
Image rebin factor : 4
Attitude Records : 41430
Hot Pixels : 13
GTI intervals : 6
Total GTI (secs) : 4339.703
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 595.4619751 595.4619751
20 Percent Complete: Total/live time: 1696.5759277 1696.5759277
30 Percent Complete: Total/live time: 1696.5759277 1696.5759277
40 Percent Complete: Total/live time: 2164.5744629 2164.5744629
50 Percent Complete: Total/live time: 2240.5742188 2240.5742188
60 Percent Complete: Total/live time: 3648.5698242 3648.5698242
70 Percent Complete: Total/live time: 3648.5698242 3648.5698242
80 Percent Complete: Total/live time: 4339.7031250 4339.7031250
100 Percent Complete: Total/live time: 4339.7031250 4339.7031250
Number of attitude steps used: 12
Number of attitude steps avail: 8066
Mean RA/DEC pixel offset: -49.7649 -87.8652
writing expo file: ad85001000s000302m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad85001000s000302m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad85001000s000302m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT MEDIUM 15/02/97 03:05:56 0.43E+04 1460 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000302m.evt
Total Good Bad: Region Time Phase Cut
1460 1460 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1460 1460 0 0 0 0
in 4339.70 seconds
Image has 1460 counts for 0.3364 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000302m.evt
Total Good Bad: Region Time Phase Cut
1460 866 0 0 0 594
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1460 866 0 0 0 594
in 4339.70 seconds
Image has 866 counts for 0.1996 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000302m.evt
Total Good Bad: Region Time Phase Cut
1460 595 0 0 0 865
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1460 595 0 0 0 865
in 4339.70 seconds
Image has 595 counts for 0.1371 counts/sec
Command not found; type ? for a command listing
!ad85001000s000302m:ASCA >
!ad85001000s000302m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad85001000s000302m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!ad85001000s000302m:ASCA > read events ad85001000s000302m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!ad85001000s000302m:ASCA-SIS0-BRIGHT > set image sky
!ad85001000s000302m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad85001000s000302m:ASCA-SIS0-BRIGHT > extract image
!ad85001000s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad85001000s000302m.img
Wrote image to file ad85001000s000302m.img
!ad85001000s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad85001000s000302m:ASCA-SIS0-BRIGHT > extract image
!ad85001000s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad85001000s000302m_lo.img
Wrote image to file ad85001000s000302m_lo.img
!ad85001000s000302m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad85001000s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad85001000s000302m:ASCA-SIS0-BRIGHT > extract image
!ad85001000s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad85001000s000302m_hi.img
Wrote image to file ad85001000s000302m_hi.img
!ad85001000s000302m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad85001000s000402m.expo
ASCAEXPO_V0.9b
reading data file: ad85001000s000402m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970214_2351.1240
making an exposure map...
Aspect RA/DEC/ROLL : 49.8927 42.1259 112.2103
Mean RA/DEC/ROLL : 49.9139 42.1450 112.2103
Pnt RA/DEC/ROLL : 49.8886 42.1057 112.2103
Image rebin factor : 4
Attitude Records : 41430
Hot Pixels : 16
GTI intervals : 5
Total GTI (secs) : 438.783
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 72.9994812 72.9994812
20 Percent Complete: Total/live time: 171.4633026 171.4633026
30 Percent Complete: Total/live time: 171.4633026 171.4633026
40 Percent Complete: Total/live time: 257.1591492 257.1591492
50 Percent Complete: Total/live time: 257.1591492 257.1591492
60 Percent Complete: Total/live time: 342.7834778 342.7834778
70 Percent Complete: Total/live time: 342.7834778 342.7834778
80 Percent Complete: Total/live time: 432.0159302 432.0159302
90 Percent Complete: Total/live time: 432.0159302 432.0159302
100 Percent Complete: Total/live time: 438.7835388 438.7835388
Number of attitude steps used: 30
Number of attitude steps avail: 6643
Mean RA/DEC pixel offset: -74.0071 -143.9581
writing expo file: ad85001000s000402m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad85001000s000402m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad85001000s000402m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT MEDIUM 14/02/97 23:51:48 0.44E+03 151 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000402m.evt
Total Good Bad: Region Time Phase Cut
151 151 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
151 151 0 0 0 0
in 438.78 seconds
Image has 151 counts for 0.3441 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000402m.evt
Total Good Bad: Region Time Phase Cut
151 86 0 0 0 65
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
151 86 0 0 0 65
in 438.78 seconds
Image has 86 counts for 0.1960 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000402m.evt
Total Good Bad: Region Time Phase Cut
151 65 0 0 0 86
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
151 65 0 0 0 86
in 438.78 seconds
Image has 65 counts for 0.1481 counts/sec
Command not found; type ? for a command listing
!ad85001000s000402m:ASCA >
!ad85001000s000402m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad85001000s000402m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!ad85001000s000402m:ASCA > read events ad85001000s000402m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!ad85001000s000402m:ASCA-SIS0-BRIGHT > set image sky
!ad85001000s000402m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad85001000s000402m:ASCA-SIS0-BRIGHT > extract image
!ad85001000s000402m:ASCA-SIS0-BRIGHT > save image outfile=ad85001000s000402m.img
Wrote image to file ad85001000s000402m.img
!ad85001000s000402m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad85001000s000402m:ASCA-SIS0-BRIGHT > extract image
!ad85001000s000402m:ASCA-SIS0-BRIGHT > save image outfile=ad85001000s000402m_lo.img
Wrote image to file ad85001000s000402m_lo.img
!ad85001000s000402m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad85001000s000402m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad85001000s000402m:ASCA-SIS0-BRIGHT > extract image
!ad85001000s000402m:ASCA-SIS0-BRIGHT > save image outfile=ad85001000s000402m_hi.img
Wrote image to file ad85001000s000402m_hi.img
!ad85001000s000402m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad85001000s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad85001000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa970214_2351.1240
making an exposure map...
Aspect RA/DEC/ROLL : 49.8927 42.1259 112.2017
Mean RA/DEC/ROLL : 49.8940 42.1398 112.2017
Pnt RA/DEC/ROLL : 49.8935 42.1142 112.2017
Image rebin factor : 4
Attitude Records : 41430
Hot Pixels : 270
GTI intervals : 27
Total GTI (secs) : 13899.907
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1541.9658203 1541.9658203
20 Percent Complete: Total/live time: 3160.9606934 3160.9606934
30 Percent Complete: Total/live time: 5565.4355469 5565.4355469
40 Percent Complete: Total/live time: 5957.4340820 5957.4340820
50 Percent Complete: Total/live time: 8531.5351562 8531.5351562
60 Percent Complete: Total/live time: 8531.5351562 8531.5351562
70 Percent Complete: Total/live time: 11024.5175781 11024.5175781
80 Percent Complete: Total/live time: 11790.5146484 11790.5146484
90 Percent Complete: Total/live time: 13899.9062500 13899.9062500
100 Percent Complete: Total/live time: 13899.9062500 13899.9062500
Number of attitude steps used: 22
Number of attitude steps avail: 35418
Mean RA/DEC pixel offset: -52.5796 -27.7732
writing expo file: ad85001000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad85001000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad85001000s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:54:28 0.14E+05 7068 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100102h.evt
Total Good Bad: Region Time Phase Cut
7068 7068 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7068 7068 0 0 0 0
in 13899.91 seconds
Image has 7068 counts for 0.5085 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100102h.evt
Total Good Bad: Region Time Phase Cut
7068 4011 0 0 0 3057
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7068 4011 0 0 0 3057
in 13899.91 seconds
Image has 4011 counts for 0.2886 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100102h.evt
Total Good Bad: Region Time Phase Cut
7068 3061 0 0 0 4007
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7068 3061 0 0 0 4007
in 13899.91 seconds
Image has 3061 counts for 0.2202 counts/sec
Command not found; type ? for a command listing
!ad85001000s100102h:ASCA >
!ad85001000s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad85001000s100102h:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!ad85001000s100102h:ASCA > read events ad85001000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!ad85001000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad85001000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad85001000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad85001000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad85001000s100102h.img
Wrote image to file ad85001000s100102h.img
!ad85001000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad85001000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad85001000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad85001000s100102h_lo.img
Wrote image to file ad85001000s100102h_lo.img
!ad85001000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad85001000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad85001000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad85001000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad85001000s100102h_hi.img
Wrote image to file ad85001000s100102h_hi.img
!ad85001000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad85001000s100202m.expo
ASCAEXPO_V0.9b
reading data file: ad85001000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON ON OFF
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa970214_2351.1240
making an exposure map...
Aspect RA/DEC/ROLL : 49.8927 42.1259 112.1967
Mean RA/DEC/ROLL : 49.8920 42.1399 112.1967
Pnt RA/DEC/ROLL : 49.9089 42.1108 112.1967
Image rebin factor : 4
Attitude Records : 41430
Hot Pixels : 35
GTI intervals : 8
Total GTI (secs) : 4825.272
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 536.4171143 536.4171143
20 Percent Complete: Total/live time: 2086.1455078 2086.1455078
30 Percent Complete: Total/live time: 2086.1455078 2086.1455078
40 Percent Complete: Total/live time: 2554.1440430 2554.1440430
50 Percent Complete: Total/live time: 2554.1440430 2554.1440430
60 Percent Complete: Total/live time: 4038.1391602 4038.1391602
70 Percent Complete: Total/live time: 4038.1391602 4038.1391602
80 Percent Complete: Total/live time: 4729.2724609 4729.2724609
90 Percent Complete: Total/live time: 4729.2724609 4729.2724609
100 Percent Complete: Total/live time: 4825.2705078 4825.2705078
Number of attitude steps used: 37
Number of attitude steps avail: 8488
Mean RA/DEC pixel offset: -75.7015 -64.7929
writing expo file: ad85001000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad85001000s100202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad85001000s100202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT MEDIUM 14/02/97 23:51:48 0.48E+04 2193 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100202m.evt
Total Good Bad: Region Time Phase Cut
2193 2193 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2193 2193 0 0 0 0
in 4825.27 seconds
Image has 2193 counts for 0.4545 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100202m.evt
Total Good Bad: Region Time Phase Cut
2193 1213 0 0 0 980
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2193 1213 0 0 0 980
in 4825.27 seconds
Image has 1213 counts for 0.2514 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100202m.evt
Total Good Bad: Region Time Phase Cut
2193 981 0 0 0 1212
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2193 981 0 0 0 1212
in 4825.27 seconds
Image has 981 counts for 0.2033 counts/sec
Command not found; type ? for a command listing
!ad85001000s100202m:ASCA >
!ad85001000s100202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad85001000s100202m:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!ad85001000s100202m:ASCA > read events ad85001000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!ad85001000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad85001000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad85001000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad85001000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad85001000s100202m.img
Wrote image to file ad85001000s100202m.img
!ad85001000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad85001000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad85001000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad85001000s100202m_lo.img
Wrote image to file ad85001000s100202m_lo.img
!ad85001000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad85001000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad85001000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad85001000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad85001000s100202m_hi.img
Wrote image to file ad85001000s100202m_hi.img
!ad85001000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad85001000s000102h.expo ad85001000s000202h.expo ad85001000s000302m.expo ad85001000s000402m.expo ad85001000s100102h.expo ad85001000s100202m.expo-> Summing the following images to produce ad85001000sis32002_all.totsky
ad85001000s000102h.img ad85001000s000202h.img ad85001000s000302m.img ad85001000s000402m.img ad85001000s100102h.img ad85001000s100202m.img-> Summing the following images to produce ad85001000sis32002_lo.totsky
ad85001000s000102h_lo.img ad85001000s000202h_lo.img ad85001000s000302m_lo.img ad85001000s000402m_lo.img ad85001000s100102h_lo.img ad85001000s100202m_lo.img-> Summing the following images to produce ad85001000sis32002_hi.totsky
ad85001000s000102h_hi.img ad85001000s000202h_hi.img ad85001000s000302m_hi.img ad85001000s000402m_hi.img ad85001000s100102h_hi.img ad85001000s100202m_hi.img-> Running XIMAGE to create ad85001000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad85001000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 6.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 6 min: 0 ![2]XIMAGE> read/exp_map ad85001000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 591.504 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 591 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 16.0000 16 0 ![9]XIMAGE> exit-> Summing gis images
ad85001000g200170h.expo ad85001000g200270m.expo ad85001000g200470h.expo ad85001000g300170h.expo ad85001000g300270m.expo ad85001000g300470h.expo-> Summing the following images to produce ad85001000gis25670_all.totsky
ad85001000g200170h.img ad85001000g200270m.img ad85001000g200470h.img ad85001000g300170h.img ad85001000g300270m.img ad85001000g300470h.img-> Summing the following images to produce ad85001000gis25670_lo.totsky
ad85001000g200170h_lo.img ad85001000g200270m_lo.img ad85001000g200470h_lo.img ad85001000g300170h_lo.img ad85001000g300270m_lo.img ad85001000g300470h_lo.img-> Summing the following images to produce ad85001000gis25670_hi.totsky
ad85001000g200170h_hi.img ad85001000g200270m_hi.img ad85001000g200470h_hi.img ad85001000g300170h_hi.img ad85001000g300270m_hi.img ad85001000g300470h_hi.img-> Running XIMAGE to create ad85001000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad85001000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 18.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 18 min: 0 ![2]XIMAGE> read/exp_map ad85001000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 685.106 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 685 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 17.0000 17 0 ![9]XIMAGE> exit
118 37 0.000344009 179 79 13.5402-> Smoothing ad85001000gis25670_hi.totsky with ad85001000gis25670.totexpo
143 38 0.000152956 177 88 13.2243-> Smoothing ad85001000gis25670_lo.totsky with ad85001000gis25670.totexpo
118 37 0.00022032 179 70 16.3697-> Determining extraction radii
118 37 79 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad85001000gis25670.src
190 55 6.8685e-05 247 135 9.13751-> Smoothing ad85001000sis32002_hi.totsky with ad85001000sis32002.totexpo
191 50 2.82578e-05 252 150 9.24923-> Smoothing ad85001000sis32002_lo.totsky with ad85001000sis32002.totexpo
177 44 4.02198e-05 254 143 9.4861-> Determining extraction radii
190 55 135 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad85001000sis32002.src
The sum of the selected column is 2448144.0 The mean of the selected column is 957.42824 The standard deviation of the selected column is 59.976776 The minimum of selected column is 824.00000 The maximum of selected column is 1065.0000 The number of points used in calculation is 2557-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2286922.0 The mean of the selected column is 894.37700 The standard deviation of the selected column is 68.422707 The minimum of selected column is 760.00000 The maximum of selected column is 1033.0000 The number of points used in calculation is 2557-> Converting (118.0,37.0,2.0) to g2 detector coordinates
The sum of the selected column is 10187.000 The mean of the selected column is 212.22917 The standard deviation of the selected column is 1.0363517 The minimum of selected column is 210.00000 The maximum of selected column is 214.00000 The number of points used in calculation is 48-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 7269.0000 The mean of the selected column is 151.43750 The standard deviation of the selected column is 1.0086066 The minimum of selected column is 150.00000 The maximum of selected column is 153.00000 The number of points used in calculation is 48-> Converting (118.0,37.0,2.0) to g3 detector coordinates
The sum of the selected column is 2993129.0 The mean of the selected column is 177.44421 The standard deviation of the selected column is 18.549603 The minimum of selected column is 140.00000 The maximum of selected column is 217.00000 The number of points used in calculation is 16868-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2501749.0 The mean of the selected column is 148.31332 The standard deviation of the selected column is 27.475753 The minimum of selected column is 77.000000 The maximum of selected column is 209.00000 The number of points used in calculation is 16868-> Removing empty region file ad85001000s032002_0.reg
1 ad85001000s000102h.evt 5029 2 ad85001000s000302m.evt 1460 3 ad85001000s000402m.evt 151 4 ad85001000s000202h.evt 106-> Fetching SIS0_NOTCHIP0.1
1 ad85001000s000112h.evt 5263 2 ad85001000s000312m.evt 1519 3 ad85001000s000412m.evt 156 4 ad85001000s000212h.evt 111-> SIS0_NOTCHIP0.1 already present in current directory
1 ad85001000s100102h.evt 7068 2 ad85001000s100202m.evt 2193-> Fetching SIS1_NOTCHIP0.1
ad85001000s100102h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:54:28 0.14E+05 7068 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100102h.evt
Total Good Bad: Region Time Phase Cut
7068 6009 1059 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7068 6009 1059 0 0 0
in 13899.91 seconds
Spectrum has 6009 counts for 0.4323 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 13900. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.17901 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad85001000s110102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100102h.evt
Total Good Bad: Region Time Phase Cut
7068 6009 1059 0 0 0
Writing events file
6009 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7068 6009 1059 0 0 0
in 13899.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad85001000s110102_1.pi group=yes
Wrote spectrum to ad85001000s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad85001000s110102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 13900. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.17901 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 21 are grouped by a factor 3 ... 22 - 27 are grouped by a factor 2 ... 28 - 67 are single channels ... 68 - 69 are grouped by a factor 2 ... 70 - 71 are single channels ... 72 - 77 are grouped by a factor 2 ... 78 - 78 are single channels ... 79 - 100 are grouped by a factor 2 ... 101 - 103 are grouped by a factor 3 ... 104 - 107 are grouped by a factor 2 ... 108 - 110 are grouped by a factor 3 ... 111 - 116 are grouped by a factor 2 ... 117 - 128 are grouped by a factor 3 ... 129 - 148 are grouped by a factor 4 ... 149 - 153 are grouped by a factor 5 ... 154 - 157 are grouped by a factor 4 ... 158 - 167 are grouped by a factor 5 ... 168 - 173 are grouped by a factor 6 ... 174 - 178 are grouped by a factor 5 ... 179 - 184 are grouped by a factor 6 ... 185 - 204 are grouped by a factor 10 ... 205 - 215 are grouped by a factor 11 ... 216 - 225 are grouped by a factor 10 ... 226 - 236 are grouped by a factor 11 ... 237 - 255 are grouped by a factor 19 ... 256 - 272 are grouped by a factor 17 ... 273 - 331 are grouped by a factor 59 ... 332 - 393 are grouped by a factor 62 ... 394 - 462 are grouped by a factor 69 ... --------------------------------------------- ... ...... exiting, changes written to file : ad85001000s110102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1 2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:54:28 0.14E+05 6009 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/events.tmp
Total Good Bad: Region Time Phase Cut
6009 4759 1250 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6009 4759 1250 0 0 0
in 13899.91 seconds
Spectrum has 4759 counts for 0.3424 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 13900. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.12678 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c1p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Fetching SIS1_NOTCHIP1.1
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:54:28 0.14E+05 6009 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/events.tmp
Total Good Bad: Region Time Phase Cut
6009 1250 4759 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6009 1250 4759 0 0 0
in 13899.91 seconds
Spectrum has 1250 counts for 8.9929E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 13900. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 7.49121E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c2p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf1.tmp 0.791978698618739 rmf2.tmp 0.208021301381261-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
7.920E-01 * rmf1.tmp
2.080E-01 * rmf2.tmp
RMF # 1 : rmf1.tmp 0.79
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf2.tmp 0.21
ASCA SIS1 NONE NONE PI
-> Generating ad85001000s110102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 81 by 78 bins
expanded to 81 by 78 bins
First WMAP bin is at detector pixel 416 656
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 206.28 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.89800E+03
Weighted mean angle from optical axis = 7.427 arcmin
-> SIS1_NOTCHIP0.1 already present in current directoryad85001000s100202m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT MEDIUM 14/02/97 23:51:48 0.48E+04 2193 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100202m.evt
Total Good Bad: Region Time Phase Cut
2193 1862 331 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2193 1862 331 0 0 0
in 4825.27 seconds
Spectrum has 1862 counts for 0.3859 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 4825.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.17901 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad85001000s110202_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100202m.evt
Total Good Bad: Region Time Phase Cut
2193 1862 331 0 0 0
Writing events file
1862 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2193 1862 331 0 0 0
in 4825.27 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s110202.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad85001000s110202_1.pi group=yes
Wrote spectrum to ad85001000s110202_1.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad85001000s110202_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 4825.3 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.17901 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 28 are grouped by a factor 13 ... 29 - 31 are grouped by a factor 3 ... 32 - 37 are grouped by a factor 2 ... 38 - 40 are grouped by a factor 3 ... 41 - 62 are grouped by a factor 2 ... 63 - 65 are grouped by a factor 3 ... 66 - 67 are grouped by a factor 2 ... 68 - 79 are grouped by a factor 4 ... 80 - 84 are grouped by a factor 5 ... 85 - 88 are grouped by a factor 4 ... 89 - 93 are grouped by a factor 5 ... 94 - 111 are grouped by a factor 6 ... 112 - 118 are grouped by a factor 7 ... 119 - 134 are grouped by a factor 8 ... 135 - 154 are grouped by a factor 10 ... 155 - 168 are grouped by a factor 14 ... 169 - 187 are grouped by a factor 19 ... 188 - 211 are grouped by a factor 24 ... 212 - 245 are grouped by a factor 34 ... 246 - 375 are grouped by a factor 130 ... 376 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad85001000s110202_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1 2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT MEDIUM 14/02/97 23:51:48 0.48E+04 1862 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/events.tmp
Total Good Bad: Region Time Phase Cut
1862 1480 382 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1862 1480 382 0 0 0
in 4825.27 seconds
Spectrum has 1480 counts for 0.3067 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 4825.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.12678 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s110202.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> sis1c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP1.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT MEDIUM 14/02/97 23:51:48 0.48E+04 1862 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/events.tmp
Total Good Bad: Region Time Phase Cut
1862 382 1480 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1862 382 1480 0 0 0
in 4825.27 seconds
Spectrum has 382 counts for 7.9167E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 4825.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 7.49121E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s110202.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> sis1c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf1.tmp 0.79484425349087 rmf2.tmp 0.20515574650913-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
7.948E-01 * rmf1.tmp
2.052E-01 * rmf2.tmp
RMF # 1 : rmf1.tmp 0.79
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf2.tmp 0.21
ASCA SIS1 NONE NONE PI
-> Generating ad85001000s110202_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 81 by 78 bins
expanded to 81 by 78 bins
First WMAP bin is at detector pixel 416 656
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 206.28 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.81100E+03
Weighted mean angle from optical axis = 7.382 arcmin
-> Standard Output From STOOL group_event_files:1 ad85001000s100112h.evt 7308 2 ad85001000s100212m.evt 2240-> SIS1_NOTCHIP0.1 already present in current directory
ad85001000s100112h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 HIGH 14/02/97 23:54:28 0.14E+05 7308 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100112h.evt
Total Good Bad: Region Time Phase Cut
7308 6203 1105 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7308 6203 1105 0 0 0
in 13899.91 seconds
Spectrum has 6203 counts for 0.4463 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 13900. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.17901 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad85001000s110312_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100112h.evt
Total Good Bad: Region Time Phase Cut
7308 6203 1105 0 0 0
Writing events file
6203 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7308 6203 1105 0 0 0
in 13899.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s110312.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad85001000s110312_1.pi group=yes
Wrote spectrum to ad85001000s110312_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad85001000s110312_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 13900. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.17901 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 38 are grouped by a factor 6 ... 39 - 43 are grouped by a factor 5 ... 44 - 55 are grouped by a factor 3 ... 56 - 63 are grouped by a factor 2 ... 64 - 64 are single channels ... 65 - 66 are grouped by a factor 2 ... 67 - 68 are single channels ... 69 - 70 are grouped by a factor 2 ... 71 - 100 are single channels ... 101 - 102 are grouped by a factor 2 ... 103 - 103 are single channels ... 104 - 113 are grouped by a factor 2 ... 114 - 114 are single channels ... 115 - 134 are grouped by a factor 2 ... 135 - 137 are grouped by a factor 3 ... 138 - 141 are grouped by a factor 2 ... 142 - 171 are grouped by a factor 3 ... 172 - 175 are grouped by a factor 4 ... 176 - 178 are grouped by a factor 3 ... 179 - 194 are grouped by a factor 4 ... 195 - 200 are grouped by a factor 3 ... 201 - 216 are grouped by a factor 4 ... 217 - 221 are grouped by a factor 5 ... 222 - 225 are grouped by a factor 4 ... 226 - 228 are grouped by a factor 3 ... 229 - 232 are grouped by a factor 4 ... 233 - 242 are grouped by a factor 5 ... 243 - 249 are grouped by a factor 7 ... 250 - 254 are grouped by a factor 5 ... 255 - 260 are grouped by a factor 6 ... 261 - 268 are grouped by a factor 8 ... 269 - 273 are grouped by a factor 5 ... 274 - 280 are grouped by a factor 7 ... 281 - 288 are grouped by a factor 8 ... 289 - 295 are grouped by a factor 7 ... 296 - 304 are grouped by a factor 9 ... 305 - 311 are grouped by a factor 7 ... 312 - 319 are grouped by a factor 8 ... 320 - 330 are grouped by a factor 11 ... 331 - 340 are grouped by a factor 10 ... 341 - 362 are grouped by a factor 11 ... 363 - 376 are grouped by a factor 14 ... 377 - 392 are grouped by a factor 16 ... 393 - 410 are grouped by a factor 18 ... 411 - 431 are grouped by a factor 21 ... 432 - 448 are grouped by a factor 17 ... 449 - 469 are grouped by a factor 21 ... 470 - 503 are grouped by a factor 34 ... 504 - 531 are grouped by a factor 28 ... 532 - 614 are grouped by a factor 83 ... 615 - 723 are grouped by a factor 109 ... 724 - 865 are grouped by a factor 142 ... 866 - 920 are grouped by a factor 55 ... 921 - 943 are grouped by a factor 23 ... --------------------------------------------- ... ...... exiting, changes written to file : ad85001000s110312_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1 2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 HIGH 14/02/97 23:54:28 0.14E+05 6203 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/events.tmp
Total Good Bad: Region Time Phase Cut
6203 4913 1290 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6203 4913 1290 0 0 0
in 13899.91 seconds
Spectrum has 4913 counts for 0.3535 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 13900. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.12678 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s110312.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP1.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 HIGH 14/02/97 23:54:28 0.14E+05 6203 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/events.tmp
Total Good Bad: Region Time Phase Cut
6203 1290 4913 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6203 1290 4913 0 0 0
in 13899.91 seconds
Spectrum has 1290 counts for 9.2806E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 13900. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 7.49121E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s110312.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf1.tmp 0.792036111558923 rmf2.tmp 0.207963888441077-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
7.920E-01 * rmf1.tmp
2.080E-01 * rmf2.tmp
RMF # 1 : rmf1.tmp 0.79
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf2.tmp 0.21
ASCA SIS1 NONE NONE PI
-> Generating ad85001000s110312_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 81 by 78 bins
expanded to 81 by 78 bins
First WMAP bin is at detector pixel 416 656
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 206.28 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.09300E+03
Weighted mean angle from optical axis = 7.429 arcmin
-> SIS1_NOTCHIP0.1 already present in current directoryad85001000s100212m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 MEDIUM 14/02/97 23:51:48 0.48E+04 2240 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100212m.evt
Total Good Bad: Region Time Phase Cut
2240 1897 343 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2240 1897 343 0 0 0
in 4825.27 seconds
Spectrum has 1897 counts for 0.3931 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 4825.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.17901 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad85001000s110412_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100212m.evt
Total Good Bad: Region Time Phase Cut
2240 1897 343 0 0 0
Writing events file
1897 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2240 1897 343 0 0 0
in 4825.27 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000s100212m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s110412.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad85001000s110412_1.pi group=yes
Wrote spectrum to ad85001000s110412_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad85001000s110412_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 4825.3 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.17901 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 55 are grouped by a factor 23 ... 56 - 61 are grouped by a factor 6 ... 62 - 65 are grouped by a factor 4 ... 66 - 70 are grouped by a factor 5 ... 71 - 76 are grouped by a factor 3 ... 77 - 80 are grouped by a factor 4 ... 81 - 83 are grouped by a factor 3 ... 84 - 87 are grouped by a factor 4 ... 88 - 91 are grouped by a factor 2 ... 92 - 100 are grouped by a factor 3 ... 101 - 112 are grouped by a factor 4 ... 113 - 115 are grouped by a factor 3 ... 116 - 120 are grouped by a factor 5 ... 121 - 124 are grouped by a factor 4 ... 125 - 134 are grouped by a factor 5 ... 135 - 141 are grouped by a factor 7 ... 142 - 149 are grouped by a factor 8 ... 150 - 156 are grouped by a factor 7 ... 157 - 167 are grouped by a factor 11 ... 168 - 172 are grouped by a factor 5 ... 173 - 192 are grouped by a factor 10 ... 193 - 205 are grouped by a factor 13 ... 206 - 215 are grouped by a factor 10 ... 216 - 229 are grouped by a factor 14 ... 230 - 253 are grouped by a factor 12 ... 254 - 270 are grouped by a factor 17 ... 271 - 291 are grouped by a factor 21 ... 292 - 309 are grouped by a factor 18 ... 310 - 334 are grouped by a factor 25 ... 335 - 365 are grouped by a factor 31 ... 366 - 409 are grouped by a factor 44 ... 410 - 460 are grouped by a factor 51 ... 461 - 612 are grouped by a factor 152 ... 613 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad85001000s110412_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 1 2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 MEDIUM 14/02/97 23:51:48 0.48E+04 1897 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/events.tmp
Total Good Bad: Region Time Phase Cut
1897 1506 391 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1897 1506 391 0 0 0
in 4825.27 seconds
Spectrum has 1506 counts for 0.3121 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 4825.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.12678 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s110412.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP1.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 MEDIUM 14/02/97 23:51:48 0.48E+04 1897 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/events.tmp
Total Good Bad: Region Time Phase Cut
1897 391 1506 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1897 391 1506 0 0 0
in 4825.27 seconds
Spectrum has 391 counts for 8.1032E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 4825.3 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 7.49121E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s110412.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf1.tmp 0.79388508170796 rmf2.tmp 0.20611491829204-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
7.939E-01 * rmf1.tmp
2.061E-01 * rmf2.tmp
RMF # 1 : rmf1.tmp 0.79
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf2.tmp 0.21
ASCA SIS1 NONE NONE PI
-> Generating ad85001000s110412_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 81 by 78 bins
expanded to 81 by 78 bins
First WMAP bin is at detector pixel 416 656
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 206.28 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.84900E+03
Weighted mean angle from optical axis = 7.364 arcmin
-> Standard Output From STOOL group_event_files:1 ad85001000g200170h.evt 30902 1 ad85001000g200270m.evt 30902 1 ad85001000g200470h.evt 30902-> GIS2_REGION256.4 already present in current directory
ad85001000g200170h.evt ad85001000g200270m.evt ad85001000g200470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21951 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21951 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.54E+04 8162 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21951 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.54E+04 8162 1024
3 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 789 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200170h.evt
Total Good Bad: Region Time Phase Cut
21951 14136 7815 0 0 0
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200270m.evt
Total Good Bad: Region Time Phase Cut
8162 5272 2890 0 0 0
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200470h.evt
Total Good Bad: Region Time Phase Cut
789 512 277 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
30902 19920 10982 0 0 0
in 20556.18 seconds
Spectrum has 19920 counts for 0.9691 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 20556. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.12202 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad85001000g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > read events ad85001000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > read events ad85001000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad85001000g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad85001000g210170_1.pi group=yes
Wrote spectrum to ad85001000g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad85001000g210170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad85001000g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 20556. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.12202 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 23 are grouped by a factor 24 ... 24 - 25 are grouped by a factor 2 ... 26 - 52 are grouped by a factor 3 ... 53 - 66 are grouped by a factor 2 ... 67 - 69 are single channels ... 70 - 71 are grouped by a factor 2 ... 72 - 199 are single channels ... 200 - 201 are grouped by a factor 2 ... 202 - 203 are single channels ... 204 - 205 are grouped by a factor 2 ... 206 - 207 are single channels ... 208 - 209 are grouped by a factor 2 ... 210 - 210 are single channels ... 211 - 212 are grouped by a factor 2 ... 213 - 221 are single channels ... 222 - 223 are grouped by a factor 2 ... 224 - 224 are single channels ... 225 - 230 are grouped by a factor 2 ... 231 - 232 are single channels ... 233 - 234 are grouped by a factor 2 ... 235 - 235 are single channels ... 236 - 239 are grouped by a factor 2 ... 240 - 240 are single channels ... 241 - 246 are grouped by a factor 2 ... 247 - 247 are single channels ... 248 - 251 are grouped by a factor 2 ... 252 - 252 are single channels ... 253 - 254 are grouped by a factor 2 ... 255 - 255 are single channels ... 256 - 321 are grouped by a factor 2 ... 322 - 327 are grouped by a factor 3 ... 328 - 331 are grouped by a factor 2 ... 332 - 334 are grouped by a factor 3 ... 335 - 338 are grouped by a factor 2 ... 339 - 341 are grouped by a factor 3 ... 342 - 343 are grouped by a factor 2 ... 344 - 346 are grouped by a factor 3 ... 347 - 348 are grouped by a factor 2 ... 349 - 351 are grouped by a factor 3 ... 352 - 355 are grouped by a factor 2 ... 356 - 361 are grouped by a factor 3 ... 362 - 363 are grouped by a factor 2 ... 364 - 366 are grouped by a factor 3 ... 367 - 370 are grouped by a factor 2 ... 371 - 376 are grouped by a factor 3 ... 377 - 380 are grouped by a factor 4 ... 381 - 389 are grouped by a factor 3 ... 390 - 391 are grouped by a factor 2 ... 392 - 418 are grouped by a factor 3 ... 419 - 422 are grouped by a factor 4 ... 423 - 425 are grouped by a factor 3 ... 426 - 429 are grouped by a factor 4 ... 430 - 432 are grouped by a factor 3 ... 433 - 444 are grouped by a factor 4 ... 445 - 449 are grouped by a factor 5 ... 450 - 452 are grouped by a factor 3 ... 453 - 456 are grouped by a factor 4 ... 457 - 461 are grouped by a factor 5 ... 462 - 477 are grouped by a factor 4 ... 478 - 502 are grouped by a factor 5 ... 503 - 508 are grouped by a factor 6 ... 509 - 518 are grouped by a factor 5 ... 519 - 530 are grouped by a factor 6 ... 531 - 538 are grouped by a factor 8 ... 539 - 544 are grouped by a factor 6 ... 545 - 549 are grouped by a factor 5 ... 550 - 553 are grouped by a factor 4 ... 554 - 558 are grouped by a factor 5 ... 559 - 570 are grouped by a factor 6 ... 571 - 577 are grouped by a factor 7 ... 578 - 593 are grouped by a factor 8 ... 594 - 606 are grouped by a factor 13 ... 607 - 620 are grouped by a factor 14 ... 621 - 630 are grouped by a factor 10 ... 631 - 641 are grouped by a factor 11 ... 642 - 654 are grouped by a factor 13 ... 655 - 666 are grouped by a factor 12 ... 667 - 679 are grouped by a factor 13 ... 680 - 698 are grouped by a factor 19 ... 699 - 714 are grouped by a factor 16 ... 715 - 748 are grouped by a factor 34 ... 749 - 780 are grouped by a factor 32 ... 781 - 817 are grouped by a factor 37 ... 818 - 863 are grouped by a factor 46 ... 864 - 918 are grouped by a factor 55 ... 919 - 981 are grouped by a factor 63 ... 982 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad85001000g210170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 85 by 129 bins
expanded to 128 by 256 bins
First WMAP bin is at detector pixel 113 11
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 482.30 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.99200E+04
Weighted mean angle from optical axis = 13.852 arcmin
-> Standard Output From STOOL group_event_files:1 ad85001000g300170h.evt 30857 1 ad85001000g300270m.evt 30857 1 ad85001000g300470h.evt 30857-> GIS3_REGION256.4 already present in current directory
ad85001000g300170h.evt ad85001000g300270m.evt ad85001000g300470h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21923 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21923 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.54E+04 8174 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21923 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.54E+04 8174 1024
3 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 760 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300170h.evt
Total Good Bad: Region Time Phase Cut
21923 17007 4916 0 0 0
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300270m.evt
Total Good Bad: Region Time Phase Cut
8174 6365 1809 0 0 0
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300470h.evt
Total Good Bad: Region Time Phase Cut
760 601 159 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
30857 23973 6884 0 0 0
in 20550.18 seconds
Spectrum has 23973 counts for 1.167 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 20550. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.19769 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad85001000g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > read events ad85001000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > read events ad85001000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad85001000g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad85001000g310170_1.pi group=yes
Wrote spectrum to ad85001000g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad85001000g310170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad85001000g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 20550. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.19769 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 22 are grouped by a factor 23 ... 23 - 30 are grouped by a factor 2 ... 31 - 33 are grouped by a factor 3 ... 34 - 37 are grouped by a factor 2 ... 38 - 40 are grouped by a factor 3 ... 41 - 46 are grouped by a factor 2 ... 47 - 49 are grouped by a factor 3 ... 50 - 65 are grouped by a factor 2 ... 66 - 218 are single channels ... 219 - 220 are grouped by a factor 2 ... 221 - 240 are single channels ... 241 - 244 are grouped by a factor 2 ... 245 - 252 are single channels ... 253 - 254 are grouped by a factor 2 ... 255 - 256 are single channels ... 257 - 260 are grouped by a factor 2 ... 261 - 261 are single channels ... 262 - 263 are grouped by a factor 2 ... 264 - 265 are single channels ... 266 - 269 are grouped by a factor 2 ... 270 - 274 are single channels ... 275 - 276 are grouped by a factor 2 ... 277 - 278 are single channels ... 279 - 286 are grouped by a factor 2 ... 287 - 287 are single channels ... 288 - 291 are grouped by a factor 2 ... 292 - 293 are single channels ... 294 - 299 are grouped by a factor 2 ... 300 - 300 are single channels ... 301 - 304 are grouped by a factor 2 ... 305 - 305 are single channels ... 306 - 349 are grouped by a factor 2 ... 350 - 352 are grouped by a factor 3 ... 353 - 358 are grouped by a factor 2 ... 359 - 364 are grouped by a factor 3 ... 365 - 368 are grouped by a factor 2 ... 369 - 371 are grouped by a factor 3 ... 372 - 373 are grouped by a factor 2 ... 374 - 382 are grouped by a factor 3 ... 383 - 384 are grouped by a factor 2 ... 385 - 387 are grouped by a factor 3 ... 388 - 389 are grouped by a factor 2 ... 390 - 392 are grouped by a factor 3 ... 393 - 394 are grouped by a factor 2 ... 395 - 397 are grouped by a factor 3 ... 398 - 401 are grouped by a factor 2 ... 402 - 407 are grouped by a factor 3 ... 408 - 411 are grouped by a factor 2 ... 412 - 414 are grouped by a factor 3 ... 415 - 416 are grouped by a factor 2 ... 417 - 440 are grouped by a factor 3 ... 441 - 444 are grouped by a factor 4 ... 445 - 447 are grouped by a factor 3 ... 448 - 455 are grouped by a factor 4 ... 456 - 460 are grouped by a factor 5 ... 461 - 463 are grouped by a factor 3 ... 464 - 468 are grouped by a factor 5 ... 469 - 471 are grouped by a factor 3 ... 472 - 495 are grouped by a factor 4 ... 496 - 498 are grouped by a factor 3 ... 499 - 503 are grouped by a factor 5 ... 504 - 509 are grouped by a factor 6 ... 510 - 514 are grouped by a factor 5 ... 515 - 522 are grouped by a factor 4 ... 523 - 527 are grouped by a factor 5 ... 528 - 534 are grouped by a factor 7 ... 535 - 538 are grouped by a factor 4 ... 539 - 544 are grouped by a factor 6 ... 545 - 552 are grouped by a factor 4 ... 553 - 557 are grouped by a factor 5 ... 558 - 569 are grouped by a factor 6 ... 570 - 574 are grouped by a factor 5 ... 575 - 580 are grouped by a factor 6 ... 581 - 596 are grouped by a factor 8 ... 597 - 605 are grouped by a factor 9 ... 606 - 613 are grouped by a factor 8 ... 614 - 624 are grouped by a factor 11 ... 625 - 632 are grouped by a factor 8 ... 633 - 646 are grouped by a factor 14 ... 647 - 657 are grouped by a factor 11 ... 658 - 670 are grouped by a factor 13 ... 671 - 684 are grouped by a factor 14 ... 685 - 693 are grouped by a factor 9 ... 694 - 704 are grouped by a factor 11 ... 705 - 717 are grouped by a factor 13 ... 718 - 735 are grouped by a factor 18 ... 736 - 761 are grouped by a factor 26 ... 762 - 784 are grouped by a factor 23 ... 785 - 811 are grouped by a factor 27 ... 812 - 850 are grouped by a factor 39 ... 851 - 890 are grouped by a factor 40 ... 891 - 931 are grouped by a factor 41 ... 932 - 978 are grouped by a factor 47 ... 979 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad85001000g310170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 120 by 148 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 31 16
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 781.37 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 2.39730E+04
Weighted mean angle from optical axis = 14.389 arcmin
-> Plotting ad85001000g210170_1_pi.ps from ad85001000g210170_1.pi
XSPEC 9.01 17:57:27 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad85001000g210170_1.pi
Net count rate (cts/s) for file 1 0.9691 +/- 6.8705E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad85001000g310170_1_pi.ps from ad85001000g310170_1.pi
XSPEC 9.01 17:57:40 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad85001000g310170_1.pi
Net count rate (cts/s) for file 1 1.167 +/- 7.5397E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad85001000s110102_1_pi.ps from ad85001000s110102_1.pi
XSPEC 9.01 17:57:50 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad85001000s110102_1.pi
Net count rate (cts/s) for file 1 0.4323 +/- 5.5833E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad85001000s110202_1_pi.ps from ad85001000s110202_1.pi
XSPEC 9.01 17:58:01 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad85001000s110202_1.pi
Net count rate (cts/s) for file 1 0.3859 +/- 9.2751E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad85001000s110312_1_pi.ps from ad85001000s110312_1.pi
XSPEC 9.01 17:58:12 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad85001000s110312_1.pi
Net count rate (cts/s) for file 1 0.4463 +/- 5.6789E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad85001000s110412_1_pi.ps from ad85001000s110412_1.pi
XSPEC 9.01 17:58:24 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad85001000s110412_1.pi
Net count rate (cts/s) for file 1 0.3931 +/- 9.9713E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:54:28 0.14E+05 7068 0110
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:54:28 0.14E+05 7068 0110
2 PERS-NTH BRIGHT MEDIUM 14/02/97 23:51:48 0.48E+04 2193 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100102h.evt
Total Good Bad: Region Time Phase Cut
7068 6183 885 0 0 0
Writing events file
6183 events written to the output file
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100202m.evt
Total Good Bad: Region Time Phase Cut
2193 1918 275 0 0 0
Writing events file
8101 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9261 8101 1160 0 0 0
in 18725.18 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad85001000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad85001000s100002_1.lc with binsize 115.573258167681
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:51:48 0.19E+05 8101 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/events.tmp
Total Good Bad: Region Time Phase Cut
8101 8101 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8101 8101 0 0 0 0
in 18725.18 seconds
Fits light curve has 8101 counts for 0.4326 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT > set binsize 115.573258167681
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad85001000s100002_1.lc
Wrote FITS light curve to file ad85001000s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad85001000s100002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad85001000s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ PERS-NTH_N2 Start Time (d) .... 10493 23:53:00.883
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10494 12:40:28.883
No. of Rows ....... 164 Bin Time (s) ...... 115.6
Right Ascension ... 4.9893E+01 Internal time sys.. Converted to TJD
Declination ....... 4.2126E+01 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 399 Newbins of 115.573 (s)
Intv 1 Start10493 23:53:58
Ser.1 Avg 0.4332 Chisq 187.7 Var 0.4567E-02 Newbs. 164
Min 0.2769 Max 0.5884 expVar 0.3990E-02 Bins 164
Results from Statistical Analysis
Newbin Integration Time (s).. 115.57
Interval Duration (s)........ 43224.
No. of Newbins .............. 164
Average (c/s) ............... 0.43324 +/- 0.49E-02
Standard Deviation (c/s)..... 0.67577E-01
Minimum (c/s)................ 0.27688
Maximum (c/s)................ 0.58837
Variance ((c/s)**2).......... 0.45666E-02 +/- 0.51E-03
Expected Variance ((c/s)**2). 0.39897E-02 +/- 0.44E-03
Third Moment ((c/s)**3)...... 0.77132E-05
Average Deviation (c/s)...... 0.55685E-01
Skewness..................... 0.24995E-01 +/- 0.19
Kurtosis.....................-0.67407 +/- 0.38
RMS fractional variation....< 0.68537E-01 (3 sigma)
Chi-Square................... 187.71 dof 163
Chi-Square Prob of constancy. 0.89869E-01 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.73953E-02 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 399 Newbins of 115.573 (s)
Intv 1 Start10493 23:53:58
Ser.1 Avg 0.4332 Chisq 187.7 Var 0.4567E-02 Newbs. 164
Min 0.2769 Max 0.5884 expVar 0.3990E-02 Bins 164
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad85001000g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21951 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21951 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.54E+04 8162 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21951 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.54E+04 8162 1024
3 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 789 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200170h.evt
Total Good Bad: Region Time Phase Cut
21951 14136 7815 0 0 0
Writing events file
14136 events written to the output file
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200270m.evt
Total Good Bad: Region Time Phase Cut
8162 5272 2890 0 0 0
Writing events file
19408 events written to the output file
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200470h.evt
Total Good Bad: Region Time Phase Cut
789 512 277 0 0 0
Writing events file
19920 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
30902 19920 10982 0 0 0
in 20556.18 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > read events ad85001000g200270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > read events ad85001000g200470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > filter region ad85001000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad85001000g200070_1.lc with binsize 51.5968332392908
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:51:56 0.21E+05 19920 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/events.tmp
Total Good Bad: Region Time Phase Cut
19920 19920 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
19920 19920 0 0 0 0
in 20556.18 seconds
Fits light curve has 19920 counts for 0.9691 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > set binsize 51.5968332392908
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad85001000g200070_1.lc
Wrote FITS light curve to file ad85001000g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad85001000g200070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad85001000g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ PERS-NTH_N2 Start Time (d) .... 10493 23:52:28.883
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10494 11:56:44.883
No. of Rows ....... 396 Bin Time (s) ...... 51.60
Right Ascension ... 4.9893E+01 Internal time sys.. Converted to TJD
Declination ....... 4.2126E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 84.9746 (s)
Intv 1 Start10493 23:53:11
Ser.1 Avg 0.9695 Chisq 203.2 Var 0.1229E-01 Newbs. 245
Min 0.6590 Max 1.299 expVar 0.1325E-01 Bins 396
Results from Statistical Analysis
Newbin Integration Time (s).. 84.975
Interval Duration (s)........ 43337.
No. of Newbins .............. 245
Average (c/s) ............... 0.96949 +/- 0.74E-02
Standard Deviation (c/s)..... 0.11086
Minimum (c/s)................ 0.65896
Maximum (c/s)................ 1.2985
Variance ((c/s)**2).......... 0.12291E-01 +/- 0.11E-02
Expected Variance ((c/s)**2). 0.13252E-01 +/- 0.12E-02
Third Moment ((c/s)**3)...... 0.22405E-03
Average Deviation (c/s)...... 0.86229E-01
Skewness..................... 0.16443 +/- 0.16
Kurtosis..................... 0.31340 +/- 0.31
RMS fractional variation....< 0.71851E-01 (3 sigma)
Chi-Square................... 203.17 dof 244
Chi-Square Prob of constancy. 0.97333 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.11300 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 84.9746 (s)
Intv 1 Start10493 23:53:11
Ser.1 Avg 0.9695 Chisq 203.2 Var 0.1229E-01 Newbs. 245
Min 0.6590 Max 1.299 expVar 0.1325E-01 Bins 396
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad85001000g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21923 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21923 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.54E+04 8174 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21923 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.54E+04 8174 1024
3 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 760 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300170h.evt
Total Good Bad: Region Time Phase Cut
21923 17007 4916 0 0 0
Writing events file
17007 events written to the output file
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300270m.evt
Total Good Bad: Region Time Phase Cut
8174 6365 1809 0 0 0
Writing events file
23372 events written to the output file
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300470h.evt
Total Good Bad: Region Time Phase Cut
760 601 159 0 0 0
Writing events file
23973 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
30857 23973 6884 0 0 0
in 20550.18 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > read events ad85001000g300270m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > read events ad85001000g300470h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > filter region ad85001000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad85001000g300070_1.lc with binsize 42.8610903541269
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:51:56 0.21E+05 23973 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/events.tmp
Total Good Bad: Region Time Phase Cut
23973 23973 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
23973 23973 0 0 0 0
in 20550.18 seconds
Fits light curve has 23973 counts for 1.167 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > set binsize 42.8610903541269
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad85001000g300070_1.lc
Wrote FITS light curve to file ad85001000g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad85001000g300070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad85001000g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ PERS-NTH_N2 Start Time (d) .... 10493 23:52:28.883
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10494 11:56:44.883
No. of Rows ....... 481 Bin Time (s) ...... 42.86
Right Ascension ... 4.9893E+01 Internal time sys.. Converted to TJD
Declination ....... 4.2126E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 84.9746 (s)
Intv 1 Start10493 23:53:11
Ser.1 Avg 1.166 Chisq 216.4 Var 0.1449E-01 Newbs. 249
Min 0.7816 Max 1.601 expVar 0.1504E-01 Bins 481
Results from Statistical Analysis
Newbin Integration Time (s).. 84.975
Interval Duration (s)........ 43422.
No. of Newbins .............. 249
Average (c/s) ............... 1.1665 +/- 0.78E-02
Standard Deviation (c/s)..... 0.12038
Minimum (c/s)................ 0.78159
Maximum (c/s)................ 1.6006
Variance ((c/s)**2).......... 0.14491E-01 +/- 0.13E-02
Expected Variance ((c/s)**2). 0.15045E-01 +/- 0.14E-02
Third Moment ((c/s)**3)...... 0.38684E-03
Average Deviation (c/s)...... 0.93469E-01
Skewness..................... 0.22176 +/- 0.16
Kurtosis..................... 0.63496 +/- 0.31
RMS fractional variation....< 0.60196E-01 (3 sigma)
Chi-Square................... 216.44 dof 248
Chi-Square Prob of constancy. 0.92670 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.17740E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 84.9746 (s)
Intv 1 Start10493 23:53:11
Ser.1 Avg 1.166 Chisq 216.4 Var 0.1449E-01 Newbs. 249
Min 0.7816 Max 1.601 expVar 0.1504E-01 Bins 481
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad85001000g200170h.evt[2] ad85001000g200270m.evt[2] ad85001000g200470h.evt[2]-> Making L1 light curve of ft970214_2351_1240G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 47592 output records from 47615 good input G2_L1 records.-> Making L1 light curve of ft970214_2351_1240G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 20123 output records from 52907 good input G2_L1 records.-> Merging GTIs from the following files:
ad85001000g300170h.evt[2] ad85001000g300270m.evt[2] ad85001000g300470h.evt[2]-> Making L1 light curve of ft970214_2351_1240G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 45119 output records from 45141 good input G3_L1 records.-> Making L1 light curve of ft970214_2351_1240G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 20007 output records from 50409 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21951 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200170h.evt
Total Good Bad: Region Time Phase Cut
21951 14136 7815 0 0 0
Writing events file
14136 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21951 14136 7815 0 0 0
in 14629.98 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > filter region ad85001000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad85001000g200170h_1.ulc use_events=yes
Wrote events list to file ad85001000g200170h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad85001000g200270m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.54E+04 8162 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200270m.evt
Total Good Bad: Region Time Phase Cut
8162 5272 2890 0 0 0
Writing events file
5272 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8162 5272 2890 0 0 0
in 5424.20 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000g200270m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > filter region ad85001000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad85001000g200270m_1.ulc use_events=yes
Wrote events list to file ad85001000g200270m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad85001000g200470h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 789 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200470h.evt
Total Good Bad: Region Time Phase Cut
789 512 277 0 0 0
Writing events file
512 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
789 512 277 0 0 0
in 502.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000g200470h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > filter region ad85001000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad85001000g200470h_1.ulc use_events=yes
Wrote events list to file ad85001000g200470h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad85001000g300170h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.15E+05 21923 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300170h.evt
Total Good Bad: Region Time Phase Cut
21923 17007 4916 0 0 0
Writing events file
17007 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
21923 17007 4916 0 0 0
in 14623.98 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > filter region ad85001000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad85001000g300170h_1.ulc use_events=yes
Wrote events list to file ad85001000g300170h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad85001000g300270m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.54E+04 8174 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300270m.evt
Total Good Bad: Region Time Phase Cut
8174 6365 1809 0 0 0
Writing events file
6365 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8174 6365 1809 0 0 0
in 5424.20 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000g300270m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > filter region ad85001000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad85001000g300270m_1.ulc use_events=yes
Wrote events list to file ad85001000g300270m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad85001000g300470h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 760 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300470h.evt
Total Good Bad: Region Time Phase Cut
760 601 159 0 0 0
Writing events file
601 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
760 601 159 0 0 0
in 502.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000g300470h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > filter region ad85001000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad85001000g300470h_1.ulc use_events=yes
Wrote events list to file ad85001000g300470h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Skipping ad85001000s000102h_1.ulc since ad85001000s032002_1.reg does not exist
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:54:28 0.14E+05 7068 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100102h.evt
Total Good Bad: Region Time Phase Cut
7068 6183 885 0 0 0
Writing events file
6183 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7068 6183 885 0 0 0
in 13899.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad85001000s100102h_1.ulc use_events=yes
Wrote events list to file ad85001000s100102h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad85001000s100112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 HIGH 14/02/97 23:54:28 0.14E+05 7308 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100112h.evt
Total Good Bad: Region Time Phase Cut
7308 6384 924 0 0 0
Writing events file
6384 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7308 6384 924 0 0 0
in 13899.91 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad85001000s100112h_1.ulc use_events=yes
Wrote events list to file ad85001000s100112h_1.ulc
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad85001000s100202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT MEDIUM 14/02/97 23:51:48 0.48E+04 2193 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100202m.evt
Total Good Bad: Region Time Phase Cut
2193 1918 275 0 0 0
Writing events file
1918 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2193 1918 275 0 0 0
in 4825.27 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad85001000s100202m_1.ulc use_events=yes
Wrote events list to file ad85001000s100202m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad85001000s100212m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 MEDIUM 14/02/97 23:51:48 0.48E+04 2240 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100212m.evt
Total Good Bad: Region Time Phase Cut
2240 1957 283 0 0 0
Writing events file
1957 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2240 1957 283 0 0 0
in 4825.27 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000s100212m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad85001000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad85001000s100212m_1.ulc use_events=yes
Wrote events list to file ad85001000s100212m_1.ulc
Changing Data directory from:
/data/data24/seq_proc/85001000.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 10204 Total of 0 sets of frame data are extracted.
1 ad85001000g200170h.unf 54850 1 ad85001000g200270m.unf 54850 1 ad85001000g200370l.unf 54850 1 ad85001000g200470h.unf 54850-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 37626 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 37626 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.57E+04 13711 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 37626 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.57E+04 13711 1024
3 PERS-NTH PH LOW 15/02/97 02:46:52 0.31E+04 2258 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 37626 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.57E+04 13711 1024
3 PERS-NTH PH LOW 15/02/97 02:46:52 0.31E+04 2258 1024
4 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 1255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200170h.unf
Total Good Bad: Region Time Phase Cut
37626 3919 33707 0 0 0
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200270m.unf
Total Good Bad: Region Time Phase Cut
13711 1369 12342 0 0 0
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200370l.unf
Total Good Bad: Region Time Phase Cut
2258 504 1754 0 0 0
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200470h.unf
Total Good Bad: Region Time Phase Cut
1255 128 1127 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
54850 5920 48930 0 0 0
in 24939.92 seconds
Spectrum has 5920 counts for 0.2374 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 24940. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad85001000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > read events ad85001000g200270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > read events ad85001000g200370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > read events ad85001000g200470h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad85001000g220170.cal group=yes
Wrote spectrum to ad85001000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 18:13:26 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad85001000g220170.cal
Net count rate (cts/s) for file 1 0.2374 +/- 3.0882E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 9.7511E+05 using 84 PHA bins.
Reduced chi-squared = 1.2664E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 9.6709E+05 using 84 PHA bins.
Reduced chi-squared = 1.2399E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 9.6709E+05 using 84 PHA bins.
Reduced chi-squared = 1.2242E+04
!XSPEC> renorm
Chi-Squared = 1489. using 84 PHA bins.
Reduced chi-squared = 18.85
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
1182.8 0 1.000 5.892 0.1174 5.0747E-02
4.4345E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
567.74 0 1.000 5.858 0.1709 7.7273E-02
3.9549E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
329.20 -1 1.000 5.912 0.1934 0.1097
2.6224E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
300.03 -2 1.000 5.969 0.2268 0.1272
1.3995E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
295.51 -3 1.000 5.945 0.2069 0.1220
1.9066E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
294.86 -4 1.000 5.955 0.2141 0.1246
1.6442E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
294.53 -5 1.000 5.950 0.2098 0.1233
1.7661E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
294.51 -1 1.000 5.952 0.2107 0.1236
1.7310E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
294.51 0 1.000 5.952 0.2107 0.1236
1.7310E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.95151 +/- 0.95153E-02
3 3 2 gaussian/b Sigma 0.210745 +/- 0.97593E-02
4 4 2 gaussian/b norm 0.123649 +/- 0.29889E-02
5 2 3 gaussian/b LineE 6.55264 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.221132 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.730963E-02 +/- 0.21282E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 294.5 using 84 PHA bins.
Reduced chi-squared = 3.728
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad85001000g220170.cal peaks at 5.95151 +/- 0.0095153 keV1 ad85001000g300170h.unf 50562 1 ad85001000g300270m.unf 50562 1 ad85001000g300370l.unf 50562 1 ad85001000g300470h.unf 50562-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 34721 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 34721 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.57E+04 12681 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 34721 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.57E+04 12681 1024
3 PERS-NTH PH LOW 15/02/97 02:46:52 0.31E+04 1995 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 34721 1024
2 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.57E+04 12681 1024
3 PERS-NTH PH LOW 15/02/97 02:46:52 0.31E+04 1995 1024
4 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 1165 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300170h.unf
Total Good Bad: Region Time Phase Cut
34721 3644 31077 0 0 0
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300270m.unf
Total Good Bad: Region Time Phase Cut
12681 1331 11350 0 0 0
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300370l.unf
Total Good Bad: Region Time Phase Cut
1995 455 1540 0 0 0
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300470h.unf
Total Good Bad: Region Time Phase Cut
1165 124 1041 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
50562 5554 45008 0 0 0
in 24931.92 seconds
Spectrum has 5554 counts for 0.2228 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 24932. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad85001000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!xsel:ASCA > read events ad85001000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > read events ad85001000g300270m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > read events ad85001000g300370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > read events ad85001000g300470h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad85001000g320170.cal group=yes
Wrote spectrum to ad85001000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 18:14:25 4-Jun-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad85001000g320170.cal
Net count rate (cts/s) for file 1 0.2228 +/- 2.9945E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.0888E+06 using 84 PHA bins.
Reduced chi-squared = 1.4141E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.0818E+06 using 84 PHA bins.
Reduced chi-squared = 1.3869E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.0818E+06 using 84 PHA bins.
Reduced chi-squared = 1.3694E+04
!XSPEC> renorm
Chi-Squared = 1440. using 84 PHA bins.
Reduced chi-squared = 18.23
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
1187.5 0 1.000 5.893 9.4350E-02 4.6501E-02
3.9912E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
567.06 0 1.000 5.869 0.1400 7.3301E-02
3.4120E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
314.34 -1 1.000 5.920 0.1522 0.1051
2.1254E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
305.38 -2 1.000 5.929 0.1506 0.1113
1.8234E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
304.89 -3 1.000 5.925 0.1459 0.1106
1.8918E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
304.87 -4 1.000 5.926 0.1462 0.1108
1.8730E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
304.86 -5 1.000 5.926 0.1459 0.1108
1.8777E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
304.86 0 1.000 5.926 0.1459 0.1108
1.8775E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.92572 +/- 0.72369E-02
3 3 2 gaussian/b Sigma 0.145915 +/- 0.92325E-02
4 4 2 gaussian/b norm 0.110795 +/- 0.24987E-02
5 2 3 gaussian/b LineE 6.52424 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.153107 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.877491E-02 +/- 0.15598E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 304.9 using 84 PHA bins.
Reduced chi-squared = 3.859
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad85001000g320170.cal peaks at 5.92572 +/- 0.0072369 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:54:28 0.16E+05 129416 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000102h.unf
Total Good Bad: Region Time Phase Cut
129416 6745 0 122671 0 0
Writing events file
6745 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
129416 6745 0 122671 0 0
in 931.63 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad85001000s000102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad85001000s000102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6745
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 46 3181
Flickering pixels iter, pixels & cnts : 1 21 227
cleaning chip # 2
Hot pixels & counts : 34 2641
Flickering pixels iter, pixels & cnts : 1 17 156
cleaning chip # 3
Number of pixels rejected : 118
Number of (internal) image counts : 6745
Number of image cts rejected (N, %) : 6205 91.9940720
By chip : 0 1 2 3
Pixels rejected : 0 67 51 0
Image counts : 0 3686 3059 0
Image cts rejected: 0 3408 2797 0
Image cts rej (%) : 0.00 92.46 91.44 0.00
filtering data...
Total counts : 0 3686 3059 0
Total cts rejected: 0 3408 2797 0
Total cts rej (%) : 0.00 92.46 91.44 0.00
Number of clean counts accepted : 540
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 118
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad85001000s000112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT2 HIGH 14/02/97 23:54:28 0.16E+05 130157 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000112h.unf
Total Good Bad: Region Time Phase Cut
130157 6823 0 123334 0 0
Writing events file
6823 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
130157 6823 0 123334 0 0
in 931.63 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad85001000s000112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad85001000s000112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6823
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 46 3183
Flickering pixels iter, pixels & cnts : 1 21 228
cleaning chip # 2
Hot pixels & counts : 34 2644
Flickering pixels iter, pixels & cnts : 1 17 156
cleaning chip # 3
Number of pixels rejected : 118
Number of (internal) image counts : 6823
Number of image cts rejected (N, %) : 6211 91.0303421
By chip : 0 1 2 3
Pixels rejected : 0 67 51 0
Image counts : 0 3729 3094 0
Image cts rejected: 0 3411 2800 0
Image cts rej (%) : 0.00 91.47 90.50 0.00
filtering data...
Total counts : 0 3729 3094 0
Total cts rejected: 0 3411 2800 0
Total cts rej (%) : 0.00 91.47 90.50 0.00
Number of clean counts accepted : 612
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 118
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad85001000s000202h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT HIGH 15/02/97 06:02:48 0.20E+04 11677 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/ad85001000s000202h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad85001000s000202h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT2 HIGH 15/02/97 06:02:48 0.20E+04 11831 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/ad85001000s000212h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad85001000s000212h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT MEDIUM 15/02/97 03:05:56 0.51E+04 4484 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000302m.unf
Total Good Bad: Region Time Phase Cut
4484 36 0 4448 0 0
Writing events file
36 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4484 36 0 4448 0 0
in 35.36 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s000302m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad85001000s000302m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad85001000s000302m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 36
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 2 8
cleaning chip # 2
Hot pixels & counts : 1 3
cleaning chip # 3
Number of pixels rejected : 3
Number of (internal) image counts : 36
Number of image cts rejected (N, %) : 11 30.5555553
By chip : 0 1 2 3
Pixels rejected : 0 2 1 0
Image counts : 0 12 24 0
Image cts rejected: 0 8 3 0
Image cts rej (%) : 0.00 66.67 12.50 0.00
filtering data...
Total counts : 0 12 24 0
Total cts rejected: 0 8 3 0
Total cts rej (%) : 0.00 66.67 12.50 0.00
Number of clean counts accepted : 25
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 3
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad85001000s000312m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT2 MEDIUM 15/02/97 03:05:56 0.51E+04 4597 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s000312m.unf
Total Good Bad: Region Time Phase Cut
4597 37 0 4560 0 0
Writing events file
37 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4597 37 0 4560 0 0
in 35.36 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s000312m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad85001000s000312m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad85001000s000312m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 37
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 2 8
cleaning chip # 2
Hot pixels & counts : 1 3
cleaning chip # 3
Number of pixels rejected : 3
Number of (internal) image counts : 37
Number of image cts rejected (N, %) : 11 29.7297306
By chip : 0 1 2 3
Pixels rejected : 0 2 1 0
Image counts : 0 13 24 0
Image cts rejected: 0 8 3 0
Image cts rej (%) : 0.00 61.54 12.50 0.00
filtering data...
Total counts : 0 13 24 0
Total cts rejected: 0 8 3 0
Total cts rej (%) : 0.00 61.54 12.50 0.00
Number of clean counts accepted : 26
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 3
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad85001000s000402m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT MEDIUM 14/02/97 23:51:48 0.18E+04 1903 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/ad85001000s000402m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s000402m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad85001000s000402m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 PERS-NTH BRIGHT2 MEDIUM 14/02/97 23:51:48 0.18E+04 1954 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/ad85001000s000412m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s000412m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad85001000s000412m.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT HIGH 14/02/97 23:54:28 0.18E+05 275837 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100102h.unf
Total Good Bad: Region Time Phase Cut
275837 12976 0 262861 0 0
Writing events file
12976 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
275837 12976 0 262861 0 0
in 935.63 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad85001000s100102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad85001000s100102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 12976
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 76 6538
Flickering pixels iter, pixels & cnts : 1 34 383
cleaning chip # 2
Hot pixels & counts : 62 5109
Flickering pixels iter, pixels & cnts : 1 38 408
cleaning chip # 3
Number of pixels rejected : 210
Number of (internal) image counts : 12976
Number of image cts rejected (N, %) : 12438 95.8538818
By chip : 0 1 2 3
Pixels rejected : 0 110 100 0
Image counts : 0 7190 5786 0
Image cts rejected: 0 6921 5517 0
Image cts rej (%) : 0.00 96.26 95.35 0.00
filtering data...
Total counts : 0 7190 5786 0
Total cts rejected: 0 6921 5517 0
Total cts rej (%) : 0.00 96.26 95.35 0.00
Number of clean counts accepted : 538
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 210
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad85001000s100112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 HIGH 14/02/97 23:54:28 0.18E+05 276718 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100112h.unf
Total Good Bad: Region Time Phase Cut
276718 13074 0 263644 0 0
Writing events file
13074 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
276718 13074 0 263644 0 0
in 935.63 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad85001000s100112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad85001000s100112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 13074
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 76 6548
Flickering pixels iter, pixels & cnts : 1 34 385
cleaning chip # 2
Hot pixels & counts : 62 5115
Flickering pixels iter, pixels & cnts : 1 38 410
cleaning chip # 3
Number of pixels rejected : 210
Number of (internal) image counts : 13074
Number of image cts rejected (N, %) : 12458 95.2883606
By chip : 0 1 2 3
Pixels rejected : 0 110 100 0
Image counts : 0 7238 5836 0
Image cts rejected: 0 6933 5525 0
Image cts rej (%) : 0.00 95.79 94.67 0.00
filtering data...
Total counts : 0 7238 5836 0
Total cts rejected: 0 6933 5525 0
Total cts rej (%) : 0.00 95.79 94.67 0.00
Number of clean counts accepted : 616
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 210
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad85001000s100202m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT MEDIUM 14/02/97 23:51:48 0.69E+04 18462 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100202m.unf
Total Good Bad: Region Time Phase Cut
18462 102 0 18360 0 0
Writing events file
102 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
18462 102 0 18360 0 0
in 35.36 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad85001000s100202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad85001000s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 102
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 8 32
Flickering pixels iter, pixels & cnts : 1 2 6
cleaning chip # 2
Hot pixels & counts : 3 12
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 3
Number of pixels rejected : 14
Number of (internal) image counts : 102
Number of image cts rejected (N, %) : 53 51.9607849
By chip : 0 1 2 3
Pixels rejected : 0 10 4 0
Image counts : 0 51 51 0
Image cts rejected: 0 38 15 0
Image cts rej (%) : 0.00 74.51 29.41 0.00
filtering data...
Total counts : 0 51 51 0
Total cts rejected: 0 38 15 0
Total cts rej (%) : 0.00 74.51 29.41 0.00
Number of clean counts accepted : 49
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 14
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad85001000s100212m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 MEDIUM 14/02/97 23:51:48 0.69E+04 18552 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100212m.unf
Total Good Bad: Region Time Phase Cut
18552 103 0 18449 0 0
Writing events file
103 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
18552 103 0 18449 0 0
in 35.36 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s100212m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad85001000s100212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad85001000s100212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 103
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 8 32
Flickering pixels iter, pixels & cnts : 1 2 6
cleaning chip # 2
Hot pixels & counts : 3 12
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 3
Number of pixels rejected : 14
Number of (internal) image counts : 103
Number of image cts rejected (N, %) : 53 51.4563103
By chip : 0 1 2 3
Pixels rejected : 0 10 4 0
Image counts : 0 51 52 0
Image cts rejected: 0 38 15 0
Image cts rej (%) : 0.00 74.51 28.85 0.00
filtering data...
Total counts : 0 51 52 0
Total cts rejected: 0 38 15 0
Total cts rej (%) : 0.00 74.51 28.85 0.00
Number of clean counts accepted : 50
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 14
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad85001000s100302l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT LOW 15/02/97 02:42:28 0.40E+04 3130 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100302l.unf
Total Good Bad: Region Time Phase Cut
3130 2776 0 354 0 0
Writing events file
2776 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3130 2776 0 354 0 0
in 1949.02 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad85001000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad85001000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 2776
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 12 1417
Flickering pixels iter, pixels & cnts : 1 3 28
cleaning chip # 2
Hot pixels & counts : 9 1250
Flickering pixels iter, pixels & cnts : 1 2 16
cleaning chip # 3
Number of pixels rejected : 26
Number of (internal) image counts : 2776
Number of image cts rejected (N, %) : 2711 97.6585007
By chip : 0 1 2 3
Pixels rejected : 0 15 11 0
Image counts : 0 1471 1305 0
Image cts rejected: 0 1445 1266 0
Image cts rej (%) : 0.00 98.23 97.01 0.00
filtering data...
Total counts : 0 1471 1305 0
Total cts rejected: 0 1445 1266 0
Total cts rej (%) : 0.00 98.23 97.01 0.00
Number of clean counts accepted : 65
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 26
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad85001000s100312l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 PERS-NTH BRIGHT2 LOW 15/02/97 02:42:28 0.40E+04 3145 0110
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000s100312l.unf
Total Good Bad: Region Time Phase Cut
3145 2779 0 366 0 0
Writing events file
2779 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3145 2779 0 366 0 0
in 1949.02 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000s100312l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 8.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad85001000s100312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad85001000s100312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 2779
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 12 1418
Flickering pixels iter, pixels & cnts : 1 3 28
cleaning chip # 2
Hot pixels & counts : 9 1250
Flickering pixels iter, pixels & cnts : 1 2 16
cleaning chip # 3
Number of pixels rejected : 26
Number of (internal) image counts : 2779
Number of image cts rejected (N, %) : 2712 97.5890579
By chip : 0 1 2 3
Pixels rejected : 0 15 11 0
Image counts : 0 1473 1306 0
Image cts rejected: 0 1446 1266 0
Image cts rej (%) : 0.00 98.17 96.94 0.00
filtering data...
Total counts : 0 1473 1306 0
Total cts rejected: 0 1446 1266 0
Total cts rej (%) : 0.00 98.17 96.94 0.00
Number of clean counts accepted : 67
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 26
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad85001000g200170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 37626 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200170h.unf
Total Good Bad: Region Time Phase Cut
37626 283 0 37343 0 0
Writing events file
283 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
37626 283 0 37343 0 0
in 431.82 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad85001000g200170h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 37626 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200170h.unf
Total Good Bad: Region Time Phase Cut
37626 134 0 37492 0 0
Writing events file
134 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
37626 134 0 37492 0 0
in 144.16 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad85001000g200270m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.57E+04 13711 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200270m.unf
Total Good Bad: Region Time Phase Cut
13711 23 0 13688 0 0
Writing events file
23 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13711 23 0 13688 0 0
in 31.86 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad85001000g200270m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.57E+04 13711 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/ad85001000g200270m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g200270m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad85001000g200270m.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH LOW 15/02/97 02:46:52 0.31E+04 2258 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200370l.unf
Total Good Bad: Region Time Phase Cut
2258 1300 0 958 0 0
Writing events file
1300 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2258 1300 0 958 0 0
in 1824.02 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad85001000g200370l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH LOW 15/02/97 02:46:52 0.31E+04 2258 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g200370l.unf
Total Good Bad: Region Time Phase Cut
2258 891 0 1367 0 0
Writing events file
891 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2258 891 0 1367 0 0
in 1151.95 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad85001000g200470h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 1255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/ad85001000g200470h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g200470h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad85001000g200470h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 1255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/ad85001000g200470h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g200470h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad85001000g200470h.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 34721 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300170h.unf
Total Good Bad: Region Time Phase Cut
34721 252 0 34469 0 0
Writing events file
252 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
34721 252 0 34469 0 0
in 431.82 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad85001000g300170h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 14/02/97 23:54:36 0.16E+05 34721 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300170h.unf
Total Good Bad: Region Time Phase Cut
34721 115 0 34606 0 0
Writing events file
115 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
34721 115 0 34606 0 0
in 144.16 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad85001000g300270m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.57E+04 12681 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300270m.unf
Total Good Bad: Region Time Phase Cut
12681 13 0 12668 0 0
Writing events file
13 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12681 13 0 12668 0 0
in 31.86 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad85001000g300270m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH MEDIUM 14/02/97 23:51:56 0.57E+04 12681 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/ad85001000g300270m.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g300270m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad85001000g300270m.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH LOW 15/02/97 02:46:52 0.31E+04 1995 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300370l.unf
Total Good Bad: Region Time Phase Cut
1995 1119 0 876 0 0
Writing events file
1119 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1995 1119 0 876 0 0
in 1824.02 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad85001000g300370l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH LOW 15/02/97 02:46:52 0.31E+04 1995 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data24/seq_proc/85001000.005/ad85001000g300370l.unf
Total Good Bad: Region Time Phase Cut
1995 814 0 1181 0 0
Writing events file
814 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1995 814 0 1181 0 0
in 1151.95 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad85001000g300470h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 1165 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/ad85001000g300470h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g300470h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad85001000g300470h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 PERS-NTH PH HIGH 15/02/97 09:53:20 0.50E+03 1165 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data24/seq_proc/85001000.005/ad85001000g300470h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data24/seq_proc/85001000.005/
Setting mkf directory to /data/data24/seq_proc/85001000.005/
!earthevents:ASCA > read events ad85001000g300470h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data24/seq_proc/85001000.005/
HK Directory is: /data/data24/seq_proc/85001000.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad85001000g300470h.brt since it contains 0 eventsOffset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad85001000s000102h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad85001000s000202h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad85001000s000102h.unf
ad85001000s000302m.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad85001000s000402m.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad85001000s000302m.unf
ad85001000s000112h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad85001000s000212h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad85001000s000112h.unf
ad85001000s000312m.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad85001000s000412m.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad85001000s000312m.unf
ad85001000s000101h.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad85001000s000201h.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad85001000s000101h.unf
ad85001000s000301m.unf|S0_ARENA|0|S0 Area discrimination enable/disable ad85001000s000401m.unf|S0_ARENA|1|S0 Area discrimination enable/disable-> listing ad85001000s000301m.unf
ad85001000s000501l.unf|S0_ARENA|1|S0 Area discrimination enable/disable ad85001000s000601l.unf|S0_ARENA|0|S0 Area discrimination enable/disable-> listing ad85001000s000501l.unf
ad85001000g200170h.unf|CPU2|RUN|CPU2 run/stop ad85001000g200470h.unf|CPU2|STOP|CPU2 run/stop ad85001000g200170h.unf|CPU3|RUN|CPU3 run/stop ad85001000g200470h.unf|CPU3|STOP|CPU3 run/stop-> listing ad85001000g200170h.unf
ad85001000g300170h.unf|CPU2|RUN|CPU2 run/stop ad85001000g300470h.unf|CPU2|STOP|CPU2 run/stop ad85001000g300170h.unf|CPU3|RUN|CPU3 run/stop ad85001000g300470h.unf|CPU3|STOP|CPU3 run/stop-> listing ad85001000g300170h.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files