cje2c3l Version 1.22d Thu Oct  7 15:07:37 PDT 1999

==============================
cje2c3l V047p2 Build Summary
==============================

	Job Start Epoch: 2000-198-07:00:00
	Job Stop Epoch:  2000-198-13:50:06
	Duration of job: 6.8 hours
	Tape change epochs: 0
	Stations:
		'HARTRAO' (grt)
		'MOP' (grt)
		'SESHAN25' (grt)
	Sources:
		'J1405+04'
		'J1127-18'
	Tape ids:
		'CA-3-0074612'
		'ATNF0113'
		'CA-3-0076816'

	Totals: [9] PB_STARTs  [9] PB_STOPS  [3] Tape ids
		[3] PCFS logs   [0] SRT logs


This job was built by ________________ on Wed Sep 13 11:10:58 2000


Number of baselines at build time: 3 ACTUAL: ____________

Total number of lags at build time: 3072 ACTUAL: ____________

Duration of job at build time:  6.8 HRS ACTUAL: _____________


Checked and ready for correlation.

Date: _________________  Person: ________________

===========================
CHECKLIST for job 'V047p2'
===========================

Complete this checklist before running 'makeV047p2'.

[ ] Copy the experiment V047p2.sum file and any additional note files to
    the job's working directory.  If ATNF telescopes are involved, note files
    in the form of <job_name><st>.notes must be downloaded from the ATNF
    server 'ftp.atnf.csiro.au' in the directory
    '/pub/people/vlbi/vsop/logs/<mon><yr>'.  These note files contain
    information ***CRITICAL*** to the correlation of ATNF telescopes.

[ ] Check V047p2.jb for correct parameters (sample rate etc.)
    Check default integration time.

[ ] Check HARTRAO.st for correct parameters...modify if necessary.
    HARTRAO.ev files contain events for ALL channels...modification required
    if pulsar gating is used.  Comment .ev file reference if not required.
    Check pt_type and set Synthetic Autocorrelator parms for best result.

[ ] Add constant station delay to station clock model file HARTRAO_c.smb.
    This must always be >= 0.0.

[ ] Add CALIBRATION and ANTENNA coefficients to HARTRAO.cal -- if required.

[ ] Check MOP.st for correct parameters...modify if necessary.
    MOP.ev files contain events for ALL channels...modification required
    if pulsar gating is used.  Comment .ev file reference if not required.
    Check pt_type and set Synthetic Autocorrelator parms for best result.

[ ] Add GPS clock offset model to station clock model file MOP_c.smb.
    If station time is faster/leading GPS time then it is a (+)'ve delay.

[ ] Add constant station delay to station clock model file MOP_c.smb.
    This must always be >= 0.0.

[ ] Add CALIBRATION and ANTENNA coefficients to MOP.cal -- if required.

[ ] Check SESHAN25.st for correct parameters...modify if necessary.
    SESHAN25.ev files contain events for ALL channels...modification required
    if pulsar gating is used.  Comment .ev file reference if not required.
    Check pt_type and set Synthetic Autocorrelator parms for best result.

[ ] Add GPS clock offset model to station clock model file SESHAN25_c.smb.
    If station time is faster/leading GPS time then it is a (+)'ve delay.

[ ] Add constant station delay to station clock model file SESHAN25_c.smb.
    This must always be >= 0.0.

[ ] Add CALIBRATION and ANTENNA coefficients to SESHAN25.cal -- if required.

[ ] Check V047p2.bs for correct baselines...remove comments if baseline module
    autocorrelation is required.  Check baseline integration times.

[ ] Ensure that SOURCE 'J1405+04' is in ~/smdb/finblokq.dat or in finlocq.dat
    Ensure source coordinates are IDENTICAL to that in the V047p2.sum file.

[ ] Ensure that SOURCE 'J1127-18' is in ~/smdb/finblokq.dat or in finlocq.dat
    Ensure source coordinates are IDENTICAL to that in the V047p2.sum file.

[ ] Update file J1405+04.cal -- if necessary for cc2fits (source coordinates
    are automatically extracted from the V047p2.eg file).

[ ] Update file J1127-18.cal -- if necessary for cc2fits (source coordinates
    are automatically extracted from the V047p2.eg file).

[ ] Check to ensure that ~/smdb/finals.data is up-to-date for this obs.

[ ] When all above checks are complete run 'makeV047p2'.

[ ] Check 'models.out' for any model generation ERRORs or WARNINGs

[ ] 'makeV047p2' ran ok?

[ ] Run 'cc2fits' until BSD file catalogging starts -- to ensure job is FITS
    exportable.

[ ] Create job V047p2 directory on geo (e.g. geod1/V047p2), copy 'cc2fits.control'
    and edit it in preparation for FITS export and raw data archive.

[ ] Job 'V047p2' is ready for correlation.



	================== EXPERIMENT 'V047p2' SUMMARY REPORT ==================

	**** TO BE FILLED IN BY THE PR AND GIVEN TO THE OPERATIONS MANAGER ****

	DATE: _________________ PR: ____________

	================================
	STATION FRINGE DETECTION SUMMARY
	================================

	HARTRAO:
	    [  ] fringes detected                        Comments:
	    Delay corr:  _________ us
	    Delay resid: _________ us    Rate resid: _________ ps/s

	MOP:
	    [  ] fringes detected                        Comments:
	    Delay corr:  _________ us
	    Delay resid: _________ us    Rate resid: _________ ps/s

	SESHAN25:
	    [  ] fringes detected                        Comments:
	    Delay corr:  _________ us
	    Delay resid: _________ us    Rate resid: _________ ps/s

	====================
	DATA RELEASE SUMMARY
	====================

	[ ] RELEASED
	[ ] ABANDONED Reason:

	Release date: _____________________________

	Data volume: ________ FITS files; _______ Gbytes

	Data Shipments: 
	           [  ] PI: ____________________  DAT / Exabyte
	           [  ] U of C:                   Exabyte

	           [  ] Other: _________________  DAT / Exabyte

	Comments: