cje2c3l Version 1.22 Jan. 16 1998 13:14 PST ============================== cje2c3l V050j Build Summary ============================== Job Start Epoch: 1997-352-14:00:00 Job Stop Epoch: 1997-353-03:45:30 Duration of job: 13.8 hours Tape change epochs: 3 Stations: 'NOTO' (grt) 'SESHAN25' (grt) 'VSOP_SC' (srt) 'AT' (grt) 'MOP' (grt) 'USUDA64' (grt) Tracking Stations: 'GBANK_TS' 'TDBIN_TS' Tracking PASSES: 'GBANK_TS' 1997-352-17:44:00 --> 1997-352-21:04:52 'TDBIN_TS' 1997-353-00:10:00 --> 1997-353-03:28:13 Sources: '1147+245' '1156+295' Tape ids: 'CA-3-001350A' 'CA-3-003740F' 'CA-3-0036913' 'CA-3-0014309' 'CA-3-001620A' 'AT-3-002911E' 'AT-3-002921F' 'AT-3-002511A' 'CA-3-003640E' Totals: [17] PB_STARTs [17] PB_STOPS [9] Tape ids [4] PCFS logs [1] SRT logs This job was built by ________________ on Fri Jan 16 16:59:07 1998 Number of baselines at build time: 15 ACTUAL: ____________ Total number of lags at build time: 15360 ACTUAL: ____________ Duration of job at build time: 13.8 HRS ACTUAL: _____________ Checked and ready for correlation. Date: _________________ Person: ________________ =========================== CHECKLIST for job 'V050j' =========================== Complete this checklist before running 'makeV050j'. [ ] Copy the experiment V050j.sum file and any additional note files to the job's working directory [ ] Check V050j.jb for correct parameters (sample rate etc.) Check default integration time. [ ] Ensure that TCF file(s) (*.kcX) for tracking station 'GBANK_TS' are in the job directory for time ranges (yymmddhhmm): 9712181744 to 9712182104. X - d==Goldstone; m==Madrid; t==Tidbinbilla; g==Greenbank; u==Usuda [ ] Ensure that TCF file(s) (*.kcX) for tracking station 'TDBIN_TS' are in the job directory for time ranges (yymmddhhmm): 9712190010 to 9712190328. X - d==Goldstone; m==Madrid; t==Tidbinbilla; g==Greenbank; u==Usuda [ ] Add reconstr-orbit binary spk file(s) (.bsp) to V050j.egb -- look for ??? Ensure these .bsp files are in the job directory and cover required tracking pass time ranges. [ ] Check NOTO.st for correct parameters...modify if necessary. NOTO.ev files contain events for ALL channels...modification required if pulsar gating is used. Comment .ev file reference if not required. Check pt_type and set Synthetic Autocorrelator parms for best result. [ ] Add constant station delay to station clock model file NOTO_c.smb. This must always be >= 0.0. [ ] Add CALIBRATION and ANTENNA coefficients to NOTO.cal -- if required. [ ] Check SESHAN25.st for correct parameters...modify if necessary. SESHAN25.ev files contain events for ALL channels...modification required if pulsar gating is used. Comment .ev file reference if not required. Check pt_type and set Synthetic Autocorrelator parms for best result. [ ] Add constant station delay to station clock model file SESHAN25_c.smb. This must always be >= 0.0. [ ] Add CALIBRATION and ANTENNA coefficients to SESHAN25.cal -- if required. [ ] Check VSOP_SC.st for correct parameters...modify if necessary. VSOP_SC.ev files contain events for ALL channels...modification required if pulsar gating is used. Check pt_type and set Synthetic Autocorrelator parms for best result. [ ] NOTE: If VSOP_SC logs do not contain flag data, these must be extracted from 'models.out' after make'ing the job and put in the VSOP_SC.ev file in the proper format. Look for 'linear connection'. [ ] Add TCF FITS file references (*.kcX) to VSOP_SC_l.smb -- look for ?? X - d==Goldstone; m==Madrid; t==Tidbinbilla; g==Greenbank; u==Usuda IF TCF FILES ARE NOT AVAILABLE then the downlink delay must be added. [ ] Add CALIBRATION and ANTENNA coefficients to VSOP_SC.cal -- if required. [ ] Check AT.st for correct parameters...modify if necessary. AT.ev files contain events for ALL channels...modification required if pulsar gating is used. Comment .ev file reference if not required. Check pt_type and set Synthetic Autocorrelator parms for best result. [ ] Add GPS clock offset model to station clock model file AT_c.smb. If station time is faster/leading GPS time then it is a (+)'ve delay. [ ] Add constant station delay to station clock model file AT_c.smb. This must always be >= 0.0. [ ] NOTE: 'AT' is a phased array...THE COORDINATES MUST BE SET in the finlocq.dat file from the PCFS log. Comment out other coordinates. [ ] Add CALIBRATION and ANTENNA coefficients to AT.cal -- if required. [ ] Check MOP.st for correct parameters...modify if necessary. MOP.ev files contain events for ALL channels...modification required if pulsar gating is used. Comment .ev file reference if not required. Check pt_type and set Synthetic Autocorrelator parms for best result. [ ] Add GPS clock offset model to station clock model file MOP_c.smb. If station time is faster/leading GPS time then it is a (+)'ve delay. [ ] Add constant station delay to station clock model file MOP_c.smb. This must always be >= 0.0. [ ] Add CALIBRATION and ANTENNA coefficients to MOP.cal -- if required. [ ] Check USUDA64.st for correct parameters...modify if necessary. USUDA64.ev files contain events for ALL channels...modification required if pulsar gating is used. Comment .ev file reference if not required. Check pt_type and set Synthetic Autocorrelator parms for best result. [ ] Add GPS clock offset model to station clock model file USUDA64_c.smb. If station time is faster/leading GPS time then it is a (+)'ve delay. [ ] Add CALIBRATION and ANTENNA coefficients to USUDA64.cal -- if required. [ ] Check V050j.bs for correct baselines...remove comments if baseline module autocorrelation is required. Check baseline integration times. [ ] Ensure that SOURCE '1147+245' is in ~/smdb/finblokq.dat or in finlocq.dat Ensure source coordinates are IDENTICAL to that in the V050j.sum file. [ ] Ensure that SOURCE '1156+295' is in ~/smdb/finblokq.dat or in finlocq.dat Ensure source coordinates are IDENTICAL to that in the V050j.sum file. [ ] Update file 1147+245.cal -- if necessary for cc2fits (source coordinates are automatically extracted from the V050j.eg file). [ ] Update file 1156+295.cal -- if necessary for cc2fits (source coordinates are automatically extracted from the V050j.eg file). [ ] Check to ensure that ~/smdb/finals.data is up-to-date for this obs. [ ] When all above checks are complete and all auxillary TCF and bsp files are installed, run 'makeV050j'. [ ] Check 'models.out' for any model generation ERRORs or WARNINGs [ ] 'makeV050j' ran ok? [ ] Run 'cc2fits' until BSD file catalogging starts -- to ensure job is FITS exportable. [ ] Create job V050j directory on geo (e.g. geod1/V050j), copy 'cc2fits.control' and edit it in preparation for FITS export and raw data archive. [ ] Job 'V050j' is ready for correlation. --------------------- JOB 'V050j' PLAYBACK SCHEDULE ------------------ NOT SES VSO AT MOP USU 352-14:00+00 - - - - - - +05 - - - - - - +10 - - - - - - +15 - - - - - - +20 - - - - - - +25 - - - - - - +30 - - - - - T** +35 - - - - - P +40 - - - - - P +45 - - - - - P +50 - - - - - P +55 - - - - - P 352-15:00+00 - - - - - P +05 - - - - - P +10 - - - - - P +15 - - - - - P +20 - - - - - P +25 - - - - - P +30 - - - - - P +35 - - - - - P +40 - - - - - P +45 - - - - - P +50 - - - - - P +55 - - - - - P 352-16:00+00 - - - - - P +05 - - - - - P +10 - - - - - P +15 - - - - - P +20 - - - - - P +25 - - - - - P +30 - - - - - P +35 - - - - - P +40 - - - - - P +45 - - - - - P +50 - - - - - P +55 - - - - - P 352-17:00+00 - - - - - P +05 - - - - - P +10 - - - - - P +15 - - - - - P +20 - - - - - P +25 - T** - T** T** P +30 - P - P P P +35 - P - P P P +40 - P - P P P +45 - P T** P P P +50 - P P P P P +55 - P P P P P 352-18:00+00 - P P P P P +05 - P P P P P +10 - P P P P P --------------------- JOB 'V050j' PLAYBACK SCHEDULE ------------------ NOT SES VSO AT MOP USU +15 - P P P P P +20 - P P P P P +25 - P P P P P +30 - P P P P P +35 - P P P P P +40 - P P P P P +45 - P P P P P +50 - P P P P P +55 - P P P P P 352-19:00+00 - P P P P P +05 - P P P P P +10 - P P P P P +15 - P P P P P +20 - P P P P P +25 - P P P P P +30 - P P P P P +35 - P P P P P +40 - P P P P P +45 - P P P P P +50 - P P P P P +55 - P P P P P 352-20:00+00 - P P P P P +05 - P P P P P +10 - P P P P P +15 - P P P P P +20 - P P P P P +25 - P P P P P +30 - P P P P P +35 - P P P P P +40 - P P P P P +45 - P P P P P +50 - P P P P P +55 - P P P P P 352-21:00+00 - P - P P P +05 - P - P P P +10 - P - P P P +15 - P - P P P +20 - P - P P P +25 - P - P P P +30 - P - P P - +35 - P - P P - +40 - P - P P - +45 - P - P P - +50 - P - P P - +55 - P - P P - 352-22:00+00 - P - P P - +05 T** P - P P - +10 P P - P P - +15 P P - P P - +20 P P - P P - +25 P P - P P - --------------------- JOB 'V050j' PLAYBACK SCHEDULE ------------------ NOT SES VSO AT MOP USU +30 P P - P P - +35 P P - P P - +40 P P - P P - +45 P P - P P - +50 P P - P P - +55 P P - P P - 352-23:00+00 - - - - - - +05 P T** - T** - - +10 P P - P - - +15 P P - P - - +20 P P - P - - +25 P P - P - - +30 P P - P - - +35 P P - P - - +40 P P - P - - +45 P P - P - - +50 P P - P - - +55 P P - - - - 353-00:00+00 P P - - - - +05 P P - - - - +10 P P T** - - - +15 P P P - - - +20 P P P - - - +25 P P P - - - +30 P P P - - - +35 P P P - - - +40 P P P - - - +45 P P P - - - +50 P P P - - - +55 P P P - - - 353-01:00+00 P P P - - - +05 P P P - - - +10 P P P - - - +15 P P P - - - +20 P P P - - - +25 P P P - - - +30 P P P - - - +35 P P P - - - +40 P P P - - - +45 P P P - - - +50 P P P - - - +55 P P P - - - 353-02:00+00 P P P - - - +05 P P P - - - +10 P P P - - - +15 P P P - - - +20 P P P - - - +25 P P P - - - +30 P P P - - - +35 P P P - - - +40 P P P - - - --------------------- JOB 'V050j' PLAYBACK SCHEDULE ------------------ NOT SES VSO AT MOP USU +45 P P P - - - +50 P P P - - - +55 P P P - - - 353-03:00+00 P P P - - - +05 P P P - - - +10 P P P - - - +15 P P P - - - +20 P P P - - - +25 P P - - - - +30 - - - - - - +35 - - - - - - +40 - - - - - - +45 - - - - - - ============ JOB 'V050j' TRACKING STATION PERFORMANCE SUMMARY ============= *****TO BE FILLED IN BY PR***** 'GBANK_TS' 1997-352-17:44:00 --> 1997-352-21:04:52 % fringes: _______ ~Res. del: _______ ~Res. drate: _______ 'TDBIN_TS' 1997-353-00:10:00 --> 1997-353-03:28:13 % fringes: _______ ~Res. del: _______ ~Res. drate: _______