cje2c3l Version 1.22d Thu Oct 7 15:07:37 PDT 1999 ============================== cje2c3l VS05r Build Summary ============================== Job Start Epoch: 2000-096-10:00:00 Job Stop Epoch: 2000-096-18:15:13 Duration of job: 8.3 hours Tape change epochs: 0 Stations: 'HARTRAO' (grt) 'HOBART' (grt) 'KASHIMA' (grt) 'KALYAZIN' (grt) 'MOP' (grt) 'SESHAN25' (grt) Sources: 'J1150-00' '1253-055' '' 'J1253-05' Tape ids: 'CA-3-0077817' 'ATNF0178' 'CA-3-001640C' 'CA-3-0014208' 'CA-3-0048310' 'AT-3-0000416' 'CA-3-0011003' Totals: [19] PB_STARTs [19] PB_STOPS [7] Tape ids [4] PCFS logs [0] SRT logs This job was built by ________________ on Tue May 9 10:46:07 2000 Number of baselines at build time: 15 ACTUAL: ____________ Total number of lags at build time: 15360 ACTUAL: ____________ Duration of job at build time: 8.3 HRS ACTUAL: _____________ Checked and ready for correlation. Date: _________________ Person: ________________ =========================== CHECKLIST for job 'VS05r' =========================== Complete this checklist before running 'makeVS05r'. [ ] Copy the experiment VS05r.sum file and any additional note files to the job's working directory. If ATNF telescopes are involved, note files in the form of .notes must be downloaded from the ATNF server 'ftp.atnf.csiro.au' in the directory '/pub/people/vlbi/vsop/logs/'. These note files contain information ***CRITICAL*** to the correlation of ATNF telescopes. [ ] Check VS05r.jb for correct parameters (sample rate etc.) Check default integration time. [ ] Check HARTRAO.st for correct parameters...modify if necessary. HARTRAO.ev files contain events for ALL channels...modification required if pulsar gating is used. Comment .ev file reference if not required. Check pt_type and set Synthetic Autocorrelator parms for best result. [ ] Add constant station delay to station clock model file HARTRAO_c.smb. This must always be >= 0.0. [ ] Add CALIBRATION and ANTENNA coefficients to HARTRAO.cal -- if required. [ ] Check HOBART.st for correct parameters...modify if necessary. HOBART.ev files contain events for ALL channels...modification required if pulsar gating is used. Comment .ev file reference if not required. Check pt_type and set Synthetic Autocorrelator parms for best result. [ ] Add constant station delay to station clock model file HOBART_c.smb. This must always be >= 0.0. [ ] Add CALIBRATION and ANTENNA coefficients to HOBART.cal -- if required. [ ] Check KASHIMA.st for correct parameters...modify if necessary. KASHIMA.ev files contain events for ALL channels...modification required if pulsar gating is used. Comment .ev file reference if not required. Check pt_type and set Synthetic Autocorrelator parms for best result. [ ] Add GPS clock offset model to station clock model file KASHIMA_c.smb. If station time is faster/leading GPS time then it is a (+)'ve delay. [ ] Add constant station delay to station clock model file KASHIMA_c.smb. This must always be >= 0.0. [ ] Add CALIBRATION and ANTENNA coefficients to KASHIMA.cal -- if required. [ ] Check KALYAZIN.st for correct parameters...modify if necessary. KALYAZIN.ev files contain events for ALL channels...modification required if pulsar gating is used. Comment .ev file reference if not required. Check pt_type and set Synthetic Autocorrelator parms for best result. [ ] Add GPS clock offset model to station clock model file KALYAZIN_c.smb. If station time is faster/leading GPS time then it is a (+)'ve delay. [ ] Add constant station delay to station clock model file KALYAZIN_c.smb. This must always be >= 0.0. [ ] Add CALIBRATION and ANTENNA coefficients to KALYAZIN.cal -- if required. [ ] Check MOP.st for correct parameters...modify if necessary. MOP.ev files contain events for ALL channels...modification required if pulsar gating is used. Comment .ev file reference if not required. Check pt_type and set Synthetic Autocorrelator parms for best result. [ ] Add GPS clock offset model to station clock model file MOP_c.smb. If station time is faster/leading GPS time then it is a (+)'ve delay. [ ] Add constant station delay to station clock model file MOP_c.smb. This must always be >= 0.0. [ ] Add CALIBRATION and ANTENNA coefficients to MOP.cal -- if required. [ ] Check SESHAN25.st for correct parameters...modify if necessary. SESHAN25.ev files contain events for ALL channels...modification required if pulsar gating is used. Comment .ev file reference if not required. Check pt_type and set Synthetic Autocorrelator parms for best result. [ ] Add GPS clock offset model to station clock model file SESHAN25_c.smb. If station time is faster/leading GPS time then it is a (+)'ve delay. [ ] Add constant station delay to station clock model file SESHAN25_c.smb. This must always be >= 0.0. [ ] Add CALIBRATION and ANTENNA coefficients to SESHAN25.cal -- if required. [ ] Check VS05r.bs for correct baselines...remove comments if baseline module autocorrelation is required. Check baseline integration times. [ ] Ensure that SOURCE 'J1150-00' is in ~/smdb/finblokq.dat or in finlocq.dat Ensure source coordinates are IDENTICAL to that in the VS05r.sum file. [ ] Ensure that SOURCE '1253-055' is in ~/smdb/finblokq.dat or in finlocq.dat Ensure source coordinates are IDENTICAL to that in the VS05r.sum file. [ ] Ensure that SOURCE '' is in ~/smdb/finblokq.dat or in finlocq.dat Ensure source coordinates are IDENTICAL to that in the VS05r.sum file. [ ] Ensure that SOURCE 'J1253-05' is in ~/smdb/finblokq.dat or in finlocq.dat Ensure source coordinates are IDENTICAL to that in the VS05r.sum file. [ ] Update file J1150-00.cal -- if necessary for cc2fits (source coordinates are automatically extracted from the VS05r.eg file). [ ] Update file 1253-055.cal -- if necessary for cc2fits (source coordinates are automatically extracted from the VS05r.eg file). [ ] Update file .cal -- if necessary for cc2fits (source coordinates are automatically extracted from the VS05r.eg file). [ ] Update file J1253-05.cal -- if necessary for cc2fits (source coordinates are automatically extracted from the VS05r.eg file). [ ] Check to ensure that ~/smdb/finals.data is up-to-date for this obs. [ ] When all above checks are complete run 'makeVS05r'. [ ] Check 'models.out' for any model generation ERRORs or WARNINGs [ ] 'makeVS05r' ran ok? [ ] Run 'cc2fits' until BSD file catalogging starts -- to ensure job is FITS exportable. [ ] Create job VS05r directory on geo (e.g. geod1/VS05r), copy 'cc2fits.control' and edit it in preparation for FITS export and raw data archive. [ ] Job 'VS05r' is ready for correlation. ================== EXPERIMENT 'VS05r' SUMMARY REPORT ================== **** TO BE FILLED IN BY THE PR AND GIVEN TO THE OPERATIONS MANAGER **** DATE: _________________ PR: ____________ ================================ STATION FRINGE DETECTION SUMMARY ================================ HARTRAO: [ ] fringes detected Comments: Delay corr: _________ us Delay resid: _________ us Rate resid: _________ ps/s HOBART: [ ] fringes detected Comments: Delay corr: _________ us Delay resid: _________ us Rate resid: _________ ps/s KASHIMA: [ ] fringes detected Comments: Delay corr: _________ us Delay resid: _________ us Rate resid: _________ ps/s KALYAZIN: [ ] fringes detected Comments: Delay corr: _________ us Delay resid: _________ us Rate resid: _________ ps/s MOP: [ ] fringes detected Comments: Delay corr: _________ us Delay resid: _________ us Rate resid: _________ ps/s SESHAN25: [ ] fringes detected Comments: Delay corr: _________ us Delay resid: _________ us Rate resid: _________ ps/s ==================== DATA RELEASE SUMMARY ==================== [ ] RELEASED [ ] ABANDONED Reason: Release date: _____________________________ Data volume: ________ FITS files; _______ Gbytes Data Shipments: [ ] PI: ____________________ DAT / Exabyte [ ] U of C: Exabyte [ ] Other: _________________ DAT / Exabyte Comments: