cje2c3l Version 1.22d Thu Oct  7 15:07:37 PDT 1999

==============================
cje2c3l VS06z Build Summary
==============================

	Job Start Epoch: 1999-229-15:00:00
	Job Stop Epoch:  1999-229-20:15:06
	Duration of job: 5.3 hours
	Tape change epochs: 0
	Stations:
		'MOP' (grt)
		'VSOP_SC' (srt)
	Tracking Stations:
		'GBANK_TS'
	Tracking PASSES:
		'GBANK_TS' 1999-229-16:41:43 --> 1999-229-19:30:43
	Sources:
		'J0149+05'
		'0202+149'
	Tape ids:
		'ATNF0311'
		'CA-3-0049917'

	Totals: [3] PB_STARTs  [3] PB_STOPS  [2] Tape ids
		[1] PCFS logs   [1] SRT logs


This job was built by ________________ on Wed Oct 27 14:48:34 1999


Number of baselines at build time: 1 ACTUAL: ____________

Total number of lags at build time: 1024 ACTUAL: ____________

Duration of job at build time:  5.3 HRS ACTUAL: _____________


Checked and ready for correlation.

Date: _________________  Person: ________________

===========================
CHECKLIST for job 'VS06z'
===========================

Complete this checklist before running 'makeVS06z'.

[ ] Copy the experiment VS06z.sum file and any additional note files to
    the job's working directory.  If ATNF telescopes are involved, note files
    in the form of <job_name><st>.notes must be downloaded from the ATNF
    server 'ftp.atnf.csiro.au' in the directory
    '/pub/people/vlbi/vsop/logs/<mon><yr>'.  These note files contain
    information ***CRITICAL*** to the correlation of ATNF telescopes.

[ ] Check VS06z.jb for correct parameters (sample rate etc.)
    Check default integration time.

[ ] Ensure that TCF file(s) (*.kcX) for tracking station 'GBANK_TS' are in the
    job directory for time ranges (yymmddhhmm): 9908171641 to 9908171930.
    X - d==Goldstone; m==Madrid; t==Tidbinbilla; g==Greenbank; u==Usuda

[ ] Add reconstr-orbit binary spk file(s) (.bsp) to VS06z.egb -- look for ???
    Ensure these .bsp files are in the job directory and cover required
    tracking pass time ranges.

[ ] Check MOP.st for correct parameters...modify if necessary.
    MOP.ev files contain events for ALL channels...modification required
    if pulsar gating is used.  Comment .ev file reference if not required.
    Check pt_type and set Synthetic Autocorrelator parms for best result.

[ ] Add GPS clock offset model to station clock model file MOP_c.smb.
    If station time is faster/leading GPS time then it is a (+)'ve delay.

[ ] Add constant station delay to station clock model file MOP_c.smb.
    This must always be >= 0.0.

[ ] Add CALIBRATION and ANTENNA coefficients to MOP.cal -- if required.

[ ] Check VSOP_SC.st for correct parameters...modify if necessary.
    VSOP_SC.ev files contain events for ALL channels...modification required
    if pulsar gating is used.
    Check pt_type and set Synthetic Autocorrelator parms for best result.

[ ] NOTE: If VSOP_SC logs do not contain flag data, these must be extracted
    from 'models.out' after make'ing the job and put in the VSOP_SC.ev
    file in the proper format.  Look for 'linear connection'.

[ ] Add TCF FITS file references (*.kcX) to VSOP_SC_l.smb -- look for ??
    X - d==Goldstone; m==Madrid; t==Tidbinbilla; g==Greenbank; u==Usuda
    IF TCF FILES ARE NOT AVAILABLE then the downlink delay must be added.

[ ] Add CALIBRATION and ANTENNA coefficients to VSOP_SC.cal -- if required.

[ ] Check VS06z.bs for correct baselines...remove comments if baseline module
    autocorrelation is required.  Check baseline integration times.

[ ] Ensure that SOURCE 'J0149+05' is in ~/smdb/finblokq.dat or in finlocq.dat
    Ensure source coordinates are IDENTICAL to that in the VS06z.sum file.

[ ] Ensure that SOURCE '0202+149' is in ~/smdb/finblokq.dat or in finlocq.dat
    Ensure source coordinates are IDENTICAL to that in the VS06z.sum file.

[ ] Update file J0149+05.cal -- if necessary for cc2fits (source coordinates
    are automatically extracted from the VS06z.eg file).

[ ] Update file 0202+149.cal -- if necessary for cc2fits (source coordinates
    are automatically extracted from the VS06z.eg file).

[ ] Check to ensure that ~/smdb/finals.data is up-to-date for this obs.

[ ] When all above checks are complete and all auxillary TCF and bsp files
    are installed, run 'makeVS06z'.

[ ] Check 'models.out' for any model generation ERRORs or WARNINGs

[ ] 'makeVS06z' ran ok?

[ ] Run 'cc2fits' until BSD file catalogging starts -- to ensure job is FITS
    exportable.

[ ] Create job VS06z directory on geo (e.g. geod1/VS06z), copy 'cc2fits.control'
    and edit it in preparation for FITS export and raw data archive.

[ ] Job 'VS06z' is ready for correlation.



	================== EXPERIMENT 'VS06z' SUMMARY REPORT ==================

	**** TO BE FILLED IN BY THE PR AND GIVEN TO THE OPERATIONS MANAGER ****

	DATE: _________________ PR: ____________

	================================
	STATION FRINGE DETECTION SUMMARY
	================================

	MOP:
	    [  ] fringes detected                        Comments:
	    Delay corr:  _________ us
	    Delay resid: _________ us    Rate resid: _________ ps/s

	VSOP_SC:
	    [  ] fringes detected                        Comments:
	    Delay corr:  _________ us
	    Delay resid: _________ us    Rate resid: _________ ps/s

	====================================
	TRACKING STATION PERFORMANCE SUMMARY
	====================================

	'GBANK_TS' 1999-229-16:41:43 --> 1999-229-19:30:43
	   % fringes: _______ ~Res. del: _______ ~Res. drate: _______

	====================
	DATA RELEASE SUMMARY
	====================

	[ ] RELEASED
	[ ] ABANDONED Reason:

	Release date: _____________________________

	Data volume: ________ FITS files; _______ Gbytes

	Data Shipments: 
	           [  ] PI: ____________________  DAT / Exabyte
	           [  ] U of C:                   Exabyte

	           [  ] Other: _________________  DAT / Exabyte

	Comments: