==============================
cje2c3l VT109 Build Summary
==============================

	Job Start Epoch: 1997-102-08:00:00
	Job Stop Epoch:  1997-102-15:45:30
	Duration of job: 7.8 hours
	Tape change epochs: 0
	Stations:
		'NAR' (grt)
		'HOBART' (grt)
		'TID' (grt)
	Sources:
		'1334-127'
		'3c273'
		'sgrn2s'
		'1934-638'
	Tape ids:
		'AT-3-0000315'
		'UT-3-000262E'
		'AT-1-002931E'

	Totals: [15] PB_STARTs  [15] PB_STOPS  [3] Tape ids
		[3] PCFS logs   [0] SRT logs


This job was built by ________________ on Tue Apr 15 10:54:54 1997


Number of baselines at build time: 3 ACTUAL: ____________

Total number of lags at build time: 6144 ACTUAL: ____________


Checked and ready for correlation.

Date: _________________  Person: ________________

===========================
CHECKLIST for job 'VT109'
===========================

Complete this checklist before running 'makeVT109'.

[ ] Check VT109.jb for correct parameters (sample rate etc.)
    Check default integration time.

[ ] Check to ensure that station 'NAR' is in ~/smdb/finblokq.dat or
    in finlocq.dat.

[ ] Check NAR.st for correct parameters...modify if necessary.
    NAR.ev files contain events for ALL channels...modification required
    if pulsar gating is used.  Comment .ev file reference if not required.

[ ] Add clock offsets/model to station clock model file NAR_c.smb.

[ ] Add CALIBRATION and ANTENNA coefficients to NAR.cal -- if required.

[ ] Check to ensure that station 'HOBART' is in ~/smdb/finblokq.dat or
    in finlocq.dat.

[ ] Check HOBART.st for correct parameters...modify if necessary.
    HOBART.ev files contain events for ALL channels...modification required
    if pulsar gating is used.  Comment .ev file reference if not required.

[ ] Add clock offsets/model to station clock model file HOBART_c.smb.

[ ] Add CALIBRATION and ANTENNA coefficients to HOBART.cal -- if required.

[ ] Check to ensure that station 'TID' is in ~/smdb/finblokq.dat or
    in finlocq.dat.

[ ] Check TID.st for correct parameters...modify if necessary.
    TID.ev files contain events for ALL channels...modification required
    if pulsar gating is used.  Comment .ev file reference if not required.

[ ] Add clock offsets/model to station clock model file TID_c.smb.

[ ] Add CALIBRATION and ANTENNA coefficients to TID.cal -- if required.

[ ] Check VT109.bs for correct baselines...remove comments if baseline module
    autocorrelation is required.  Check baseline integration times.

[ ] Ensure that SOURCE '1334-127' is in ~/smdb/finblokq.dat or in finlocq.dat

[ ] Ensure that SOURCE '3c273' is in ~/smdb/finblokq.dat or in finlocq.dat

[ ] Ensure that SOURCE 'sgrn2s' is in ~/smdb/finblokq.dat or in finlocq.dat

[ ] Ensure that SOURCE '1934-638' is in ~/smdb/finblokq.dat or in finlocq.dat

[ ] Update file 1334-127.cal -- add source coordinates etc. for cc2fits.

[ ] Update file 3c273.cal -- add source coordinates etc. for cc2fits.

[ ] Update file sgrn2s.cal -- add source coordinates etc. for cc2fits.

[ ] Update file 1934-638.cal -- add source coordinates etc. for cc2fits.

[ ] Check to ensure that ~/smdb/finals.data is up-to-date for this obs.

[ ] Edit 'cc2fits.control' for correct output parameters.

[ ] When all above checks are complete run 'makeVT109'.

[ ] Check 'models.out' for any model generation ERRORs or WARNINGs

[ ] 'makeVT109' ran ok...job 'VT109' ready for correlation.